• 한국강구조학회 논문집
• /
• 제15권3호
• /
• pp.261-269
• /
• 2003

편심브레이스골조의 설계에서 가장 중요한 인자는 링크보의 길이이다. 링크보의 길이에 따라 편심브레이스골조의 거동과 파괴메카니즘이 결정된다. 링크보의 길이가 짧아져 전단력에 의해 소성화되면 중심브레이스골조와 대등한 수평방향강성과 모멘트 연성골조의 연성을 동시에 확보할 수 있다. 또한 링크보의 길이가 길어지게 되면 링크보는 모멘트에 의해 소성화 되어 연성적인 거동을 확보할 수 없게 된다. 근래에 이르러 건축계획적인 측면에서는 링크보의 길이가 길어지는 것이 입면 및 단면계획이 용이하며, 그 필요성이 증대되고 있지만, 모멘트 링크에 대한 기존의 연구가 많이 수행되어 있지 않으며, 이와 관련된 자료가 부족한 실정이다. 본 연구에서는 실험을 통해 다양한 접합디테일을 가진 모멘트링크보의 거동을 규명하고 모멘트링크보의 거동을 개선시킬 수 있는 접합디테일을 제시하고자 한다. 4개의 접합 디테일을 가진 총 16개의 실험체를 계획하여 이력거동 실험을 수행하였다.

• Steel and Composite Structures
• /
• 제11권1호
• /
• pp.1-19
• /
• 2011

The introduction of the Eurocodes makes plastic design criteria available also for composite bridges, leading to more economical solutions compared with previous elastic design rules. Particularly for refurbishment old bridges with higher actual traffic loads, up to date outside the scope of the Eurocodes, strengthening should therefore be avoidable or at least be necessary only to a minor extent. For bridges with smaller spans and compact cross sections, the plastic load bearing capacity is clearly justified. In this work, however, the focus is placed on long span continuous composite bridges with deep, longitudinally stiffened girders, susceptible to local buckling. In a first step, the elastic - plastic cross section capacity of the main girder in bending is studied as an isolated case, based on high preloads acting on the steel girder only, due to the common assembling procedure without scaffolding. In a second step, the effects on the whole structure are studied, because utilising the plastic section capacity at midspan leads to a redistribution of internal forces to the supports. Based on the comprehensive study of an old, actual strengthened composite bridge, some limitations for plastic design are identified. Moreover, fully plastic design will sometimes need additional global analysis. Practical recommendations are given for design purposes.

• 한국강구조학회 논문집
• /
• 제15권5호통권66호
• /
• pp.531-539
• /
• 2003

노스리지 지진 발생시 구조체 손상이 발생했던 현장용접 모멘트골조와 달리 기둥-보 브라켓형식의 모멘트골조에는 지진의 영향을 조정하고 감소시키는 도구(tool)가 바로 보에 이음부(splice)이다. 지진발생 중에 보의 이음부는 연성의 퓨즈(fuse)로서 작용할 수 있고, 골조에 발생할 수 있는 흼모멘트를 포함한 힘의 크기를 제한할 수 있다. 국내에서는 모멘트 골조의 대부분이 기둥-보 브라켓 형식으로 이루어진다. 본 논문에서는 이음하지 않은 H형강보를 제작하여 단순가력 실험을 수행하였고, 고력볼트를 이용하여 전강도설계된 실물실험체와 플랜지볼트 열수를 각각 75%, 50% 및 0%로 줄여서 이음부를 제작한 H형강 보를 단순가력 실험을 수행하였다. 이들 실험을 통해 기둥-보 브라켓형식의 모멘트 골조에서 보의 이음부(Beam Splice)가 악보(Week Beam)의 임계위치(Critical Point)로서 작용할 수 있는 가능성을 타진하고자 하는 연구에 기초자료를 제공하는 것이 본 연구의 목적이다.

• Steel and Composite Structures
• /
• 제18권4호
• /
• pp.873-887
• /
• 2015

The continuous composite I-girder should have a sufficient rotation capacity (or ductility) to redistribute the negative bending moment into an adjacent positive bending moment region. However, it is generally known that the ductility of the high strength steel is smaller than that of conventional steel, and application of high strength steel can cause ductility problems in a negative moment region of the I-girder. In this study, moment redistribution of the continuous composite I-girder with high strength steel was studied, where high strength steel with yield stress of 690 MPa was considered (the ultimate stress of the steel was 800 MPa). The available and required rotation capacity of the continuous composite I-girder with high strength steel was firstly derived based on the stress-strain curve of high strength steel and plastic analysis, respectively. A large scale test and a series of non-linear finite element analysis for the continuous composite I-girder with high strength steel were then conducted to examine the effectiveness of proposed models and to investigate the effect of high strength steel on the inelastic behavior of the negative bending moment region of the continuous composite I-girder with high strength steel. Finally, it can be found that the proposed equations provided good estimation of the requited and available rotation capacity of the continuous composite I-girder with high strength steel.

