• 터널과지하공간
• /
• 제19권6호
• /
• pp.473-478
• /
• 2009

기존의 점하중시험기는 재하점간 중심축의 일치성에서 문제가 발생하는 경우가 존재하며 압력게이지를 통해서 시료에 가해지는 하중을 산정하기 때문에 정확성이 결여될 수 있는 단점이 있다. 본 연구는 원추판을 저항판과 함께 밀어 올리는 방식을 사용하고 지지 연마봉에 선형베어링을 장착하여 연속적으로 반복되는 시험에도 재하점의 축간 편심오차를 0.1 mm 이하로 유지한 개량형 점하중시험기를 개발하였다. 또한 반복되는 시험에서 재하점간의 거리를 자동으로 측정하고 편심오차를 확인하기 위하여 두 개의 디지털게이지를 부착하였다. 상부 원추판 끝단에 장착한 로드셀은 시료에 가해지는 순수 하중을 측정하여 압력계 방식인 기존의 점하중시험기가 가지는 단점을 보완하였다. 개발된 개량형 점하중시험기는 화성암, 편마암, 셰일에서 선택된 표준 코어시료에 대하여 총 107회의 점하중강도시험을 수행하고 품질과 성능이 검증되었다.

• 한국자동차공학회논문집
• /
• 제6권2호
• /
• pp.80-91
• /
• 1998

In this paper, the estimation of dynamic interlaminar fracture toughness on fracture mode II in CFRP(carbon fiber reinforced plastics) laminates in made. Dynamic ENF(End Notched Flexure) apparatus used in this paper is manufactured by suing Split Hopkinson Pressure Bar. The static and impact load history in the CFRP specimen is measured by using manufactured dynamic ENF tester and 3-point bending test is carried out to find the load history. Also dynamic interlaminar fracture toughness can be found by using the J integral obrained from dynamic analysis in consideration of intertia-force effect.

• 한국구조물진단유지관리공학회 논문집
• /
• 제15권1호
• /
• pp.189-197
• /
• 2011

구조실험에서 정확성과 효율성을 높이기 위해서는 적절한 실험장치를 적용하는 것은 중요한 요소이다. 특히, 대규모의 구조 실험에서 적절한 실험장치는 비용과 시간을 절감할 수 있다. 액츄에이터와 유압잭 및 UTM은 실험체의 휨 능력을 평가하는 데 일반적으로 적용되고 있다. 그러나, 대규모 실험체에서 다점 다하중 가력하중이 적용되어야 하는 경우에는 기존의 UTM 등을 이용하는 실험방법은 정확한 하중을 가력하기에 어려움이 많다. 이를 해결하기 위하여 본 연구에서는 실험결과의 정확성과 효율성을 높이기 위하여 기존의 실험장치로 조합된 새로운 방법을 개발하였다.

• 대한기계학회논문집
• /
• 제14권2호
• /
• pp.298-309
• /
• 1990

In this paper, a new method is suggested to analyze impulsive stresses at loading poing of concentrated impact load under certain impact conditions determined by impact velocity, stiffness of plate and mass of impact body, etc. The impulsive stresses are analyzed by using the three dimensional dynamic theory of elasticity so as to analytically clarify the generation phenomenon of cone crack at the impact fracture of fragile materials (to be discussed if the second paper). The Lagrange's plate theory and Hertz's law of contact theory are used for the analysis of impact load, and the approximate equation of impact load is suggested to analyze the impulsive stresses at the impact point to decide the ranage of impact load factor. When impact load factors are over and under 0.263, approximate equations are suggested to be F(t)=Aexp(-Bt)sinCt and F(t)=Aexp(-bt) {1-exp(Ct)} respectively. Also, the inverse Laplace transformation is done by using the F.F.T.(fast fourier transform) algorithm. And in order to clarity the validity of stress analysis method, experiments on strain fluctuation at impact point are performed on a supported square glass plate. Finally, these analytical results are shown to be in close agreement with experimental results.

