• 대한금속재료학회지
• /
• 제49권2호
• /
• pp.112-120
• /
• 2011

The out-of-phase thermo-mechanical fatigue (OP TMF) in a <001> oriented single crystal nickel-based superalloy CMSX-4 has been studied. OP TMF life was less than a half of low cycle fatigue(LCF) life in spite of a small hysteresis loop area of OP TMF compared to that of LCF. The failure was caused by the initiation of a crack at the oxide-layered surface followed by its planar growth along the <100> ${\gamma}$ channel in both LCF and OP TMF. However, deformation twins appeared near the major crack of OP TMF. The multiple groups of parallel twin plates on {111} planes provided a preferential path for crack propagation, which caused a significant decrease in OP TMF life. Additionally, the analysis on the surface crack morphology revealed that the tensile strain at the minimum temperature of OP TMF was found to accelerate the crack propagation.

• 자원환경지질
• /
• 제41권6호
• /
• pp.763-771
• /
• 2008

불확실성은 사면의 안정성을 해석하는 과정에서 특성자료의 부족이나 지질공학적 특성의 공간적 변동성 등의 원인으로 포함되며 따라서 불확실성으로 인해 변수들의 정확한 값을 획득하기 힘들게 된다 이러한 문제점을 해결하기 위하여 확률론적 해석기법이 활용되어 왔으며 최근에는 퍼지집합이론(fuzzy set theory)을 이용한 해석기법이 활용되고 있다. 특히 확률변수들의 자료 양이 제한적인 경우 변수의 확률특성을 정확하게 파악하기 힘들어 확률론적 해석기법의 활용이 제한적일 수 있으며 이러한 경우 퍼지집합이론은 확률변수의 특성을 효과적으로 표현할 수 있다. 본 연구에서는 암반사면의 안정성 해석과정에서 포함되는 불확실성을 정량화하기 위해 퍼지신뢰도척도(fuzzy reliability measure)를 활용하여 분석을 수행하였으며 특히 암반사면의 안정성에 영향을 미치는 여러 지질공학적 특성중 불연속면의 경사와 내부마찰각을 삼각형 퍼지숫자(fuzzy number)로 해석하였다 이를 위하여 연구대상사면을 선정하여 암반사면에서 발생하는 평면파괴를 대상으로 분석을 수행하였다. 퍼지신뢰도(fuzzy reliability) 해석에서는 퍼지숫자에 대한 퍼지 연산을 통해 퍼지신뢰도 지수(fuzzy reliability index)를 획득하였으며 이러한 결과를 확률론적 해석 결과와 비교하기 위하여 몬테카를로모사기법(Monte Carlo simulation)과 점추정법(point estimate method)을 이용한 확률론적 해석을 수행하였다. 해석결과 불충분한 자료 등으로 인해 불확실성의 정량화가 어려운 경우 퍼지신뢰도 해석을 통해 적절한 퍼지신뢰도 지수와 파괴확률을 획득할 수 있을 것으로 판단된다.

• 문화기술의 융합
• /
• 제8권1호
• /
• pp.507-512
• /
• 2022

연구 대상은 교량 접속도로 절취비탈면으로서 파괴 위험 가능성이 큰 중생대 경상누층군 퇴적암 비탈면이다. 비탈면의 구성 암석은 사암, 미사암 및 암맥이며, 불연속면은 층리와 전단절리, 인장절리 및 암맥 접촉면이 발달한다. 구간별로 파괴의 유형과 규모는 암석의 종류와 불연속면의 배향에 따라 다양하나 평면파괴가 우세하고, 파괴암체의 크기는 대부분 1m³ 이하이다. face-mapping 자료, SMR, 암석의 물성·역학시험, 구간별 지질횡단면도 분석 및 한계평형해석으로 종합·검토한 결과, 대표적 단면 모두 건기 시와 우기 시의 허용안전율에 크게 미달하여 대책공법이 필요 하였다. 따라서 경제성, 효율성, 현장 특성, 등을 고려하여 비탈면 내 구간과 위치에 따라 대책공법 안을 제안하였고 대책공법을 적용한 후 비탈면의 건기 및 우기 시의 안전율은 모두 허용안전율을 상회 하였다. 특히, 법면 face-mapping 자료와 법면에 수직인 여러 대표 구간의 지질횡단면도, 그를 기본도면으로 사용한 한계평형해석 및 대책공법 제시는 비탈면의 객관적인 해석 및 안정성 검토의 합리적인 도구가 될 것으로 예상한다.

