• Applied Chemistry for Engineering
• /
• v.8 no.1
• /
• pp.29-38
• /
• 1997

In the w/o concentrated emulsion, the volume fraction of the dispersed is greater than 0.74 and the hydrophilic liquid is dispersed in the hydrophobic liquid of the continuous phase. The emulsion has the same appearance and behaviour as a gel. The polarity of the hydrophilic liquids and hydrophobic liquids, the pH and the ionic strength of the hydrophilic liquid are found to be important factors in the stability at the polymerization temperature such as $50^{\circ}C$. The lower the polarity of the hydrophobic liquid and the higher the polarity of the hydrophilic liquid, the more stable the emulsion. Electron microscopy studies of the hydrophilic-hydrophobic polymer composites show that the particles of polyacrylamide, the dispersed phase, are separated by he network of the thin film of polystyrene, the continuous phase. This hydrophilic-hydrophobic polymer composites show higher permselectivity to water in the mixture of water-ethanol. The pervaporation experiment shows that the selectivity of the membrane ranges between 4-40 and increases with increasing enthanol concentration in the feed. The rate of permeation decreases with increasing ethanol concentration in the feed.

• Elastomers and Composites
• /
• v.50 no.2
• /
• pp.110-118
• /
• 2015

In this study, diethylaminoethyl methacrylate-styrene-butadiene terpolymer (DEAEMA-SBR), in which diethylaminoethyl methacrylate (DEAEMA) was introduced to the SBR molecule as a third monomer, was synthesized by cold emulsion polymerization. It is expected that amine group introduced to a rubber molecule would improve dispersion of silica by the formation of hydrogen bond (or ionic coupling) between the amine group and silanol groups of silica surface. The chemical structure of DEAEMA-SBR was analyzed using proton nuclear magnetic resonance spectroscopy (H-NMR), Fourier transform infrared spectroscopy (FTIR), gel permeation chromatography (GPC) and differential scanning calorimetry (DSC). Then, various properties of DEAEMA-SBR/silica composite such as crosslink density, bound rubber content, abrasion resistance, and mechanical properties were evaluated. As a result, bound rubber content and crosslink density of DEAEMA-SBR/silica compound were higher than those of the SBR 1721 composite. Abrasion resistance and moduli at 300% elongation of the DEAEMA-SBR/silica composite were better than those of SBR 1721 composite due to the high bound rubber content and crosslink density. These results are attributed to high affinity between DEAEMA-SBR and silica. The proposed study suggests that DEAEMA-SBR can help to improve mechanical properties and abrasion resistance of the tire tread part.

• Clean Technology
• /
• v.14 no.4
• /
• pp.256-264
• /
• 2008

In this study, using PBAST (poly(butylene adipate-co-succinate-co-terephthalate)) which was eco-friendly biodegradable aliphatic polyester, PBAST/PVA (poly(vinyl alcohol)) double-layered hollow microspheres were prepared with the water/oil/water multiple emulsion ($W_1/O/W_2$) method. The double-layered hollow microspheres were manufactured with the yield of 30.92% when the concentration of polymer PBAST in organic phase was 5 wt%, the concentration of PVA in inner aqueous phase was 5 wt%, the volume ratio of $W_1/O$ emulsion to outer aqueous phase was 1:4.5, and when co-surfactants that had large gap in HLB (hydrophile-lipophile balance) value were used. The bulk density of prepared hollow microsphere was 0.180 g/ml and particle size was $1.5{\sim}3\;{\mu}m$.

• Polymer(Korea)
• /
• v.33 no.3
• /
• pp.213-218
• /
• 2009

A cationic lipid emulsion containing 1,2-dioleoyl-3-trimethylammonium-propane(DOTAP), Tween80, squalene has been prepared as a gene delivery system. In order to increase the transfection efficiency of gene carrier, folate was used as the tumor-targeting ligand that was attached on PEG-DPPE. HeLa and 293 cells were used for the in vitro transfection experiment. HeLa cell is a folate-positive cell line. The mean particle sizes of polymeric lipid system and DNA/lipid complex system were 206.6 nm and 150.5 nm, respectively. The transfection efficiencies of our carriers(4:l(w:w) complex ratio)were 100 times higher than that of DOTAP only emulsion due to the targeting effect of folate.

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.65-70
• /
• 2012

Glycidyl methacrylate (GMA) was used to introduce epoxy groups on the surface of polypropylene (PP) plate, used as a substrate, through plasma-induced graft copolymerization. Emulsion polymerization was applied for graft copolymerization of GMA and was compared with conventional solution polymerization to confirm its effect. Plasma treatment conditions under one atmospheric pressure were fixed as follows; the RF power of 200 W, the treatment time of 30 sec, the Ar gas flow rate of 6 LPM, and the exposure time of treated PP samples in air of 5 min. For graft-copolymerization, GMA concentration, reaction temperature, and reaction time was optimized to maximize the grafting degree of GMA. The maximum grafting degree of GMA was obtained at the condition of 12%-GMA concentration, $90^{\circ}C$ reaction temperature, and 5 hr-reaction time. Analysis results supported that the emulsion polymerization was more effective than the solution polymerization for grafting more GMAs on the surface of PP plate under the same reaction conditions.

