• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 가을 학술발표회 논문집
• /
• pp.405-412
• /
• 1998

According to the relative stiffness between the half-space and plate or loading condition, some parts of the plate can be separated from the half-space. The finite element procedure to determine the contact area by considering the distribution of contact pressure between plate and the elastic half-space is developed. The vertical surface displacements of the elastic half-space can be obtained through the integrations of the Boussinesq's solution for a point load. The rectangular plate on the elastic half-space is modeled by the 8-node rectangular and 6-node triangular elements and the Mindlin plate theory is used in oder to consider the transverse shear effect. In this study, the contact area may be determined approximately by the analysis with rectangular elements. From this results, the mesh pattern is modified by using triangular and rectangular elements. The contact area can be determined by the new mesh pattern with a relatively sufficient accuracy.

• Nuclear Engineering and Technology
• /
• 제53권8호
• /
• pp.2464-2476
• /
• 2021

Direct-contact heat transfer of a single saturated droplet upon colliding with a heated wall in the regime of film boiling was experimentally investigated using high-resolution infrared thermometry technique. This technique provides transient local wall heat flux distributions during the entire collision period. In addition, various physical parameters relevant to the mechanistic modelling of these phenomena can be measured. The obtained results show that when single droplets dynamically collide with a heated surface during film boiling above the Leidenfrost point temperature, typically determined by droplet collision dynamics without considering thermal interactions, small spots of high heat flux due to localized wetting during the collision appear as increasing We_n. A systematic comparison revealed that existing theoretical models do not consider these observed physical phenomena and have lacks in accurately predicting the amount of direct-contact heat transfer. The necessity of developing an improved model to account for the effects of local wetting during the direct-contact heat transfer process is emphasized.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.2152_2153
• /
• 2009

In this study, the dynamic characteristic of a contact wire and pantograph suppling electrical power to high-speed trains are investigated from an electrical response point of view. To analysis power line disturbance by induced contact loss phenomenon for high speed operation, a hardware Simulator which considered contact loss between contact wire and the pantograph as well as contact wire deviation is developed. It is confirmed that a contact wire and pantograph model are necessary for studying the dynamic behavior of the pantograph system. One of the most important needs accompanied by increasing the speed of high-speed train is reduced that an arc phenomenon by loss of contact brings out EMI. In case of a high-speed train using electrical power, as comparison with diesel rolling stock, PLD(Power Line Disturbance) such as harmonic, transient voltage and current, EMI, dummy signal injection etc usually occurs. Throughout experiment, it is verified that an arc phenomenon is brought out for simulator operation and consequently conducted noise is flowed in electric circuit by power line disturbance.

• 한국안광학회지
• /
• 제10권2호
• /
• pp.127-132
• /
• 2005

칼라콘택트렌즈는 의료용으로 사용되기 시작하여 최근 들어 미용의 목적으로 그 수요가 급격히 증가하고 있는 추세이다. 칼라콘택트렌즈의 제조방법으로는 pigment application method, pigment inlay method, sandwich method, binding method 등이 있는데 현재 국내에서는 binding method가 주로 사용된다. 칼라 콘택트렌즈의 용도와 제조 방법 면에서 채색(tinted)과 착색(cosmetic)으로 크게 분류되는데 채색은 염색방식으로 널리 알려진 방법이며, 착색은 박막공법에 의해 제조된다. 이에 따라 본 해설의 목적은 칼라콘택트렌즈의 제조방법 및 방법에 따른 특성을 비교하고, 칼라콘택트렌즈의 특성을 이해하는데 도움을 주기 위함이다.

• 한국생산제조학회지
• /
• 제22권2호
• /
• pp.310-317
• /
• 2013

In this paper, the contact pressure of the wafer and polishing pad for final polishing process for 300 mm-wafer were investigated through numerical analysis using FEM tool, ANSYS. The distribution of the contact pressure is one of main parameters which affects on the flatness and surface roughness of polished wafers. Two types of polishing head, a hard type head with ceramic disk and a soft type head with air bag were considered. The effects of the deformation and initial shape of table on the contact pressure were also examined. Both heads and tables were modeled as 3D finite element model from solid model, and the material properties of polishing pads and rubber plate for the air-bag head were obtained from tensile tests. The contact pressure deviation on wafer surface was smaller with air bag head than hard type head even when the table had form errors such as convex or concave. From this 3D analysis, it could be concluded that the air-bag head has better uniformity of the contact pressure on wafer. Also, the effects of inner diameter of air bag and radial clearance between wafer and retainer were investigated as view point of contact pressure concentration on the edge of wafer.

• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.55-62
• /
• 2013

An analytical procedure to determine a proper profile of the spring rail that generates intended contact pressure distribution in the flat wiper blade is introduced. The flat wiper blade is one piece blade and subjected to pressing force at a center point. In this type of blade, contact pressure distribution in the tip of rubber strip is determined by the pressing force, the initial profile of the blade before contact and bending stiffness of the blade. Experimentally obtained bending stiffness of the blade assembly is almost identical to that of the spring rail. Principle of reciprocity has been used to define the initial profile of spring rail from the deformed profile that is assumed to be identical to the windshield glass profile. The procedure has been verified experimentally by measuring the contact pressure of the blade assembled with the spring rail designed by the procedure proposed here. Measured contact pressure distributions of the blades show good agreements with intended distributions over the entire blade span. Consequently, it can be concluded that proposed procedure has relatively good accuracy in developing the spring rail for flat blade having a specific contact pressure distribution.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.517-520
• /
• 2003

The purpose of this paper is to investigate the effect of arc current and contact velocity on the erosion of silver contact to be used in low voltage circuit breakers. The arc current range from $2kA_{rms}$ to $20kA_{rms}$. A test system allows the control of the opening velocity profiles with contact velocities up to 10m/s and also enables the synchronization of the contact opening with a point on the arc current waveform. Contact erosion is evaluated by measuring the mass change of the cathode and anode. The results show that increase the opening velocity from 2m/s to 6m/s leads to an decrease in the contact erosion. The material transfer from one electrode to another is shown to depend on the transfer charge and the opening velocity of the contacts.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집 특별세미나,특별/일반세션
• /
• pp.499-503
• /
• 2009

In this study, the dynamic characteristic of a contact wire and pantograph suppling electrical power to high-speed trains are investigated from an electrical response point of view. To analysis power line disturbance by induced contact loss phenomenon for high speed operation, a hardware Simulator which considered contact loss between contact wire and the pantograph as well as contact wire deviation is developed. It is confirmed that a contact wire and pantograph model are necessary for studying the dynamic behavior of the pantograph system. One of the most important needs accompanied by increasing the speed of high-speed train is reduced that an arc phenomenon by loss of contact brings out EMI. In case of a high-speed train using electrical power, as comparison with diesel rolling stock, PLD(Power Line Disturbance) such as harmonic, transient voltage and current, EMI, dummy signal injection etc usually occurs. Throughout experiment, it is verified that an arc phenomenon is brought out for simulator operation and consequently conducted noise is flowed in electric circuit by power line disturbance.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2007년도 춘계학술발표대회 및 제12회 신소재 심포지엄
• /
• pp.19.2-19.2
• /
• 2007

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.3-4
• /
• 2007