• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1216-1218
• /
• 1997

Hydrolysis of BTDA-ODA: MPDA, PMDA-ODA, PIQ polyimides were investigated by FT-IR. The results showed that hydrolysis depends on structure of polyimide and that polyimide obtains hydrolytic stability by curing. Polyimide-aluminum interfaces were characterized by RAIR. It was concluded that imidization of the polyamic acid to polyimde was inhibited by interaction of acid groups with substrate to form aluminum carboxylate.

• Elastomers and Composites
• /
• v.58 no.1
• /
• pp.26-31
• /
• 2023

Aromatic diamine containing ortho catenation and methyl group was synthesized from 4-methyl catechol and 4-nitrobenzoyl chloride. Subsequently, a poly(amic acid) was prepared by reacting 4-methyl-1,2-phenylene bis(4-aminobenzoate) with 4,4'-hexafluoroisopropylidenediphthalic anhydride (6FDA). The resulting poly(amic acid) was transformed into a polyimide through chemical imidization. The polyimide formed was soluble in N-methyl-2-pyrrolidone (NMP) and could be cast into a flexible, transparent film. Furthermore, the polyimide exhibited a 5% weight loss at 380 ℃ in the nitrogen atmosphere.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.8
• /
• pp.866-870
• /
• 2004

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with rubbing alignment method on polyimide surfaces using plastic substrates. It was found that monodomain alignment of NLC is obtained with rubbing alignment method on polyimide surfaces using thin plastic substrates. The NLC pretilt angles on thin plastic substrates generated higher than that on glass substrate. Also, EO characteristics of the TN-LCD with a rubbed PI surface based on polymer substrate are almost the same as that of the TN-LCD with a rubbed PI surface based on glass. However, the transmittances of the TN-LCD with a rubbed PI surface based on polymer is less than that with a rubbed PI surface based on g1ass.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04a
• /
• pp.18-22
• /
• 2004

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with rubbing alignment method on polyimide surfaces using thin plastic substrates. It was found that monodomain alignment of NLC is obtained with rubbing alignment method on polyimide surfaces using thin plastic substrates. The NLC pretilt angles generated are about $3^{\circ}$ by the rubbing alignment method on thin plastic substrates, However, the pretilt angle are at about $1.7^{\circ}$ lower on the glass substrate than on thin plastic substrate. Also, EO characteristics of the TN-LCD with a rubbed PI surface based on polymer are almost the same as that of the TN-LCD with a rubbed PI surface based on glass. However, the transmittances of the TN-LCD with a rubbed PI surface based on polymer is less than that with a rubbed PI surface based on glass.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05a
• /
• pp.202-205
• /
• 2004

We investigated the electro-optical(EO) performances of the super twisted nematic liquid crystal display(STN-LCD) on the polyimide(PI) surface using polymer film. The NLC pretilt angles generated are about $18^{\circ}$ by the rubbing alignment method on thin plastic substrates. However, the pretilt angle are at about $13^{\circ}$ lower on the glass substrate than on thin plastic substrate. Monodomain alignment of the plastic STN-LCD can be observed. A stable voltage-transmittance(V-T) curve of the plastic STN-LCD was observed on the polyimide(PI) surfaces using polymer film. Also, a faster response time for the plastic STN-LCD on the polyimide(PI) surfaces using polymer film can be achieved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1095-1099
• /
• 2004

We investigated the electro-optica](EO) performances of the super twisted nematic liquid crystal display(STN-LCD) on the polyimide(PI) surface using polymer film. The NLC(Nematic Liquid Crystal) pretilt angles generated are about 18$^{\circ}$by the rubbing alignment method on thin plastic substrates. However, the pretilt angle are at about 13$^{\circ}$ lower on the glass substrate than on thin plastic substrate. Monodomain alignment of the plastic STN-LCD can be observed. A stable voltage-transmittance(V-T) curve of the plastic STN-LCD was observed on the polyimide(PI) surfaces using polymer film. Also, a faster response time for the plastic STN-LCD on the polyimide(PI) surfaces using polymer film can be achieved.