• 전산구조공학
• /
• 제23권3호
• /
• pp.69-74
• /
• 2010

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.688-691
• /
• 2004

This study summarizes results of a research project aimed at investigating the inelastic rotation capacity of beam-column joints of reinforced concrete moment frames. A total of 28 specimens were classified as special moment frame connections based on the design and detailing requirements in the ACI 318-99 provisions. Then, the acceptance criteria, originally defined for steel moment frame connections in the AISC-97 Seismic Provisions, were used to evaluate the joint connections of concrete moment frames. Twenty seven out of 28 test specimens that satisfy the design requirements for special moment frame structures provided sufficient strength and are ductile up to a plastic rotation of $3\%$ without any major degradation in strength.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.553-558
• /
• 1999

As a process of development of composite beam-column connection system, structural tests have been conducted to verify moment resisting performance of the system. The tests have been proceeded by two steps, the first being welding performance test of the steel connection rod and stiffners, and the second overall moment resisting capacity of the fuly assembled system. Ten welding test specimens and four prototype specimens have been used in the test. Good structural performance of welding test specimens has been observed without any single welding failure, and sufficient moment resisting capacity has been proved from the overall performance test, with the moment magnitude in excess of the calculated plastic moment.

• Steel and Composite Structures
• /
• 제28권6호
• /
• pp.767-778
• /
• 2018

The purpose of this study is to investigate how a fully restrained bolted beam splice affects the connection behavior as a column-tree connection in steel special moment frames under cyclic loading when located within the plastic hinge zone. The impacts of this attachment in protected zone are observed by using nonlinear finite element analyses. This type of splice connection is designed as slip-critical connection and thereby, the possible effects of slippage of the bolts due to a possible loss of pretension in the bolts are also investigated. The 3D models with solid elements that have been developed includes three types of connections which are the connection having fully restrained beam splice located in the plastic hinge location, the connection having fully restrained beam splice located out of the plastic hinge and the connection without beam splice. All connection models satisfied the requirement for the special moment frame connections providing sufficient flexural resistance, determined at column face stated in AISC 341-16. In the connection model having fully restrained beam splice located in the plastic hinge, due to the pretension loss in the bolts, the friction force on the contact surfaces is exceeded, resulting in a relative slip. The reduction in the energy dissipation capacity of the connection is observed to be insignificant. The possibility of the crack occurrence around the bolt holes closest to the column face is found to be higher for the splice connection within the protected zone.

• 콘크리트학회지
• /
• 제10권4호
• /
• pp.93-100
• /
• 1998

본 논문은 고성능 철근콘크리트 보의 휨강성, 소성힌지 길이 및 소성힌지의 회전능력에 관한 연구이다. 실험은 철근비, 콘크리트 강도 및 하중 재하형태(1점가력과 2점가력)를 변수로 하여 총 15개의 철근콘크리트 단순보에 대하여 행하여 졌다. 콘크리트의 실린더 압축강도가 700kg/${cm}^2$, 슬럼프 20~25 cm 및 슬럼프 플로우가 60~70cm인 고성능 철근콘크리트 및 보통 강도 철근콘크리트 단순보의 휨실험결과, 본 실험의 경우에 고성능 철근콘크리트 보의 극한 곡률을 구할 때는 ${\varepsilon}_{cu}=0.0047$의 값을 사용할 수 있는 것으로 나타났다. 고성능 철근콘크리트 단순보의 휨강성을 평가하기 위해 유효단면 2차 모멘트를 구하는 식과 고성능콘크리트 단순보에 2점 하중을 가하는 경우 등가 소성힌지 길이를 구하는 식이 본 실험의 경우에 대해서 제시되었다. 극한 모멘트 상태에서 이러한 식을 사용하여 구한 처짐값은 실험값과 비교적 일치하게 나타났다.

• 대한조선학회논문집
• /
• 제47권6호
• /
• pp.843-849
• /
• 2010

This paper presents definition of symmetry of a ship section where three symmetries are proposed: material, geometric, and load symmetries. Precise terminologies of centroid, moment plane, and neutral axis plane are also defined. It is suggested that force vector equilibrium as well as force equilibrium are necessary condition to determine new position of neutral axis due to translational and rotational mobility. It is also stated that new reference datum of ENMP(elastic neutral moment plane), PNMP(fully plastic moment plane), ENAP(elastic neutral axis plane), and INAP(inelastic neutral moment plane) are required to define asymmetric section properties such as second moment of area, elastic section modulus, yield moment, fully plastic moment, and ultimate moment. Since collision-induced damage and flooding-induced biaxial bending moment produce typical asymmetry of section, the section properties are calculated for a typical VLCC. Geometry asymmetry is determined from ABS and DNV rules and two moment planes of 0/30 degs are assumed for load asymmetry. It is proved that the property reduction ratios directly calculated from second moment of area are usually larger than area reduction ratio. Reduction ratio of ultimate moment capacity shows almost linearly proportional to area reduction ratio. Mobility of elastic and inelastic neutral axis planes is visually provided.