• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.216-219
• /
• 2002

Conventional piezoelectric lead-zirconate-titanate (PZT) senor has high sensitivity, but it is very brittle. Recently polymer films such as polyvinylidene fluoride (PVDF) have been used use as a sensor. The advantages of PVDF are the flexibility and mechanical toughness. Simple process and possible several shapes are also additional advantages. PVDF sensor can be directly embedded and attached to a structure. In this study, PVDF sensor was embedded in single glass fiber/epoxy composites whereas PZT sensor with AE was attached to single fiber composites (SFC). Piezoelectric sensor responds to interfacial damage of SFC. The signals measured by PVDF sensor were compared to PZT sensor. PZT sensor detected the signals of fiber fracture, matrix crack, interfacial debonding and even sensor delamination, whereas PVDF sensor only detected fiber fracture signals so far, because PZT sensor is much more sensitive than current PVDF sensor. Wave voltage of fiber fracture measured by PVDF sensor was lower than that of PZT sensor, but the results of fast Fourier transform (FFT) analysis were same. Wave velocity using two PZT sensors was also studied to know the internal and surface damage effect of epoxy specimens.

• 폴리머
• /
• 제24권4호
• /
• pp.564-570
• /
• 2000

욕조 생산시 발생하는 폐 FRP와 냉장고 등 가전품과 폐단열재로부터 발생하는 폐우레탄폼을 흡음 및 경량판재로 재활용하기 위하여 불포화 폴리에스테르 매트릭스 수지에 보강하여 복합재를 제조하였다. 또한 충진제의 함량의 변화가 복합재의 기계적 물성에 미치는 영향과 기지와 보강재간의 계면현상을 관찰하였다. 충진제의 함량이 70 wt%인 복합재의 인장강도는 82.34 MPa로 가장 우수하였으며, 인장탄성율은 보강재의 함량이 증가함에 따라 감소하였다. 또한 굴곡강도와 굴곡탄성율은 폐FRP의 함량이 70 wt%충진된 복합재가 가장 우수하였으며, 그 값은 각각 72.5, 958.4 MPa이었다. SEM 관찰 결과 70 wt% 충진된 충진제 매트릭스 수지의 계면에서 pull out 현상이 확인되지 않았으며 균열도 발생하지 않았고, 매트릭스 수지내에 충진된 폐 FRP/우레탄폼 충진제가 잘 분산되어 있음을 확인할 수 있었다.

• 한국인쇄학회지
• /
• 제16권1호
• /
• pp.1-11
• /
• 1998

Recently the study of the application of liquid crystal in industrial fields has developed rapidly. It is well known that the encapsulated liquid crystal is advantageous than raw liquid crystal for protection of surface pollution. This paper describes a new class of thermal sensor. It is that the liquid crystal polymer composite(LCPC) films consisting of a continuous LC phase embedded in a three-dimensional network of polymer matrix are formed by photopolymerization-induced phase separation. In this works, it has been demonstrated that consiste of a 8:2 mixture of chiral nematic liquid crystal and HX-620 has the greatest domain and it was best discoloration.

• 한국인쇄학회지
• /
• 제13권1호
• /
• pp.93-104
• /
• 1995

Liquid crystal-polymer composite(LCPC) films promising new materials for both projection displays and vision product. LCPC films consist of a continous liquid crystal phase embedded in a three- dimensional network of polymer matrix. The liquid crystal in these LC phases can be elecrtrically switched giving rise to an opaque scattering off-stats and a transparent, non-scatting on- stats. In this work. a premixture is composed of LC, UV-curable monomer and photonitiator. LCPC films are formed by photopolymerization induced phase separation from this premixture. In conclusion, structure and electro-optical properties of LCPC films strongly depends on the selection of monomer, LC content and curing rate.

• 폴리머
• /
• 제38권4호
• /
• pp.464-470
• /
• 2014

A chemo-mechanical method was used to prepare lignin-containing cellulose nanofibrils(L-CNF) from unbleached woodpulps dispersed uniformly in an organic solvent. L-CNF/PLA composites were obtained by solvent casting method. The effects of L-CNF concentration on the composite performances were characterized by tensile test machine, contact angle machine, scanning electron microscope (SEM), and Fourier transform infrared spectroscopy (FTIR). The tensile test results indicated that the tensile strength and elongation-at-break increased by 50.6% and 31.8% compared with pure PLA. The contact angle of PLA composites decreased from $79.3^{\circ}$ to $68.9^{\circ}$. The FTIR analysis successfully showed that L-CNF had formed intermolecular hydrogen bonding with PLA matrix.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.317-320
• /
• 1999

