• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.869-872
• /
• 2003

The thermal contamination of the Younggwang coastal marine ecosystem has been investigated using space borne thermal infrared data acquired over the period 1985-2003 by the Landsat and NOAA satellites. The analysis of AVHRR data brought out the general pattern and extension of thermal plume while TM data yielded more accurate information about the plume shape, dimension, dispersion direction etc. The examination of sea surface temperature (SST) computed from these images clearly indicates that the thermal plume extends 70 to100km southward during summer and 50 to70km northwestward during winter monsoons. The maximum plume temperature was 29$^{\circ}C$ in summer and 12$^{\circ}C$ in winter. The comparative analysis shows that the temperature retrieved from TM is slightly higher (1.8$^{\circ}C$, 3$^{\circ}C$ and 2.2$^{\circ}C$ for the images of 98/11/10, 99/05/05 and 99/05/21 respectively) than those derived from AVHRR data. The correlation coefficient between the TM-derived SST and AVHRR-derived SST was 0.72.

• Wind and Structures
• /
• v.27 no.6
• /
• pp.417-430
• /
• 2018

The concentration fields in the proximities of a local gas emission source are experimentally analyzed in several combinations of wind incidences and source emissions. These conditions are determined by the plume buoyancy, emission velocity and incident flow wind speed. Concentration measurements are performed by an aspirating probe in a boundary layer wind tunnel. The analysis included the mean concentration values and the intensity of concentration fluctuations in a neutral atmospheric boundary layer flow. Different configurations are tested: an isolated stack in a homogeneous terrain and a stack with a bluff body in close proximity, located windward and leeward from the emission source. The experimental mean concentration values are contrasted with Gaussian profiles and the dilution factor is analyzed with respect to the empirical curves of the minimum dilution. Finally, a study on the plume intermittency is performed in a cross-sectional plane near the emission source. It is possible to highlight the following observations: a) plume vertical asymmetry in the case of an isolated emission source, b) significant differences in the dispersion process related to the relative location of the emission source and bluff body effects, and c) different probabilistic behavior of the concentration fluctuation data in a cross-sectional measurement plane inside the plume.

• Aerospace Engineering and Technology
• /
• v.13 no.1
• /
• pp.63-69
• /
• 2014

The oxidizer-rich preburner's combustion tests were fulfilled in the development process of staged combustion cycle rocket engines. The exhaust plume from an oxidizer-rich preburner is relatively transparent because combustion takes place in oxidizer rich state. During hot fire tests a still and infrared images were captured to visualize the plume structure, temperature distribution and so on. In addition, the exhaust plume was numerically investigated to figure out the detailed characteristics. The combustion was not considered for the numerical modeling, but the mixing of exhaust plume with circumstantial air was modeled by species transport model with several turbulence models. The inner structure of plume was configured out by the comparison of numerical results with experimental results, and the validity of applied numerical models was verified.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.06a
• /
• pp.368-376
• /
• 2004

The estimation of the diffusion coefficients of the Gaussian plume model and the release rate by assimilation of tracer-gas measurements on Younggwang site was tested. Diffusion coefficients were modified by linear programming of both the measurements and the simulated using the Gaussian plume model. The application of the modified diffusion coefficients improved the prediction ability of the Gaussian plume model on both 3 km and 8 km arc lines. And, the release rate of tracer gas was estimated using least squares method. The optimal source rate was estimated by minimizing the errors between the measured concentrations and the computed ones by the Gaussian plume model. The obtained release rate showed a good agreement with the real release rate of the Younggwang experiment in 24%.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.4
• /
• pp.24-31
• /
• 2005

A plused laser ablation deposition(PLAD) technique has been used for producing fine particle as well as thin film at relatively low substrate temperatures. However, in order to manufacture and evaluate such materials in detail, motions of plume particles generated by laser ablation have to be understood and interactions between the particles by ablation and gas plasma have to be clarified. Therefore this paper was focused on the understanding of plume motion in laser ablation assisted by hi plasmas at 100[mTorr]. One-dimensional hybrid model consisting of fluid and particle models was developed and three kinds of plume particles which are carbon atom(C), $ion(C^+)$ and electron were considered in the calculation of particle method. It was obtained that ablated $C^+$ was electrically captured in Ar plasmas by strong electric field(E). The difference between motions of the ablated electrons and $C^+$ made E strong and the collisional processes active. The energies of plume particles were investigated on a substrate surface. In addition the plume motion in Ar gas was also calculated and discussed.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.5 no.4
• /
• pp.296-301
• /
• 1993

A hydrodynamic solution for the lateral spreading of a river plume which was developed by assuming a Gaussian distribution of density difference between a turbulent jet river plume and ambient salt water is verified by the field data in the Nakdong river plume. Effect of the river plume on the transport of fine-grained suspended sediment at the Nakdong Estuary is also examined. The analysis of fold data showed a reasonably good correspondence with the theoretical solution adopted in this work Therefore, the hydrodynamic solution can be used as a useful tool in dealing with the lateral spreading of a river plume. The density stratification due to the existence of a river plume seems to cause a retarded settling of the suspended sediments in the water column. and thus a farther transport of the fine sediment is expected than in the normal steady flow.

