• Progress in Superconductivity and Cryogenics
• /
• v.20 no.4
• /
• pp.26-30
• /
• 2018

The turn-to-turn contact resistance of 2G high temperature superconducting (HTS) coils with metal insulation (MI) is closely related to the stability of the coils, current charging rate and delay time [1]. MI coils were fabricated using five kinds of metal tapes such as aluminum (Al) tape, brass tape, stainless steel (SS) tape, copper (Cu)-plated tape and one-sided Cu-plated SS tape. The turn-to-turn contact surface resistances of co-winding model coils using Al tape, brass tape, and SS tape were 342.6, 343.6 and $724.8{\mu}{\Omega}{\cdot}cm^2$, respectively. The turn-to-turn contact resistance of the model coil using the one-sided Cu-plated SS tape was $ 248.8{\mu}{\Omega}{\cdot}cm^2$, which was lower than that of Al and brass tape. Al or brass tape can be used to reduce contact resistance and improve the stability of the coil. Considering strength, SS tape is recommended. For strength and low contact resistance, SS tape with copper plating on one side can be used.

• Journal of Veterinary Clinics
• /
• v.40 no.5
• /
• pp.323-329
• /
• 2023

Peripheral blood-derived mesenchymal stem cells (PB-MSCs) have shown promise in cell-based therapy, as they can be harvested with ease through minimally invasive procedures. This study aimed to isolate PB-MSCs from foals and mares and to compare the proliferation and cellular characteristics of the PB-MSCs between the two groups. Six pairs of mares and their foals were used in this study. MSCs were isolated from PB by direct plating in a tissue culture medium, and cell proliferation (population doubling time [PDT], and colony-forming unit-fibroblast assay [CFU-F]), and characterization (morphology, plastic adhesiveness, colony formation, trilineage differentiation) were examined. There was no significant difference in the PB-MSC yield, CFU-F, and PDT between the mares and foals. PB-MSCs from both mares and foals showed typical MSC characteristics in terms of spindle-shaped morphology, plastic adhesive properties, formation of colonies, trilineage differentiation. These results suggest that PB-MSCs isolated from horses, both adult horses, and foals, can be used for equine cell-based therapy.

• Clinics in Shoulder and Elbow
• /
• v.11 no.2
• /
• pp.177-184
• /
• 2008

Purpose: The purpose of this study was to evaluate the results of eight cases of coronoid process fractures that were fixed with a plate. Materials and Methods: Eight coronoid process fractures were treated by plating and these cases were reviewed retrospectively. Six patients were men and two were women. The average age was 41 years (range: 22-79) at the time of injury. According to Regan's classification, there were five type 2 and three type 3. According to O'Driscoll's classification, there were five anteromedial type and three base type. Open reduction and internal fixation with a plate were performed through a medial approach by splitting of the two heads of the flexor carpi ulnaris. The patients were follow-up for a mean of 15.8 months (range: 6-25). We evaluated the clinical outcomes with using the Mayo Elbow Performance Score. Results: The average active motion of the elbow joint was $120^{\circ}$. The average Mayo Elbow Performance Score was 86.9. There were 5 excellent results, 1 good result and 2 fair results. Summary: Plating through a medial approach of the elbow provided stable fixation and satisfactory union for treating displaced coronoid process fractures with the unstable elbow.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.88-93
• /
• 2017

