• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.337-340
• /
• 2011

In this study, qualitative and quantitative evaluations are performed using the hydraulic analysis of fiber stone for bridge pier scour protection. We can consider that the effective scour protection should be suggested from the side of hydraulic stability, structure stability, and permissible tractive force. The perfect verification, however, on the fiber stone for bridge pier scour protection is not sufficient because of short literatures and experiments on the field study. The continuous research, therefore, will be needed to establish reliable verification using literatures investigation and the various experiments on the fiber stone for bridge pier scour protection.

• Composites Research
• /
• v.19 no.3
• /
• pp.43-49
• /
• 2006

In this paper, a long gauge Fiber Bragg Grating (FBG) sensor system is described and long gauge FBGs are well-suited for measuring the upper parts of the bridge piers under the extremely severe movement conditions. In the experiments, we used more than 30m long FBG sensors to measure the movement of top part of the bridge piers which are separated from the main bridge by cutting the decks. With the actuator, the deck and girders were pushed and released. We checked the movement of the top of the pier while releasing the pressure of the actuator with the long gauge fiber sensor. In order to measure the movement of the upper part of the pier, the reference point must be outside of the pier. Using the optical fiber sensors, one end of the sensor is attached to the top of the pier and the other end is attached to the bottom of the next pier. The fiber sensors showed good response to the release loading and we could calculate the movement of the top part of the pear.

• Earthquakes and Structures
• /
• v.25 no.2
• /
• pp.89-97
• /
• 2023

In order to obtain the impact of socket connection interface forms and socket gap sizes on the seismic performance of reinforced concrete (RC) socket prefabricated bridge piers, quasi-static tests for three socket prefabricated piers with different column-foundation connection interface forms and reserved socket gap sizes, as well as to the corresponding cast-in-situ reinforced concrete piers, were carried out. The influence of socket connection structure on various seismic performance indexes of socket prefabricated piers was studied by comparing and analyzing the hysteresis curve and skeleton curve obtained through the experiment. Results showed that the ultimate failure mode of the socket prefabricated pier with circumferential corrugated treatment at the connection interface was the closest to that of the monolithic pier, the maximum bearing capacity was slightly less than that of the cast-in-situ pier but larger than that of the socket pier with roughened connection interface, and the displacement ductility and accumulated energy consumption capacity were smaller than those of socket piers with roughened connection interface. The connection interface treatment form had less influence on the residual deformation of socket prefabricated bridge piers. With the increase in the reserved socket gap size between the precast pier column and the precast foundation, the bearing capacity of the prefabricated socket bridge pier component, as well as the ductility and residual displacement of the component, would be reduced and had unfavorable effect on the energy dissipation property of the bridge pier component.

• Steel and Composite Structures
• /
• v.21 no.3
• /
• pp.661-677
• /
• 2016

The quasi static test of the steel reinforced concrete (SRC) bridge piers and rigid frame arch bridge structure with SRC piers was conducted in the laboratory, and the seismic performance of SRC piers was compared with that of reinforced concrete (RC) bridge piers. In the test, the failure process, the failure mechanism, hysteretic curves, skeleton curves, ductility coefficient, stiffness degradation curves and the energy dissipation curves were analyzed. According to the $M-{\Phi}$ relationship of fiber section, the three-wire type theoretical skeleton curve of the lateral force and the pier top displacement was proposed, and the theoretical skeleton curves are well consistent with the experimental curves. Based on the theoretical model, the effects of the concrete strength, axial compression ratio, slenderness ratio, reinforcement ratio, and the stiffness ratio of arch to pier on the skeleton curve were analyzed.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.43 no.4
• /
• pp.15-26
• /
• 2015

The Daegu Metropolitan Transit Corporation Advisory Committee has chosen 5 styles of bridge-pier designs, including coating, graphic, planting, billboard and safety-facility style, based on the results of landscape simulations from a previous study. This study was conducted to investigate citizen's preferences and emotional images for each style of bridge-pier design, by aiming at the pilot urban landscape improvement section from Daebong Bridge in Suseong Gu to the crossroads near Dongseong Elementary School in Daegu Metropolitan City. The questionnaire was drawn up regarding the urban landscape improvement plans applied to the research area, and the questions were about citizens' perception of bridge-pier structures generated by constructing a light rail transit, important factors to consider when designing bridge piers, preferences for each style of bridge-pier design and emotional impact. 60.4% of the survey participants were found to perceive bridge-pier structures as unattractive, so it was necessary to improve them aesthetically. Regarding visual factors of bridge-pier designs, color was most important at 5.81, followed by form at 5.57. Regarding aesthetic component factors, harmony was most important at 6.07, followed by amenity at 6.00. In the survey participants' preference for each bridge-pier design, the graphic style was preferred most at 4.14, followed by the planting style. In emotional adjectives used for each bridge-pier design, the coating style, the safety-facility style and the non-treatment style showed similar results, and all of these styles were evaluated as artificial, lifeless and desolate. The graphic style and the billboard style showed different tendencies, depending on visual factors and aesthetic component factors applied to the graphic design used for these two bridge-pier styles. Since natural materials were used for the planting style, however, it showed high preference for such emotional images as natural and lively. The emotional adjective 'amiable' was found to affect citizens' preferences for each bridge-pier aesthetic improvement plan most, and it was also analyzed to have an effect on all the styles of bridge-pier designs. To improve the landscape of a light rail transit being constructed inside the urban area, this study quantitatively extracted citizens' preferences and emotional adjective for every style of bridge-pier design applied to the pilot urban landscape improvement section, and it is expected that the results of this study will be used as basic data to improve the landscape of bridge piers.