• Polymer(Korea)
• /
• v.34 no.4
• /
• pp.321-325
• /
• 2010

Fibroin is a biopolymer available in large quantity from silk fiber and has a long history of use as a suture proving biocompatibility. In this report, fibroin microspheres has been fabricated for biomaterial applications. W/O emulsion of regenerated fibroin droplets in a continuous phase of decane with mixed surfactants was dried to facilitate fibroin gelation and the condensed fibroin microspheres were harvested. The ratio of mixed surfactants and their proportions to decane were determined to prepare a stable W/O emulsion. A spherical form of fibroin gels was obtained from the W/O emulsion agitated at 600 rpm. Scanning electron microscopy revealed that number average sizes of the fibroin microspheres were 21.6 and 8.5 ${\mu}m$ when dried under ambient conditions or under vacuum, respectively. Tomography of the spheres revealed that their internal structures are packed or hollowed. Hollow and hemispherical forms of microspheres were also prepared by using porogen.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.119-127
• /
• 2014

The application of sulfur polymer emulsion (SPE) as an acrylate substitute for semi-rigid pavement grout was evaluated, and the performance improvement by employing PVA fibers were also evaluated. The result indicated that the filling ratio of semi-rigid pavement material decreased as the fiber content increased, but it was measured to be 92~94% in every mixing condition, which satisfies the target performance, 90%. The maximum Marshall stability value of semi-rigid pavement material was measured to be 25.4 kN, which is about 4.7 times higher than the Korean Standard required for semi-rigid pavement material, 5.0 kN. The dynamic stability evaluation of semi-rigid pavement material indicated that the resistance to deformation from the wheel tracking test was improved by an SPE substitution, and in every mixing condition, the deformation converged to a constant value after 45 minutes with the same dynamic stability of 31,500 times/mm. The strain at the flexural failure was about 0.53%, which shows superior rigidity to asphalt pavements. The examination of abrasion resistance and impact resistance showed that the loss ratio was 9.8~6.0% in every mixing condition, which indicates a good abrasion resistance. Also, when fiber content ratio was 0.3%, the impact resistance was 2.82 times higher compared to plain (i.e., when fibers were not added). In the limited range of this study, an SPE substitution ratio of 30% was found to be an optimal level considering the mechanical and durability performance. In addition, it is thought that semi-rigid pavement material with superior performance could be manufactured if fiber content ratio up to 0.3% is applied depending on the purpose of use.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.4
• /
• pp.57-65
• /
• 2013

The development of the oil refining industry has resulted in an annual 120 million tons of sulphur, which is a by-product of the desulphurization process. To exploit this abundance, the applications of sulphur must be expanded. as excellent durability of reuse of leftover sulphur which has high potential for utilization in construction materials, the study is actively in progress. Meanwhile, there has been active research on semi-rigid pavements that draw on the strengths and overcome the weaknesses of asphalt and concrete pavements. Acrylate is used to prevent cracking but involves a high cost, thus, an alternative material is required. As such, this study presents methods on the reuse of leftover sulphur and examines the engineering performance of grout containing sulfur polymer emulsion (SPE) for use in semi-rigid pavements. Our analysis shows that grout in which 30% of acrylate is replaced with SPE has superior properties in terms of time of flow and strength compared to regular grout. However, performance declined when more than 50% of acrylate was replaced by SPE, indicating that the optimum replacement level is 30%. Through SEM analysis, we found that grout with utra harding cement in this study at three hours had similar hydration properties to that of Type 1 Ordinary Portland Cement (OPC) at seven days, and maintained the properties regardless of grout containing SPE. OPC and grout with a replacement level of 30% displayed similar levels of chloride invasion resistance, whereas grout without SPE was far less resistant. Within the scope of this paper, the optimum replacement level of acrylate with SPE was found to be 30% in consideration of various properties such as time of flow, strength, and chloride invasion resistance.

• Journal of the Korean Society of Industry Convergence
• /
• v.9 no.1
• /
• pp.45-50
• /
• 2006

In order to analyse the properties of the fiber-adhesive that was used as Flocking process we synthesized quaterpolymer with the variation of the types of monomer ratio by emulsion polymerization. We characterized the properties of this adhesive: Differential Scanning Calorimeter(DSC), Thermogravimetry Analysis(TGA), Raman spectroscopy. The polymer was synthesized by changing the using amount of 2-EHAM, and then we investigated the characteristics of glass transition temperature(Tg), melting temperature(Tm), thermal stability and hydroxyl group respectively. The optimum monomer composition was 36.84% EAM, 15.79% MAM, 42.1% 2-EHAM and 5.26% AAc.

• Korea-Australia Rheology Journal
• /
• v.16 no.3
• /
• pp.153-160
• /
• 2004

Open microcellular foams having small-sized cell and good mechanical properties are desirable for many practical applications. As an effort to reduce the cell size, the microcellular foams combining viscosity improvers into the conventional formulation of styrene and water system were prepared via high internal phase emulsion polymerization. Since the material properties of foam are closely related to the solution properties of emulsion state before polymerization, the flow behavior of emulsions was investigated using a controlled stress rheometer. The yield stress and the storage modulus increased as viscosity improver concentration and agitation speed increased, due to the reduced cell size reflecting both a competition between the continuous phase viscosity and the viscosity ratio and an increase of shear force. Appreciable tendency was found between the rheological data of emulsions and the cell sizes of polymerized foams. Cell size reduction with the concentration of viscosity improver could be explained by the relation between capillary number and viscosity ratio. A correlative study for the cell size reduction with agitation speed was also attempted and the result was in a good accordance with the hydrodynamic theory.