In this study, the piezoelectric ceramics PZT powder was synthesized by Wet-Dry combination method. And the flexible 1-3-0 type composites were fabricated with piezoceramic PZT and Eccogel polymer matrix embedded 3rd phase. Dielectric constant of 1-3-0 type composites was lower than that of single phase PZT ceramics. Thickness mode coupling factor k/sub t/ which was comparable with single phase PZT ceramics and mechanical quality factor Qm were about 0.65 and 6, respectively. These composites are considered as a good candidates for broad-band type transducer applications. The acoustic impedance of 1-3-0 type composites was lower than that of single phase PZT ceramics. Therefore, these composites would be better used for hydrophone applications.

• Elastomers and Composites
• /
• 제50권3호
• /
• pp.205-209
• /
• 2015

Magnesium oxide (MgO) reinforced polyamide-66 (PA66) composites were prepared through melt-compounding method in order to determine the possibility of using MgO particle as conductive filler in the polymer-based composite. The effects of MgO filler content on the thermal conductivity and mechanical properties for the PA66/MgO composites were investigated. The results showed that the addition of MgO filler to the PA66 matrix led to a large increase in thermal conductivity of the PA66/MgO composites. Tensile strengths of the PA66/MgO composites were slightly decreased as MgO filler loading increased. However, flexural strength and flexural modulus were improved with increasing filler loading. Notched Izod impact strengths were dramatically lowered by the addition of MgO filler.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.303-306
• /
• 1999

In this study, the piezoelectric ceramics PZT powder was synthesized by Wet-Dry combination method. The flexible 1-3-0 type composites were fabricated with piezoceramic PZT and Eccogel polymer matrix embedded 3rd phase. This paper represents the acoustic properties with various 3rd phase wt.%. The acoustic impedance of 1-3-0 type composites was lower than that of single phase PZT ceramics. The pulse-echo response of transducer fabricated with 1-3-0 type composites was better than solid PZT transducer.

• Structural Engineering and Mechanics
• /
• 제76권5호
• /
• pp.613-618
• /
• 2020

Exhausting oil resources and increasing pollution around the world are forcing researchers to look for new, renewable, biodegradable materials to lead sustainable development. The use of fiber reinforced composites based on natural fibres has increasingly begun as prospective materials for various engineering applications in the automotive, rail, construction and aerospace industries. The natural fiber chosen to make the composite material is plant-based fibre, e.g. jute fibre, and hemp fibre. Thermosetting polymer based Epoxy (LY556) was utilized as matrix material and The composites were produced using hand lay-up technique. The fabricated composites were tested for acoustic testing, thermo-gravimetric analysis (TGA) and flammability testing to asses sound absorption, thermal decomposition and fire resistivity of the structures. Hemp fibre composites have shown improved thermal stability over Jute fibre composites. However, the fire resistance characteristics of jute fibre composites are better as compared to hemp fibre composites. The sound absorption coefficient of composites was found to enhance with the increase of frequency.

• 한국수소및신에너지학회논문집
• /
• 제20권2호
• /
• pp.95-103
• /
• 2009

In order to improve the electrochemical, mechanical and electrocatalytic characteristics, engineering plastic of polyether ether ketone (PEEK) as polymer matrix was sulfonated (SPEEK) and the organic-inorganic blend composite membranes has been prepared by loading heteropoly acids (HPAs), including tungstophosphoric acid (TPA), molybdophosphoric acid (MoPA), and tungstosilicic acid (TSiA). And then these were covalently cross-linked (CL-SPEEK/HPA) as the electrolyte and MEA of polymer electrolyte membrane electrolysis (PEME). As a result, the optimum reaction conditions of CL-SPEEK/HPA was established and the electrochemical characteristics such as ion conductivity ($\sigma$) were in the order of magnitude: CL-SPEEK /TPA30 (${\sigma}=0.128\;S/cm^{-1}$) < /MoPA40 (${\sigma}=0.14\;S/cm^{-1})$ < /TSiA30 (${\sigma}=0.22\;S/cm^{-1}$) at $80^{\circ}C$, and mechanical characteristics such as tensile strength: CL-SPEEK /TSiA30 $\fallingdotseq$ /MoPA40 < /TPA30. Consequently, in regards of above characterisitics and oxidation durability, the CL-SPEEK/TPA30 exhibited a better performance in PEME than the others, but CL-SPEEK/MoPA40 showed the best electrocatalytic activity of cell voltage 1.71 V among the composite membranes. The dual effect of higher proton conductivity and electrocatalytic activity with the addition of HPAs, causes a synergy effect.