• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.1447-1449
• /
• 2009

We report the syntheses bis-(N,N-diethylaminoethyl) perylene-3,4,9,10-tetracarboxylic diimide (PDI) of lyotropic chromonic liquid crystal and it dissolves in photocurable ionic monomer solution. PDI-acrylic acid solution was observed whether liquid crystal phase appeared in each concentration. Thin film polarizer was prepared by simultaneously coating and aligning the solution of PDI-acrylic acid (in the chromonic nematic phase) onto glass substrates using a mechanical shearing force and was cured by irradiation of UV light. Also Photopatterned polarizer is manufactured by same process.

• 반도체디스플레이기술학회지
• /
• 제16권4호
• /
• pp.1-4
• /
• 2017

Encapsulation of organic based devices is essential issue due to easy deterioration of organic material by water vapor. Atomic layer deposition (ALD) is a promising solution because of its low temperature deposition and quality of the deposited film. Moisture permeation has a mechanism to pass through defects, Thin Film Encapsulation using inorganic / organic / inorganic hybrid film has been used as promising technology. $Al_2O_3$ / Polymer / $Al_2O_3$ multilayer film has shown excellent environmental protection characteristics despite of thin thicknesses of the films.

• 반도체디스플레이기술학회지
• /
• 제17권2호
• /
• pp.1-5
• /
• 2018

Elastic resistive pressure sensor is fabricated by a direct spray coating of silver nanowires (AgNWs) on uncured polydimethylsiloxane (PDMS) and an additional coating of a conductive polymer, poly(3,4-ethylenedioxythiophene): poly (styrene sulfonate) (PEDOT:PSS). To improve the sensitive and stability, we have fabricated sandwich-structured AgNW/polymer sensor where two AgNW/polymer-coated PDMS films are laminated with the conducting surfaces contacted by pressure lamination. It shows a resistance decrease upon loading due to the formation of dense network of AgNWs. It is demonstrated that the sandwich-structured AgNW/polymer sensor exhibits very high sensitivity ($2.59kPa^{-1}$) and gauge factor (37.8) in the low pressure regime. It can also detect a subtle placement and removal of a weight as low as 3.4 mg, the corresponding pressure of which is about 5.4 Pa. It is shown that the protrusion of AgNWs from PDMS is suppressed substantially by the over-coated PEDOT:PSS layer, thereby reducing hysteresis and rendering the sensor more stable.

• Journal of Pharmaceutical Investigation
• /
• 제20권3호spc1호
• /
• pp.51-76
• /
• 1990

It is sometimes said lately that the pH of the human gastric juice is significantly different among individuals. Thus, the dissolution behavior of coated solid dosage forms should preferably be independent of the pH of the test solution. With these points as a background, the effect of pH on the dissolution velocity of coated tablets was studied to compare that of Pharmacoat with other gastric soluble film coating materials. Three viscosity types of Pharmacoat have been available(3, 6 and 15cP) until now. the 6cP type has been considered to be the most suitable for a tablet coating amongst the three types. The 3 cP type with a low degree of polymerization, is capable of providing high concentration, but the film strength is so inferior that sometimes cracking of the film may occur. On the other hand, in the case of the 15cP type, high polymer concentration cannot be achieved because of the high dgree of polymerization, and thus it is uneconomical for coating. Now, there is a strong demand to reduce the coating time even when HPMC is used in the 6cP type in order to reduce the coating cost. In order to improve this problem, we have concentrated our attention on reducing the viscosity value of HPMC to an allowable lower limit from 6cP. As a result of this study, it was found that the reduction of the viscosity value to around 4.5cP enabled the use of a higher solution concentration and an incidental shorter coating time without giving any substantial adverse effects on the properties of coated preparations. These experiment results are presented in the later part of this presentation. Based on this study, we have added the viscosity type of 4.5cP as one of the Pharmacoat products as Pharmacoat-645.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.373-374
• /
• 2007

We have fabricated polymer light-emitting diodes(PLED) in a structure of Glass/ITO/PVK/Al. Poly(N-vinylcabazole) (PVK) was deposited on the ITO glass with the spin coating method. PVK thickness is respectively 500nm, 300nm, 250nm and 200nm with the spin coter rotation speed of 2000, 3000, 4000 and 5000rpm. V-I, wavelength-transmittance, P-L and SEM of the fabricated devices were measured. From the result of P-L measurement, it was kept the optic properties of PVK raw powder when PVK thickness is 250nm. The knee-voltage of PVK PLED with 250nm thickness was 7V.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권5호
• /
• pp.267-271
• /
• 2006

