• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.735-741
• /
• 2003

A simplified view of array design and application process was introduced. Array design is critical to achieve a successful phased array measurements. A planar microphone array is designed to produce optimum performance and also to fit economic requirement in integrating data acquisition system. Certain performance characteristics are of primary concern when designing arrays. These characteristics include array resolution, spatial aliasing and array sidelobe suppression. Every array has its directional pattern that shows such characteristics. Assuming that a monopole source is located in center, beam-patterns have been simulated varying measurement conditions such as number of sensors. array aperture size, distance between array and source, frequency of interest and so on. Sensor correction was conducted on very channel using magnitudes and phased of FRF with respect to a reference microphone channel. Then with a spiral type array, measurements have been made with two point sources of same frequency in order to investigate array resolving abilities. It is observed that higher frequency source achieves better resolution than lower one does.

• Structural Engineering and Mechanics
• /
• v.15 no.5
• /
• pp.513-534
• /
• 2003

Using fluid dampers to connect adjacent buildings for enhancing their seismic resistant performance has been recently investigated but limited to linear elastic adjacent buildings only. This paper presents a study of inelastic seismic response of adjacent buildings linked by fluid dampers. A nonlinear finite element planar model using plastic beam element is first constructed to simulate two steel frames connected by fluid dampers. Computed linear elastic seismic responses of the two steel frames with and without fluid dampers under moderate seismic events are then compared with the experimental results obtained from shaking table tests. Finally, elastic-plastic seismic responses of the two steel frames with and without fluid dampers are extensively computed, and the fluid damper performance on controlling inelastic seismic response of the two steel frames is assessed. The effects of the fundamental frequency ratio and structural damping ratio of the two steel frames on the damper performance are also examined. The results show that not only in linear elastic stage but also in inelastic stage, the seismic resistant performance of the two steel frames of different fundamental frequencies can be significantly enhanced if they are properly linked by fluid dampers of appropriate parameters.

• Steel and Composite Structures
• /
• v.4 no.6
• /
• pp.489-507
• /
• 2004

The flexibility of the connection between steel and concrete largely influences the global behaviour of the composite beam. Therefore the way the connection is modelled is the key issue in its structural analysis. Here we present a new strain-based finite element formulation in which we consider non-linear material and contact models. The computational efficiency and accuracy of the formulation is proved with the comparison of our numerical results with the experimental results of Abdel Aziz (1986) obtained in a full-scale laboratory test. The shear connectors are assumed to follow a non-linear load-slip relationship proposed by Ollgaard et al. (1971). We introduce the notion of the generalized slip, which offers a better physical interpretation of the behaviour of the contact and gives an additional material slip parameter. An excellent agreement of experimental and numerical results is obtained, using only a few finite elements. This demonstrates that the present numerical approach is appropriate for the evaluation of behaviour of planar composite beams and perfect for practical calculations.

• Steel and Composite Structures
• /
• v.24 no.4
• /
• pp.425-439
• /
• 2017

As a thin-walled structure, local joint flexibility (LJF) in a tubular structure is prominent, and it may produce significant effect on the static performance for the overall structure. This study presents a simplified analytical model to analyze the static behavior for a steel tubular structure with LJF. The presented model simplifies a tubular structure into a frame model consisted of beam elements with considering the LJFs at the connections between any two elements. Theoretical equations of the simplified analytical model are deduced. Through comparison with 3-D finite element results of two typical planar tubular structures consisted of T- and Y-joints respectively, the presented method is proved to be accurate. Furthermore, the effect of LJF on the overall performance of the two tubular structures (including the deflection and the internal forces) is also investigated, and it is found from analyses of internal forces and deformation that a rigid connection assumption in a frame model by using beam elements in finite element analysis can provide unsafe and inaccurate estimation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.6
• /
• pp.132-141
• /
• 1998

Particle image velocimetry(PIV), a planar measuring technique, is an efficient tool for studying the complicated flow field such as in-cylinder flow, and intake port flow. PIV can be also used for analyzing the integral length scale of turbulence, which is a measure of the size of the large eddies that contain most of the turbulence kinetic energy. In this study, dual color scanning PIV was designed and demonstrated by using a rotating mirror and a beam splitter. This PIV system allowed enlargement of flexibility in the intensity of vectors to be calculated by spatial filtering technique, even in combustion chamber with high velocity gradient and high vorticity$({\sim}1000s^{-1})$. A new color image processing algorithm was developed, which was used to find the direction of particle movement directly from the digital image. These measuring techniques were successfully applied to obtaining the turbulence intensity (~0.1m/s) and the turbulent integral length scale of vorticity(~1mm).