• 설비공학논문집
• /
• 제14권3호
• /
• pp.240-246
• /
• 2002

Bypass air conditioning systems are divided into three types; an outdoor air bypass, a mixed air bypass and a return air bypass system. What makes the return air by pass system more effective is that it directs all of moist outdoor air through the cooling coil. The bypass air conditioning system can maintain indoor R.H (Relative Humidity) less than a conventional CAV (Constant Air Volume) air conditioning system by adjusting face and bypass dampers at part load. When a design sensible load (the ratio of sensible load to total sensible load) is 70 percent (at this time, RSHF (Room Sensible Heat Factor) . 0.7), indoor R.H was maintained 59 percent by the return air bypass system, but 65 percent by the conventional CAV air conditioning system (valve control system). The bypass air conditioning system can also improve IAQ (Indoor Air Quality) in many buildings where the number of air change is high.

• 전기학회논문지P
• /
• 제61권4호
• /
• pp.199-205
• /
• 2012

This paper propose a improved parameter estimations of five-phase squirrel-cage induction motor(IM) for speed control system on field oriented control(FOC). In order to high performance control of ac the motors using a FOC and DTC(direct torque control) algorithm, there are required precise motor parameters for slip calculation, flux observer, controller gain, rotor position and speed estimation, and so on. We are suggest a estimation method of the motor parameters that developing five-phase squirrel-cage IM have a stator of concentrated winding for experimental. There are results of stator winding test, no-load test, locked rotor test, and obtained equivalent circuits using manufactured experimental apparatus. For presenting the superior performance of the speed control system in adapted the parameters, experimental results are presented using a 32-bit fixed point TMS320F2812 DSP with 1.5[KW] IM.

• Structural Engineering and Mechanics
• /
• 제55권1호
• /
• pp.137-160
• /
• 2015

The one-way (two-way) flexural strength of RCC prisms (circular slabs) reinforced with glass fiber textiles is addressed. To this end, alkaline-resistant glass fiber textiles with three surface weights were used in the composite, the matrix concrete was designed with zero/nonzero slump, and the textiles were used with/without an intermediate layer provided by epoxy resin and sand mortar. Prisms were tested under a four-point loading apparatus and circular slabs were placed on simple supports under a central load. Effects of the amount and geometry of reinforcement, matrix workability, and the intermediate layer on the ultimate load and deflection were investigated. Results revealed that, with a specific reinforcement amount, there is an optimum textile tex for each case, depending on the matrix mix design and the presence of intermediate layer. Similar results were obtained in one-way and two-way bending tests.

• 전기의세계
• /
• 제23권4호
• /
• pp.60-65
• /
• 1974

This paper is to study on the pilot work of bi-directional S.C.R. power converter adopted by the method of diode-bridge type circuit. This apparatus acts as a converter when it is used in convering 3-phase a.c source to d.c output, and it can be used as an inverter which recovering surplus d.c power to a.c source when d.c load become active to cause the induced voltage higher than the presetted point of d.c output voltage. At the same time, its d.c voltage varies continuously in the presetted range of positive and/or negative polarity. As a result of test, the AC/DC bi-directional power converter represents maximum converting efficiency of 91% and power factor of 0.98. Furthermore, this converter also can be applied as a cycleconverter by varying the period of gate triggering signal.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.525-529
• /
• 1999

A cone shape drum polisher was developed to make up for the demerits of conventional CMP apparatus. The developed equipment has several superiorities. First of all, it can achieve uniform velocity profile on all the contact line because of its shape and easy to control the amount of slurry at the position of use. The whole area of wafer surface is exposed to the visual area except the contact line between wafer and drum, hence we can detect polishing end point more easily than any other polishing equipments. Also it has additional merits such as small foot print and polishing load. Polishing characteristics were investigated by developed equipment.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.355-357
• /
• 2014

The usefulness of unsteady combustion was experimentally investigated using confined premixed flames stabilized by a rearward-facing step. For this purpose, apparatus of forced pulsating mixture supply, which could be modulated its amplitude and frequency, was designed. The unsteady combustion used in this experiment plays an important role in controlling self-excited combustion oscillations and furthermore it exhibits desirable performance, from a practical point of view, such as high load combustion and reduction of pollutant emission like nitric oxide.