• Journal of Korean Society for Atmospheric Environment
• /
• v.23 no.4
• /
• pp.449-456
• /
• 2007

Dispersion coefficient preprocessing schemes have been examined to improve plume dispersion model performance in complex coastal areas. The performances of various schemes for constructing the sigma correction order were evaluated through estimations of statistical measures, such as bias, gross error, R, FB, NMSE, within FAC2, MG, VG, IOA, UAPC and MRE. This was undertaken for the results of dispersion modeling, which applied each scheme. Environmental factors such as sampling time, surface roughness, plume rising, plume height and terrain rolling were considered in this study. Gaussian plume dispersion model was used to calculate 1 hr $SO_2$ concentration 4 km downwind from a power plant in Boryeung coastal area. Here, measured data for January to December of 2002 were obtained so that modelling results could be compared. To compare the performances between various schemes, integrated scores of statistical measures were obtained by giving weights for each measure and then summing each score. This was done because each statistical measure has its own function and criteria; as a result, no measure can be taken as a sole index indicative of the performance level for each modeling scheme. The best preprocessing scheme was discerned using the step-wise method. The most significant factor influencing the magnitude of real dispersion coefficients appeared to be sampling time. A second significant factor appeared to be surface roughness, with the rolling terrain being the least significant for elevated sources in a gently rolling terrain. The best sequence of correcting the sigma from P-G scheme was found to be the combination of (1) sampling time, (2) surface roughness, (3) plume rising, (4) plume height, and (5) terrain rolling.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.54-61
• /
• 2014

In this study, a plume exhausted from rocket nozzle is investigated by using an unstructured 2-dimensional axisymmetirc DSMC code at various altitude. The small back-pressure to total-pressure ratio($P_b/P_o$) and large $P_b/P_o$ represent low and high altitude condition, respectively. At low altitude, the plume shows a typical complicated structure (e.g. Mach disk) of underexpanded jet while the high altitude plume experiences plain expansion. The various features of exhaust plume is discussed including density, translational/rotational temperature, Mach number and Knudsen number. The results shows that even at 20 km altitude where the freestream Knudsen number is small as $1.5{\times}10^{-5}$, the transitional and rarefied flow regimes can occur locally within the plume. It confirms the necessity of DSMC computation at low altitude.

• Journal of the Korean Society of Safety
• /
• v.37 no.6
• /
• pp.166-173
• /
• 2022

A variety of input parameters are taken into consideration while performing a Level 3 PSA. Some parameters related to plume segments, spatial grids, and particle size distribution have flexible input formats. Fine modeling performed by splitting a number of segments or grids may enhance the accuracy of analysis but is time-consuming. Analysis speed is highly important because a considerably large number of calculations is required to handle Level 2 PSA scenarios for a single-unit or multi-unit Level 3 PSA. This study developed a sensitivity analysis supporting interface called MACCSsense to compare the results of the trials of plume segmentation with the results of the base case to determine its impact (in terms of time and accuracy) and to support the development of a modeling approach, which saves calculation time and improves accuracy. MACCSense is an automation tool that uses a large amount of plume segmentation analysis results obtained from MUST Converter and Mr. Manager developed by KAERI to generate a sensitivity report that includes impact (time and accuracy) by comparing them with the base-case result. In this study, various plume segmentation approaches were investigated, and both the accuracy and speed of offsite consequence analysis were evaluated using MACCS as a consequence analysis tool. A simultaneous evaluation revealed that execution time can be reduced using multi-threading. In addition, this study can serve as a framework for the development of a modeling strategy for plume segmentation in order to perform accurate and fast offsite consequence analyses.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.8 no.4
• /
• pp.305-313
• /
• 1996

CTD measurements were conducted in the Nakdong estuary on the several sections or along-plume and cross-plume directions in 1993 and 1994. Internal Froude number Fi=0.22-0.35 in ebb tides and 0.14 in flood tides suggest that Nakdong river plume may go farther seawards in the along-plume direction with little mixing with the adjacent sea water after the construction of Nakdong river barrier. From Dadae-Po to Gaduk-Do section of cross-plume direction, three cores of low salinity were found. The main plume outflows from the newly made channel by cutting Ulsuk-Do after the construction of barrier. The low salinity core found near Gaduk-Do is the plume patch advected by tidal currents. Rossby deformation radius varied with the tidal cycle so that Coriolis effect is strengthened in flood tides to deepen the isohalines westwards to the Gaduk-Do site. Internal wavelike shape was found in the section of cross-plume direction during ebb tides. Richardson number of the section suggests the possibility of forming internal wave but more precise observations are necessary.