• Smart Structures and Systems
• /
• v.20 no.2
• /
• pp.231-246
• /
• 2017

A recent work by the authors has demonstrated the feasibility of scour evaluation for Kao-Ping-Hsi Cable-Stayed Bridge simply based on ambient vibration measurements. To further attain the goal of scour monitoring, a key challenge comes from the interference of several environmental factors that may also significantly alter the pier frequencies without the change of scour depth. Consequently, this study attempts to investigate the variation in certain modal frequencies of this bridge induced by several environmental factors. Four sets of pier vibration measurements were taken either during the season of plum rains, under regular summer days without rain, or in a period of typhoon. These signals are analyzed with the stochastic subspace identification and empirical mode decomposition techniques. The variations of the identified modal frequencies are then compared with those of the corresponding traffic load, air temperature, and water level. Comparison of the analyzed results elucidates that both the traffic load and the environmental temperature are negatively correlated with the bridge frequencies. However, the traffic load is clearly a more dominant factor to alternate the identified bridge deck frequency than the environmental temperature. The pier modes are also influenced by the passing traffic on the bridge deck, even though with a weaker correlation. In addition, the variation of air temperature follows a similar tendency as that of the passing traffic, but its effect on changing the bridge frequencies is obviously not as significant. As for the effect from the alternation of water level, it is observed that the frequency baselines of the pier modes may positively correlate with the water level during the seasons of plum rains and typhoon.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.598-602
• /
• 2006

Local scour is associate with particular local types of vortex around bridge piers. This paper is method of protection local scour for the existing Busan City subway 3 Line bridge piers and Gupo large bridge piers. In order to take design of protection of local scour this bridge piers, We calculate the local scour hole of depth , scour width, riprap construction , filter construction by formulas. We had experimental hydraulic model test for this bridge piers in order to take proof for the calculation of local scour. We knew that the vortex intensifies the local flow velocities and acts to erode sediment from the scour hole and transport it downstream. As the result of hydraulic model test, we could suggest three types method of protection local scour this bridges. We knew that FHWA HEC-18(Richardson et al. 2001: Modified CSU) Formula is useful to checking calculation as application of field. One is pier protection using the sheet piles and riprap, the others are pier protection using the riprap with filter and to make renew Wall-caisson. The best method of protection for the existing Busan City subway 3 Line bridge piers and Gupo large bridge piers is pier protection using the sheet piles and riprap.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1220-1226
• /
• 2011

The purpose of this study is to assess the seismic performance of a reinforced concrete pier using ductility demand-based seismic design method and nonlinear earthquake analysis. A computer program named MIDAS/Civil(MIDAS IT,2009) for the analysis of the reinforced concrete pier was used. The bridge pier was designed by the ductility demand-based seismic design. In addition, a seismic performance was evaluated through both capacity spectrum method and nonlinear time history method. In order to determine the seismic performance of the bridge pier, the maximum response values from the capacity spectrum method and nonlinear time history analysis were compared each other.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.19 no.3
• /
• pp.121-132
• /
• 2015

The purpose of this study is to investigate the behavior characteristics of new hollow reinforced concrete (RC) bridge pier sections with triangular reinforcement details and to provide the details and reference data. Among the numerous parameters, this study concentrates on the shape of the section, the reinforcement details and the spacing of the transverse reinforcement. Additional eight column section specimens were tested under quasi-static monotonic loading. In this study, the computer program, named RCAHEST (Reinforced Concrete Analysis in Higher Evaluation System Technology), was used. A innovative confining effect model was adopted for new hollow bridge pier sections. This study documents the testing of new hollow RC bridge pier sections with triangular reinforcement details and presents conclusions based on the experimental and analytical findings.

• Journal of KIBIM
• /
• v.3 no.4
• /
• pp.11-18
• /
• 2013

Modular technology has become a major issue of the construction industries to enhance their productivity. Modular bridge construction generally requires the collaboration between the contractor, designer, fabricator and constructor. Therefore, a readily accessible information model based on BIM technology should be provided for their communication during a construction project life-cycle. In this study, BIM based 3D information modeling was carried out for the modular bridge pier. First, the product breakdown structure (PBS) and level of detail (LOD) of the pier were defined. Based on them, 3D models were created by using parametric modeling method. In addition, database was constructed for the exchange of geometry and property data of 3D models. Finally, application areas of 3D information model were suggested, including the quantity estimation and the 4D simulation.