• Composites Research
• /
• v.29 no.5
• /
• pp.256-261
• /
• 2016

In this work, we have prepared the filter papers with the pitch-based activated carbon fibers and the binder fibers using wet-laid process. The influence of the binder fiber on the porosity of the filter papers has been investigated by using nitrogen adsorption isotherms at 77 K and a scanning electron microscope (SEM). As a result, the specific surface area has increased with an decrease in the content of binder fiber. It has been shown that the optimum ratio of pitch-based activated carbon fibers and the binder fibers is 70:30, resulting in high porosity, excellent bonding strength, large specific surface area ($650.4m^2/g$) and high noxious gas removal efficiency (86.9%). In addition, it has been observed that the mean pore size distribution of the fiber papers has not been affected by the binder fiber.

• Journal of Industrial and Engineering Chemistry
• /
• v.67
• /
• pp.276-283
• /
• 2018

For the first time, polyvinyl chloride (PVC) was used as an easily-handled chlorine source for preparation of isotropic pitch-based carbon fiber (IPCF) incorporating ethylene bottom oil (EO) as a raw material. Pitch precursors were prepared by the chlorination-dehydrochlorination triggered by chlorine radicals originated from PVC; aromatization and poly-condensation reactions occurred by polyene-type radicals from PVC. Radical production and co-carbonization were facilitated by pretreatments of EO through vacuum distillation, bromination, and additional heat treatment. Pitches were prepared by the co-carbonization of pretreated EO and EO containing 20 wt% PVC, and had higher yields and better spinnability than those by simple distillation.

• Carbon letters
• /
• v.8 no.2
• /
• pp.127-133
• /
• 2007

In this study, commercially available pitch-based carbon fibers of general grade were post-heat-treated using a boxtype high temperature furnace at $1800^{\circ}C$, $2000^{\circ}$, $2200^{\circ}C$, and $2400^{\circ}C$, respectively. The fundamental characteristics of each heat-treated carbon fibers were investigated in terms of chemical composition, morphology, thermal stability, X-ray diffraction, single filament tensile test, and electrical resistivity. The result showed that the fiber properties were significantly influenced by the post-heat-treatment, indicating the greater effect with increasing treatment temperature. The carbon contents, thermal stability, and tensile properties of the carbon fibers used here were further increased by the post-heat-treatment, whereas the d-spacing between graphene layers and the electrical resistivity were reduced with increasing post-heat-treatment temperature.

• Composites Research
• /
• v.31 no.6
• /
• pp.412-420
• /
• 2018

In this work, phenolic resins containing conductive carbon fillers, such as, petroleum coke, carbon black, and graphite, were used to improve the surface heating elements by impregnating a pitch-based carbon paper. The influence of conductive carbon fillers on physicochemical properties of the carbon paper was investigated through electrical resistance measurement and thermal analysis. As a result, the surface resistance and interfacial contact resistivity of the carbon paper were decreased linearly by impregnating the carbon fillers with phenol resins. The increase of carbon filler contents led to the improvement of electrical and thermal conductivity of the carbon paper. Also, the heating characteristics of the surface heating element were examined through the applied voltage of 1~5 V. With the applied voltage, it was confirmed that the surface heating element exhibited a maximum heating characteristic of about $125.01^{\circ}C$(5 V). These results were attributed to the formation of electrical networks by filled micropore between the carbon fibers, which led to the improvement of electrical and thermal properties of the carbon paper.

• Proceedings of the Korean Fiber Society Conference
• /
• 1997.04a
• /
• pp.323-327
• /
• 1997

• Carbon letters
• /
• v.16 no.2
• /
• pp.121-126
• /
• 2015

Carbon fibers are prepared by stabilizing pitch fibers accompanying electron beam (E-beam) irradiation. The carbon fibers pretreated by E-beam irradiation achieve a higher stabilization index than the carbon fibers that are only heat-stabilized. In addition, the carbon fibers subjected to E-beam irradiation in the stabilization step exhibit a comparable tensile strength to that of general purpose carbon fibers. The carbon fibers pretreated with an absorbed dose of 3000 kGy have a tensile strength of 0.54 GPa for a similar fiber diameter. Elemental, Fourier-transform infrared spectroscopy, and thermogravimetric analyses indicate that E-beam irradiation is an efficient oxidation and dehydrogenation treatment for pitch fibers by showing that the intensity of the aliphatic C-H stretching and aromatic $CH_2$ bending (out-of-plane) bands significantly decrease and carbonyl and carboxylic groups form.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1991.10a
• /
• pp.99-106
• /
• 1991

Result of an experimental study on the manufacture, the mechanical properties and waterightness of pitch-based carbon fiber reinforced fly ash.cement composites are presented in this paper. The carbon fiber reinforced fly ash.cement composites using early strength cement, silica powder and a small amount of stylene butadiene rubber latex are prepared with carbon fiber, foaming agents and mixing conditions. As a result, the mechanical and plysical properties such as compresive, tensile and flectural strengths, watertightness and cement composites are improved by using a small amount of stylene butadiene rubber latex.

• Carbon letters
• /
• v.9 no.2
• /
• pp.121-126
• /
• 2008

High modulus pitch based carbon fibers (HM) were exposed to isothermal oxidation using tube furnace in carbon dioxide gas to study the oxidation kinetics under the temperature of $800-1100^{\circ}C$. The kinetic equation $f=1-{\exp}(-at^b)$ was introduced and the constant b was obtained in the range of 1.02~1.42. The oxidation kinetics were evaluated by the reaction-controlling regime (RCR) depending upon the apparent activation energies with the conversion increasing from 0.2 to 0.8. The activation energies decrease from 24.7 to 21.0 kcal/mole with the conversion increasing from 0.2 to 0.8, respectively. According to the RCR, the reaction was limited by more diffusion controlling regime for the HM fibers with the conversion increasing. Therefore, it seems that the oxidation which is under the diffusion controlling regime takes place continuously from the skin to the core of the fiber.

• Carbon letters
• /
• v.5 no.1
• /
• pp.27-33
• /
• 2004

Structural changes of high modulus carbon fiber by oxidation in carbon dioxide gas using SEM, TEM, and XRD have been observed. It was shown that the originally high modulus carbon fiber is composed of highly ordered graphitic crystalline area and non-crystalline area. It was observed that the La increases during the whole oxidation process. It was shown that the oxidation of high modulus carbon fiber initiates at the non-crystalline area and at the ends of fiber. The large pores developed in fiber by direction of fiber length at high temperature ($1,100^{\circ}C$), and the small pores developed on the fiber surface at low temperature ($900^{\circ}C$). In conclusion, it is found that the oxidation of the carbon fiber was progressed through the imperfection.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1989.10a
• /
• pp.31-34
• /
• 1989

In order to discuss the engineering properties of carbon fiber reinforced cement composites with silica fume and silica powder, experimental studies in the CFRC were carried out. The types of fiber used which are in CFRC are PAN-based carbon fiber and Pitch-based carbon fiber. To examine the effects of types, lengths, contents of carbon fiber and matrices, their properties of fresh and fardened CFRC were tested. According to the test results, the process technology of light-weight CFRC is developed and their potimum mix proportions are successfully proposed. Also, it can be concluded that the reinforcement of carbon fiber is considerably effective in improving tensile strenghth, flexural strength, toughness and loss of shrinkage of CFRC compared with conventional mortar.