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.3
• /
• pp.220-224
• /
• 2017

In this paper, a method of feeding for the near field beam scanning array antenna with three dimensional focal point has been studied. The conventional array antenna theory is mostly about the far field points. The basic idea is to feed the transmitted signal so that it is in phase at the desired point. In this study, a method is proposed to compensate the phase to have the maximum received power at the point where the measurement point distance is near to the array antenna size. In the proposed method, 11 point source antennas are arrayed in three ways in free space. And the contour map is plotted by calculating the radiation patterns in the three dimensional space and the received signal intensities in the plane within the near space. As a result, it was confirmed that 3 dimensional beam scanning is possible also in the near field of the array antenna.

• The korean journal of orthodontics
• /
• v.46 no.6
• /
• pp.345-355
• /
• 2016

Objective: The purpose of this study was to determine whether predicting maturation of the midpalatal suture is possible by classifying its morphology on cone-beam computed tomography (CBCT) images and to investigate relationships with other developmental age indices. Methods: The morphology of the midpalatal suture was assessed by using CBCT images of 99 patients. Axial plane images of the midpalatal suture were classified into five stages according to the classification scheme. To make the assessment more accurate, the morphology and fusion of the midpalatal suture were additionally investigated on coronal cross-sectional planar images and volume-rendered images. Bone age was evaluated using the hand and wrist method (HWM) and cervical vertebrae method (CVM); dental age (Hellman's index), sex, and chronological age were also assessed. To evaluate relationships among variables, Spearman's rho rank test was performed along with crosstabs using contingency coefficients. Results: The HWM and CVM showed strong correlations with the maturation stage of the midpalatal suture, while other indices showed relatively weak correlations (p < 0.01). Through crosstabs, the HWM and CVM showed high association values with CBCT stage; the HWM demonstrated slightly higher values (p < 0.0001). Based on the HWM, the midpalatal suture was not fused until stage 6 in both sexes. Conclusions: Among developmental age indices, the HWM and CVM showed strong correlations and high associations, suggesting that they can be useful in assessing maturation of the midpalatal suture.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.2
• /
• pp.69-77
• /
• 2009

Small size and low profile antenna for mobile vehicular-top-mounted is needed in satellite communication services such as DBS, Satellite Internet and VSAT. In middle latitudes, the development of an array antenna which has the conformal, low profile and 45 degree beam tilted configuration, and has the high gain with sharp beamwidth, low sidelobe and low loss is required for Ka band satellite communication. In this paper, in order to meet with these performances, an array antenna consisting of the vertical polarized waveguide longitudinal slots based on the leaky-wave mode of traveling wave antenna is proposed. Especially, for the lower sidelobe level the radiation power control using a design method of the different slot width is proposed. An array antenna consisting of 32 leakywave elements is showing 34.4 dBi of gain, 3.6 degree of beamwidth, below than -25 dB of sidelobe level, 43 degree of beam tilt angle in center frequency 20.0 GHz. Feed network designed by waveguide cooperated feed shows good performance of wideband and low loss.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.8
• /
• pp.1110-1116
• /
• 2021

In this paper, we propose a conformal Ku-band data link antenna to ensure low RCS of stealth UAV. As a phased array antenna with electrical beam steering function, a transmitter and a receiver were designed and manufactured for FDD communication, respectively. Each antenna is designed as a 12*12 planar array antenna and has a function to form a uni-directional pattern and a bi-directional pattern through phase control of unit elements. The beam steering range is designed to be able to steer up to 60 degrees in theta direction and 360 degrees in the phi direction. As a result of manufacturing and measurement, the conformal type radome has low transmission loss and meets the required specifications including system performance. The feasibility of mounting the stealth UAV has been confirmed, and future research directions such as interworking of baseband devices and conversion to digital beam steering function are suggested.

• Journal of the Optical Society of Korea
• /
• v.7 no.3
• /
• pp.180-187
• /
• 2003

A theoretical presentation by using a three-dimensional finite difference beam propagating method (3-D FD-BPM) for the evanescent coupling is offered with respect to the refractive indexes between a side-polished optical fiber and an infinitely planar waveguide with a conductor cladding (PWGCC). The PWG is suspended at a constant distance from an unclad fiber core and attached with a perfect conductor (PEC) on one side. The coupling and propagation of light are found to depend on both the relationship between the refractive index values of two structures and the configuration of the side-polished fiber used in the PWGCC. The spreading of light in the unconfined direction of a PWGCC is presented with the distribution of electric fields in xy - plane and the absolute amplitude of electric fields along the x and y axis. The power of the light propagation in a fiber decreases exponentially along the fiber axis as it is transferred to the PWGCC, where it is carried away.