• Journal of the Korean Geotechnical Society
• /
• v.15 no.6
• /
• pp.239-249
• /
• 1999

In this study, experimental work has been carried out to investigate the effect of lateral soil movement on passive piles. This paper consists mainly of two parts: the first, performance of a series of laboratory experiments on a single pile and one-row pile groups, and the second, comparison between the measured and the predicted results. In the laboratory experiments, a quadrilateral soil movement profile was imposed on model piles embedded in both sandy soils and weathered soils. The maximum bending moment and pile deflection induced in passive piles were found to be highly dependent on pile stiffness, pile spacing, relative densities and pile head fixity condition. It was shown that the group effect might either increase or decrease the maximum bending moment and pile deflection, depending on the aforementioned influence factors. Based on the results obtained, a spacing-to-diameter ratio of 7.0 seems to be large enough to eliminate the group effect, and a pile in such a case behaves essentially the same as a single pile.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.6
• /
• pp.5-14
• /
• 2001

This paper describes a simplified design method of stabilizing piles based on an experimental tests and an analytical study which can take into account the safety factor of slope and pile spacing. The nonlinear characteristics of the soil-pile interaction for stabilizing piles are modeled by using load transfer method. The interaction factors due to pile spacing and cap rigidity were estimated by using a three dimensional nonlinear finite element approach and laboratory tests. Based on the results obtained, the interaction factors are proposed quantitatively for one-row pile groups with spacing-to-diameter ratios varying far 2.5 to 7.0. The Bishop's simplified method of slope stability analysis is extended to incorporate the soil-pile interaction and determine the safety factor of the reinforced slope. Through the comparative study, it is found that the prediction by present approach is in relatively good agreement with the results of centrifuge tests and field tests and three dimensional finite element analyses.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.4
• /
• pp.567-578
• /
• 2018

In this study, to investigate the effect of the stress reduction of group piles by dynamic loading, a dynamic p-y curve was established and the dynamic p-multiplier was calculated. Dynamic numerical analysis was performed by input sinusoidal waves to the bottom of the pile - ground system for $2{\times}2$ group pile, single pile and $5{\times}5$ group pile, single pile in dry sandy soil, and the pile spacing was changed to 2.5 and 5.0 times of the pile diameter. By establishing and comparing the dynamic p-y curves of the single pile and group piles, the dynamic group pile effect of the piles according to the pile center spacing and row position of the group pile piles is analyzed. $5{\times}5$ showed symmetry of the dynamic P-multiplier value around the pile origin coordinate. The dynamic p-multiplier value at the single pile, $5{\times}5$ pile (pile spacing: 2.5D) is 0.26 ~ 0.30 at the pile number 3, pile number 23, 0.14 pile number 13, and 0.14 ~ 0.38 at the pile number 5, pile number 18. These values differed from the static p-multiplier, especially due to the different loading conditions. The dynamic p-multiplier ($P_{dm}$) estimation through various types of input dynamic loads is expected to be used for dynamic design and analysis of group pile-ground systems of civil foundation structures.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.1
• /
• pp.5-18
• /
• 2016

In this study, we grasped the resistance state of the back ground which had a notable influence on computing the lateral resistance of the laterally loaded pile group in the homogeneous ground by the model test. Resistance state was grasped as the depth of rotation-point, wedge failure angle, and wedge wing angle. The model experiment is performed by varying the width, spacing and number of piles and the relative density of sand in this study. According to the observation of the rear ground surface deformation of the piles in lateral load, rotation point ratio, wedge failure angle, and wedge wing angle of the front row were similar to those of the middle row; however, those of the back row were relatively smaller. The rotation point ratio, wedge failure angle and wedge wing angle of the piles in parallel were the same as those of a single pile. Based on the model test results, equations for estimation of the rotation-point, wedge failure angle, and wedge wing angle are proposed.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.3
• /
• pp.157-162
• /
• 2000

측발유동을 받는 일렬 군말뚝의 그룹효과를 파악하이 위해 3차원 유한요소해석을 수행하였다. 국내의 대표적인 화강풍화토 지반에 선단지지된 말뚝을 대상으로 측방으로 지반변위 발생시 말뚝 두부조건과 중심간격(2.5D, 5.0D, 7.0D, 단독말뚝) 및 말뚝주면의 접촉효과를 고려한 군말뚝의 상호작용계수를 산정하였다. 본 연구 결과, 단독말뚝과 비교하여 군말뚝의 간격이 좁아짐에 따라 상호작용계수는 현저하게 감소하였으며 말뚝 두부조건이 회전구속, 힌지,자유단의 순으로 감소정도가 크게 나타났다. 이는 실내모형실험을 통해 산정된 상호작용계수와도 비교적 잘 일치함을 보였다.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.7
• /
• pp.47-57
• /
• 2011

The p-y curve has been used to design pile foundations subjected to lateral loading. Although the p-y curve has a large influence on the pile lateral behavior, p-y curves have not been clearly suggested. In this study, the p-y curve of clay was evaluated for drilled shafts in marine deposits by using 3-dimensional numerical analyses. First, the optimization study was performed to properly determine boundary extent, mesh size, and interface stiffness. The numerical modeling in the study was verified by comparing the calculated and the pile loading test results. Then, the p-y curves of single and group piles were evaluated from the parametric study. The selected parameters were pile diameter, pile Young's modulus and pile head fixed condition for a single pile, and pile spacing for group piles. Finally, the p-multiplier was evaluated by comparing the p-y curves of a single pile and group piles. As a result, the p-multiplier at pile spacing of 3D was 0.83, 0.67 and 0.78 for the front, middle, and back row piles, respectively, and showed values similar to those of O'Neill and Reese (1999). For the pile group with pile spacing larger than 60, the group effect can be ignorable.