It is important to develop a simple method oftuning localized surface plasmon resonance(LSPR) properties, due to their numerous applications. In addition, the careful examination of the shape, size and combination of metal nanoparticles is useful for understanding the relation between the LSPR properties and metal nanostructures. This article describes the dependence of theLSPR properties on the arrays of metal nanoparticles obtained from a block copolymer(BCP) micellar thin film. Firstly, two different Au nanostructures, having a dot and ring shape, were fabricated using conventional block copolymer micelle lithography. Then, Ag was plated on the Au nanostructures through the silver mirror reaction technique to obtain Au/Ag bimetallic nanostructures. During the production of these metallic nanostructures, the processing factors, such as the pre-treatment by ethanol, silver mirror reaction time and removal or not of the BCP, were varied. Once the Au nanoparticles were synthesized, Ag was properly plated on the Au, providing two distinguishable characteristic plasmonic bands at around 525nm for Au and around 420nm for Ag, as confirmed bythe UV-vis measurements. However, when a small amount of Au seed nanoparticles, which accelerate the Ag plating speed,was formed by usinga block copolymer with a relatively highmolecular weight, all of the Au surfaces were fully covered by Ag during the silver mirror reaction, showing only the characteristic peak for Ag at around 420nm. The Ag plating technique on Au nanoparticles pre-synthesized from a block copolymer is useful to study the LSPR properties carefully.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.3
• /
• pp.79-84
• /
• 2010

Formation of TSV (Through-Si-Via) with an Au seed layer and Cu filling to the via, simplification of bumping process for three dimensional stacking of Si dice were investigated. In order to produce the via holes, the Si wafer was etched by a DRIE (Deep Reactive Ion Etching) process using $SF_6$ and $C_4F_8$ plasmas alternately. The vias were 40 ${\mu}m$ in diameter, 80 ${\mu}m$ in depth, and were produced by etching for 1.92 ks. On the via side wall, a dielectric layer of $SiO_2$ was formed by thermal oxidation, and an adhesion layer of Ti, and a seed layer of Au were applied by sputtering. Electroplating with pulsed DC was applied to fill the via holes with Cu. The plating condition was at a forward pulse current density of 1000 mA/$dm^2$ for 5 s and a reverse pulse current density of 190 mA/$dm^2$ for 25 s. By using these parameters, sound Cu filling was obtained in the vias with a total plating time of 57.6 ks. Sn bumping was performed on the Cu plugs without lithography process. The bumps were produced on the Si die successfully by the simplified process without serious defect.

• Membrane Journal
• /
• v.28 no.4
• /
• pp.252-259
• /
• 2018

An acidic, real metal-plating wastewater was treated by a fluidized bed membrane reactor introduced with granular activated carbon (GAC) as fluidized media. With GAC fluidization, there was no increase in suction pressure with time at each flux set-point applied. At neutral solution pH, much less fouling rate was observed than acidic pH under GAC fluidization. Higher solution pH resulted in the increase in particle size in metal-finishing wastewater, thus producing a less dense cake structure on membrane. More than 95% of chemical oxygen demand was observed from the fluidized bed membrane reactor under GAC fluidization. Total suspended solid concentration in membrane permeate was near zero. At the raw wastewater pH, no removal of copper and chromium by the fluidized bed membrane reactor was observed. As the pH was increased to 7.0, removal efficiency of copper and chromium was increased considerably to 99 and 94%, respectively. Regardless of solution pH tested, more than 95% of cyanide was removed possibly due to the strong adsorption of organic-cyanide complex on GAC in fluidized bed membrane reactor.

• Applied Chemistry for Engineering
• /
• v.23 no.3
• /
• pp.313-319
• /
• 2012

In this work, the electroplating of copper was introduced on PAN-based carbon fibers for the enhancement of mechanical interfacial strength of carbon fibers-reinforced composites. The surface properties of carbon fibers were determined by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and contact angle measurements. Its mechanical interfacial properties of the composites were studied by interlaminar shear strength (ILSS) and critical stress intensity factor ($K_{IC}$). From the results, it was found that the mechanical interfacial properties of Cu-plated carbon fibers-reinforced composites (Cu-CFRPs) enhanced with increasing the Cu plating time, Cu content and COOH group up to Cu-CFRP-30. However, the mechanical interfacial properties of the Cu-CFRPs decreased dramatically in the excessively Cu-plated CFRPs sample. In conclusion, the presence of Cu particles on carbon fiber surfaces can be a key factor to determine the mechanical interfacial properties of the Cu-CFRPs, but the excessive Cu content can lead the failure due to the interfacial separation between fibers and matrices in this system.