• International Journal of Concrete Structures and Materials
• /
• 제8권2호
• /
• pp.141-155
• /
• 2014

The use of fiber reinforced polymer (FRP) composites in strengthening reinforced concrete beam-column subassemblies has been scrutinised both experimentally and numerically in recent years. While a multitude of numerical models are available, and many match the experimental results reasonably well, there are not many studies that have looked at the efficiency of different finite elements in a comparative way in order to clearly identify the best practice when it comes to modelling FRP for strengthening. The present study aims at investigating this within the context of FRP retrofitted reinforced concrete beam-column subassemblies. Two programs are used side by side; ANSYS and VecTor2. Results of the finite element modeling using these two programs are compared with a recent experimental study. Different failure and yield criteria along with different element types are implemented and a useful technique, which can reduce the number of elements considerably, is successfully employed for modeling planar structures subjected to in-plane loading in ANSYS. Comparison of the results shows that there is good agreement between ANSYS and VecTor2 results in monotonic loading. However, unlike VecTor2 program, implicit version of ANSYS program is not able to properly model the cyclic behavior of the modeled subassemblies. The paper will be useful to those who wish to study FRP strengthening applications numerically as it provides an insight into the choice of the elements and the methods of modeling to achieve desired accuracy and numerical stability, a matter not so clearly explored in the past in any of the published literature.

• 대한핵의학회지
• /
• 제38권5호
• /
• pp.331-337
• /
• 2004

Cardiac neurotransmission imaging allows in vivo assessment of presynaptic reuptake, neurotransmitter storage and postsynaptic receptors. Among the various neurotransmitter, I-123 MIBG is most available and relatively well-established. Metaiodobenzylguanidine (MIBG) is an analogue of the false neurotransmitter guanethidine. It is taken up to adrenergic neurons by uptake-1 mechanism as same as norepinephrine. As tagged with I-123, it can be used to image sympathetic function in various organs including heart with planar or SPECT techniques. I-123 MIBG imaging has a unique advantage to evaluate myocardial neuronal activity in which the heart has no significant structural abnormality or even no functional derangement measured with other conventional examination. In patients with cardiomyopathy and heart failure, this imaging has most sensitive technique to predict prognosis and treatment response of betablocker or ACE inhibitor. In diabetic patients, it allow very early detection of autonomic neuropathy. In patients with dangerous arrhythmia such as ventricular tachycardia or fibrillation, MIBG imaging may be only an abnormal result among various exams. In patients with ischemic heart disease, sympathetic derangement may be used as the method of risk stratification. In heart transplanted patients, sympathetic reinnervation is well evaluated. Adriamycin-induced cardiotoxicity is detected earlier than ventricular dysfunction with sympathetic dysfunction. Neurodegenerative disorder such as Parkinson's disease or dementia with Lewy bodies has also cardiac sympathetic dysfunction. Noninvasive assessment of cardiac sympathetic nerve activity with I-123 MIBG imaging nay be improve understanding of the pathophysiology of cardiac disease and make a contribution to predict survival and therapy efficacy.

• 센서학회지
• /
• 제14권6호
• /
• pp.374-380
• /
• 2005

Vibration sensors have a wide scope of applications in the field of monitoring systems that needs to perceive an undesirable physical vibration before a critical failure occurs in a system, and then costly unplanned repairs can be avoided. The conventional vibration sensors developed so far have many disadvantages, such as complex manufacturing process, bulkiness, high cost, less reliability and so on. This paper reports a simple-structured vibration sensor, which has been developed using a commercialized conductive ball and silicon bulk-micromachining technology. The sensor consists of a conductive ball placed in $600{\mu}m$-deep micromachined silicon groove, in which Au thin film has been patterned using a shadow mask technique. Prior to the formation of the Au thin film, the sharp convex corner was rounded for smooth meatl deposition on the non-planar surface at the edge of the groove. The measurement results of the fabricated vibration sensor demonstrate a stable response characteristic to low-frequency vibration range ($1{\sim}30{\;}Hz$).