A polymeric waveguide-type wavelength filter based on a Bragg grating has been proposed and fabricated using the simple nanoimpring technique, for the first time to our knowledge. An ultraviolet transparent stamp with the single-mode waveguide pattern incorporating a surface-relief-type Bragg grating was specially designed selective dry-etching process. Using this stamp, the device fabrication was substantially involving just a single-step process of imprint followed by polymer spin-coating. The achieved maximum reflection was higher than 25 dB at the center wavelength of 1569 nm. And the 3-dB bandwidth was 0.8 nm for the device length of 1.5 cm.

• Macromolecular Research
• /
• 제11권3호
• /
• pp.157-162
• /
• 2003

6FDA-based polyimides were prepared from the thermal imidization reaction of 6FDA with diamines of BAPAF, DAP, and DABA having a polar group of hydroxyL or carboxyl. Properties of the dense polyimide membranes were characterized and their gas permeation properties for H$_2$, $CO_2$, $O_2$, $N_2$, and CH$_4$ were investigated. Permeabilities, diffusion coefficients and diffusivity selectivities of polar group-containing polyimide membranes including 6FDA-BAPAF, 6FDA-DAP, and 6FDA-DABA polymer for the gases did not change largely. The separation properties of 6FDA-TrMPD polyimide membrane used as a reference polymer were compared with those of the polyimide membranes mentioned above. It was found that the polyimides of 6FDA-BAPAF, 6FDA-DAP, and 6FDA-DABA, which were soluble in alcohol or/and 2-methoxyethanol, could be applicable to the preparation of a dense composite membrane by dip-coating method.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.7.1-7.1
• /
• 2011

Nanoporous templates have been widely used for the development of new functional nanostructured materials suitable for electronics, optics, magnetism, and energy storage materials. We have prepared nanoporous templates by using thin films of mixtures of polystyrene-block-poly (methyl methacrylate) (PS-b-PMMA) and PMMA homopolymers. These templates have cylindrical nanoholes spanning the entire thickness of the film. Some applications of nanoporous templates are introduced: a) anti-reflective coating, b) the preparation of conducting polymer nanowires of poly (pyrrole), poly (3,4-ethylenedioxy-thiopene) onto a glass coated with indium-tin-oxide, and c) the separation membranes for biomaterials. We found that when the pore fraction of nanoholes in the film was ~0.68, almost zero reflectance at a specific wavelength, which can be changed with film thickness, was achieved at visible wavelengths Furthermore, ultra high density array of conducting nanowires was successfully prepared onto various substrates including flexible polymer. Due to highly alignment of polymer chain along the nanowire direction, the conductivity was much increased. Furthermore, these nanoporous films were found to be very effective for the separation of human Rhinovirus type 14 (HRV 14), major pathogen of a common cold in humans, from the buffer solution. We also found that when the pore size was effectively controlled down to 6 nm, a single file diffusion was observed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.834-836
• /
• 2008

We demonstrated micro-scale conducting polymer patterning based on a selective surface treatment. A substrate with a patterned photoresist was immersed into OTS (Octadecyltrichlosilnae) solution. The protected substrate areas were hydrophilic after removing the PR resist, where a conducting polymer solution was coated selectively by spin-coating method.

• 펄프종이기술
• /
• 제43권2호
• /
• pp.49-56
• /
• 2011

Mulching technique is used to control the temperature and moisture content of soil by covering the ground surface. Most kinds of mulching film are made of polyethylene which is non-biodegradable synthetic polymer. Utilizing these films has been one of the main sources in soil pollution. Thus residual films under the ground should be removed after a certain period of time. Therefore, an alternative mulching material made of biodegradable functional paper is considered instead of non-biodegradable films. The mulching sheet produced from paper basis has a functionality to be naturally degraded and then recycled to the bio-materials on soil. In this study, the paper based-mulching sheet coated with biodegradable polymer was specially produced using a laboratory bar coater. Coating colors prepared by dissolving PBS/PLA in chloroform were applied to kraft paper. The mechanical strength and aging properties of this mulching sheet were investigated. The burst strength of polymer-coated paper was decreased with the increase of the PBS ratio in PBS/PLA blends, and, in particular, 30/70 blending condition led to good stability in heat-aging atmosphere for 60 days.