• Electronic Materials Letters
• /
• v.14 no.6
• /
• pp.749-754
• /
• 2018

Previous studies have reported on the mechanical robustness and chemical stability of flexible amorphous indium gallium zinc oxide (a-IGZO) thin-film transistors (TFTs) on plastic substrates both in flat and curved states. In this study, we investigate how the polyimide (PI) substrate affects hydrogen concentration in the a-IGZO layer, which subsequently influences the device performance and stability under bias-temperature-stress. Hydrogen increases the carrier concentration in the active layer, but it also electrically deactivates intrinsic defects depending on its concentration. The influence of hydrogen varies between the TFTs fabricated on a glass substrate to those on a PI substrate. Hydrogen concentration is 5% lower in devices on a PI substrate after annealing, which increases the hysteresis characteristics from 0.22 to 0.55 V and also the threshold voltage shift under positive bias temperature stress by 2 ${\times}$ compared to the devices on a glass substrate. Hence, the analysis and control of hydrogen flux is crucial to maintaining good device performance and stability of a-IGZO TFTs.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.1 no.1
• /
• pp.37-42
• /
• 2000

Copper thin films have been prepared by a metal organic chemical vapor deposition (MOCVD) technology on polyimide and TiN substrates. The Cu-MOCVD technology has advantages of the high deposition rate and the good step coverage compared with the conventional physical vapor deposition (PVD) technology in several industrial applications. The Cu films have been deposited with varying the experimental conditions of substrate temperatures and copper source vapor pressures. The films were annealed in a vacuum condition after the deposition, and the annealing effect on the electrical properties of the films was measured. The crystallinity and the microstructures of the films were observed by scanning electron microscopy (SEM), and the electrical resistivity was measured by 4-point probe. In the case of the Cu deposition on TiN substrate, the best electrical property of the films was measured for the samples prepared at 18$0^{\circ}C$. Very high deposition rate of the Cu film up to 250 nm/min was obtained on the polyimide substrate when the mixture of liquid and vapour precursor was used.

• Journal of Surface Science and Engineering
• /
• v.27 no.5
• /
• pp.261-272
• /
• 1994

Both Cu-Cr and Cu-Ti alloy films with different composition were prepared by dc magnetron sputtering onto polyimide substrate and their adhesion and microstructure were observed. In addition, the effect of heat treatment at $400^{\circ}C$ for 2 hours on the variation of adhesion properties and on the changess of microstructure were investigated. Cu-Cr alloy films have crystalline structure of either for or bcc phase depending on the composition of the film. However, the Cu-Ti alloy film forms fcc phase at low Ti concentration while it forms an amorphous phase as the Ti concentration in the films is increased to more than 25at.%. TEM analysis reveal that the microstructure of Cu-Cr and Cu-Ti films forms an open structure with vacant spaces. The adhesion between Cu-Cr, Cu-Ti alloy films and polyimide substrate is relatively good before the heat treatment, but is noticeably reduced after the heat treatment. In particular, the adhesion strength is significantly reduced in the Cu-Ti alloy films after the heat treatment. The reduction of adhesion strength after the heat treatment is identified to relate with the formation of oxide phases at the metal/polyimide interface by AES(Auger Electron Spectroscopy).

• Korean Chemical Engineering Research
• /
• v.51 no.2
• /
• pp.292-295
• /
• 2013

By using a simple solution based method, gold nanonetworks which are randomly distributed gold nanowires arrays were synthesized. After APTMS (3-aminopropyltrimethoxysilane) treatment, adhesion of gold nanonetworks with 10-15 nm diameters to the substrate was greatly enhanced. Density of gold nanonetworks increased with number of coating, and uniformly coated nanonetworks were connected physically and electrically. Gold nanonetworks deposited on the flexible polyimide substrate shows constant electrical conductivity for physical bending of the substrate.