• Computers and Concrete
• /
• 제5권3호
• /
• pp.217-241
• /
• 2008

In this paper, a total strain-based hysteretic material model based on MCFT is proposed for non-linear finite element analysis of reinforced concrete structures. Although many concrete models have been proposed for simulating behavior of structures under cyclic loading conditions, accurate simulations remain challenging due to uncertainties in materials, pitfalls of crude assumptions of existing models, and limited understanding of failure mechanisms. The proposed model is equipped with a fully generalized hysteresis rule and is formulated for 2D plane stress non-linear finite element analysis. The proposed model has been formulated in a tangent stiffness-based finite element scheme so that it can be used for most general finite element analysis packages. Moreover, it eliminates the need to check that tensile stresses can be transmitted across a crack. The tension stiffening model is a function of the bar orientation and any orientation can be accommodated. The proposed model has been verified with a series of experimental results of 2D RC planar panels. This study also demonstrates how parameters of the proposed model associated with cyclic damage modeling influences the pinched cyclic shear behavior.

• Geomechanics and Engineering
• /
• 제23권4호
• /
• pp.301-311
• /
• 2020

In this study, shear strength behavior of fine-grained soils was investigated under unsaturated conditions. The samples in the unsaturated state were subjected to a net normal stress (σ-u_a) of 40 kPa and different matric suctions (u_a-u_w) of 50, 100 and 150 kPa. The matric suction values applied in the triaxial tests were selected according to the bubbling pressures determined from the SWC curves. The study was carried out on prepared re-constituted cylindrical samples by uniaxial consolidation of soil slurries. First, consolidated drained (CD) triaxial compression tests were performed on the saturated samples and the cohesion and angle of internal friction were determined. After that, drained triaxial compression tests under matric suctions were performed on the unsaturated samples. In order to obtain unsaturated test results, cohesion and internal friction angle values of saturated samples were used. The nonlinear surface representing the shear strength surface was approximated consisting of two planes (double planar surface). The reason for the nonlinear behavior of some soils is that the amount of sand content contained in it is relatively high and the bubbling pressure/permanent water content value is relatively low.

• Earthquakes and Structures
• /
• 제14권6호
• /
• pp.505-523
• /
• 2018

Static pushover analyses of typical existing reinforced concrete frames, designed according to the previous generations of design codes in Greece, have established these structures' inelastic characteristics, namely overstrength, global ductility capacity and available behaviour factor q, under planar response. These were compared with the corresponding demands at the collapse limit state target performance point. The building stock considered accounted for the typical variability, among different generations of constructed buildings in Greece, in the form, the seismic design code in effect and the material characteristics. These static pushover analyses are extended, in the present study, in the time history domain. Consequently, the static analysis predictions are compared with Incremental Dynamic Analysis results herein, using a large number of spectrum compatible recorded base excitations of recent destructive earthquakes in Greece and abroad, following, for comparison, similar conventional limiting failure criteria as before. It is shown that the buildings constructed in the 70s exhibit the least desirable behaviour, followed by the buildings constructed in the 60s. As the seismic codes evolved, there is a notable improvement for buildings of the 80s, when the seismic code introduced end member confinement and the requirement for a joint capacity criterion. Finally, buildings of the 90s, designed to modern codes exhibit an exceptionally good performance, as expected by the compliance of this code to currently enforced seismic provisions worldwide.

• 한국결정성장학회지
• /
• 제20권2호
• /
• pp.101-105
• /
• 2010

플라즈마 에쳐 내에 사용되는 실리콘 전극과 링 부품은 사용 중에 강한 플라즈마와 접촉하면서 주기적인 가열과 냉각 과정을 거친다. 이 때 부품의 표면에서는 열 응력으로 인하여 PSB라고 하는 띠 형상의 결함이 생성되며 이로 인하여 그 수명을 다하게 된다. 원료인 실리콘 잉곳의 관점에서 그 수명에 미치는 인자를 살펴보았다. 잉곳의 등급, 즉 S/F와 S/A에 따라 불순물과 결함의 농도를 GDMS와 ${\mu}$-PCD로 평가하여 잉곳의 어떤 요소들에 의하여 수명이 결정되는가를 분석하였다. 그 결과, {001} 면상에서 관찰되는 <110> 방향의 면 결함들이 PSB와 연결될 가능성이 있음을 제안하였다.