• 월간산업보건
• /
• s.5
• /
• pp.4-15
• /
• 1988

In order to proffer the fundamental data for the better working environment and the effective establishment of hearing conservation program on workers exposed to industrial noise, author assessed noise levels on the 42 noisy processes among 84 manufactures of 9 industries and measured noise gearing loss by the type of industries on 3,104 workers at these noisy processes from March, 1986 to Februry, 1987. The results were summarized as follows: 1. The averge of A-weight sound level of 23 processes(54.8%) and the avergae of sound level at each octave band of 14 processes(33.3%) exceeded the permissible exposure limits in 8 hours per day. 2. The noise level was the highest in process of cocking of ship building(109.1dBA), and followed by plating of steel rolling(104.3dBA), rivet of manufacture of motor vehicles(102.5dBA), shot of ship building(98.5dBA), aciding(95.7BA) and steel tubing(95.0dBA) of steel rolling, weaving of textiles(95.0dBA). 3. The permissible exposure time for the average of sound level at each octave band was only 30 minutes in the process of cocking of ship building, plating of steel rolling and rivet of manufacture of motor vehicles. 4. As a result of audiometric examination in 3,104 workers, the rate of hearing loss over 50dB at 4,000Hz was 7.3%(227 workers) and the rate of hearing loss over 41dB at 60average method was 2.9%(89 workers). 5. The prevalence of occupational hearing loss in ship building and manufacture of motor vehicle was 5.2% and it was the highest among prevalence of these 9 industries. 6. As a result of this suvery, the noise control and gearing conservation program were required especially in the industry of ship building and manufacture of motor vehicle.

• Resources Recycling
• /
• v.26 no.4
• /
• pp.88-94
• /
• 2017

The recovery of gold in cyclone type electrolytic cell was conducted from solution for stripping gold of PCB by cyanide. The electrolytic recovery behaviors of gold was investigated by reaction time and addition of electrolytic sodium hypochlorite (NaOCl) and gold plating additive (KG-120). Because the electrolysis generated NaOCl reacted with the cyanide in the leachate by alkaline chlorination, more than 99% of the cyanide was removed at a $NaOCl(g)/CN^-(g)$ ratio of 1.0. When NaOCl was added during the recovery of the gold from cyanide leachate in the cyclone electrolytic cell, the recovery of gold was 98% at the ratio of $NaOCl(g)/CN^-(g)$ from 0.5 to 2.5 in 480 minutes and decreased rapidly over the ratio of 3.0. Gold was recovered more than 99% by adding 1.5 and 4.5%(v/v) of KG-120 with NaOCl in 480 minutes. In particular, when the concentration of KG-120 was 3.5 and 4.5%(v/v), more than 96% of gold was recovered within 240 minutes and the initial recovery rate was relatively faster. The optimum concentration of KG-120 is 3.5%(v/v) considering the economic feasibility and efficiency.

• Applied Chemistry for Engineering
• /
• v.22 no.6
• /
• pp.672-678
• /
• 2011

In this work, carbon fibers were electrolessly Ni-plated in order to investigate the effect of metal plating on the electromagnetic shielding effectiveness (EMI-SE) of Ni-coated carbon fibers-reinforced epoxy matrix composites. The surfaces of carbon fibers were characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). Electric resistance of the composites was tested using a 4-point-probe electric resistivity tester. The EMI-SE of the composites was evaluated by means of the reflection and adsorption methods. From the results, it was found that the EMI-SE of the composites enhanced with increasing Ni plating time and content. In high frequency region, the EMI-SE didn't show further increasing with high Ni content (Ni-CF 10 min) compared to the Ni-CF 5 min sample. In conclusion, Ni content on the carbon fibers can be a key factor to determine the EMI-SE of the composites, but there can be an optimized metal content at a specific electromagnetic frequency region in this system.