• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.1
• /
• pp.113-119
• /
• 2006

It is now established that more than two types of blended aggregate have beneficial effects on quality and supply of concrete in the long run. However, studies on blended aggregate have not widely been progressive and the evaluation method of its most favorable mixture proportion is still needed. Therefore this study investigated the most favorable mixture proportion through the physical experiment of fresh and hardened state's cement mortar, in response to three types of composite ratio, natural fine aggregate(Ns), crushed fine aggregate(Cs) and recycled fine aggregate(Rs). Test showed that increase of blending ratio of Ns and Cs improved fluidity of mot1ar. For the properties of compressive and flexural strength, mortar blending Ns and Cs properly, exhibited similar value to one using only Cs, while mortar mixing Rs showed lower strength value as less as 6% of control one. Mortar using only Rs exhibited the largest drying shrinkage value. In addition, even thought it is not a clear quantitative analysis, technical-imaging-skill presenting the most favorable mixture proportion 3-dimensionally is proposed in this research, in order to notify the proportion easily.

• Korean Chemical Engineering Research
• /
• v.51 no.3
• /
• pp.388-393
• /
• 2013

The study was focused to evaluate the possibility for combination membrane of bacterial cellulose (BC) and graphene with high electrical properties. BC with natural polymer matrix was known to have strong physical strength. For the combination of graphene with BC, the surface of graphene was modified with oxygen plasma by changing strength and time of radio waves in room temperature. Water contact angle of modified graphene grew smaller from $130^{\circ}$ to $12^{\circ}$. XPS analysis showed that oxygen content after treatment increased from 2.99 to 10.98%. Damage degree of graphene was examined from $I_D/I_G$ ratio of Raman analysis. $I_D/I_G$ ratio of non-treated graphene (NTG) was 0.11, and 0.36 to 0.43 in plasma treated graphene (PTG), increasing structural defects of PTG. XRD analysis of PTG membrane with BC was $2{\theta}$ same to BC only, indicating chemically combined membrane. In FT-IR analysis, 1,000 to 1,300 $cm^{-1}$ (C=O) peak indicating oxygen radicals in PTG membrane had formed was larger than NTG membrane. The results suggest that BC as an alternation of plastic material for graphene combination has a possibility in some degree on the part like transparent conductive films.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.3
• /
• pp.277-282
• /
• 2015

This study is conducted to utilize waste concrete powder (WCP) made as a by-product manufacturing high quality recycled aggregate. The blaine fineness of the used waste concrete powder was $928cm^2/g$. As the main characteristic of waste concrete powder, it showed an angular type similar to cement, but hydrated products were attached on the surface of particles. In addition, the size of the particles of waste concrete powder was larger than OPC and in terms of chemical components it had higher $SiO_2$ contents. For using WCP in soil cement-based pavement, the qualities, physical and chemical properties, of WCP should be researched. In the first step, the specified compressive strength of mortar for two types of clay sand soil and clay soil respectively was experimented to be 15 MPa and then optimum mixing ratio of chemical solidification agent were decided in the range of 1.5 - 3.0% in the replacement with cement weight content. In the second step, based on the prior experimental results, recycling possibility of WCP in soil cement-based pavement was studied. In the result of experiment the mixing ratio of WCP were 5, 10, 15 and 20% in the replacement with soil weight and the compressive strength of mortar was somewhat decreased according to the increase of the mixing ratio of WCP.

• The Journal of Engineering Geology
• /
• v.17 no.3
• /
• pp.471-481
• /
• 2007

The Landslide in natural slope is occurred mostly by a heavy rain of the summer. This landslide is influenced in soil property of the surface than the rock mass. Soils in natural slope are created by weathering phenomena of the bedrock. These soils differed to the geological conditions such as sedimentary rock, metamorphic rock and volcanic rock. Therefore, estimation of landslide in natural slope is the most important analysis of the bedrock distributions and soil characteristics. This study analyzed the soil property to the natural slopes of Busan area where is distributed to volcanic rock, granite and sedimentary rock. Soil sample conducted various soil tests for estimate the soil physical property and soil engineering characteristics, and analysis of the correlation of geological conditions. In the experiment result, soils were mainly classified by a clayey sand. It is also established that $1.07{\sim}1.99kg/cm^3$ for wet density, $28.2{\sim}39.6^{\circ}$ for angle of shearing resistance, and $8.10{\times}10^{-5}{\sim}8.38{\times}10^{-2}cm/sec$ for coefficient of permeability. From the physical parameter, the soils are estimated to the permeable ground with good shear strength, and soil properties are showed a differential tendency for each geological condition.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.688-694
• /
• 2018

The mixture ratio of two-component liquid silicone is important for the inherent physical characteristics of the finished product. Therefore, it is necessary to uniformly control the ratio of the main material and the sub-material. In this paper, a mixing-ratio control system was designed, which consists of a digital flow meter and a flow control system to measure the flow rate of the raw materials and a pumping system to maintain constant pressure and transfer of the raw materials. In addition, a program was developed to control the organic interlocking and mixing ratio. For the verification of the developed system, we compared the actual weight of raw material with the value measured by the flow meter during pumping, and we measured the physical properties of the mixed material by making test samples with and without the application of the mixing-ratio improvement algorithm. The measured value was close to the reference value with a hardness range of 46-47 and tensile strength of 9.3-9.5 MPa. These results show that the mixing ratio of the liquid silicone is controlled within an error range of ${\pm}0.5%$.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.19 no.3
• /
• pp.125-131
• /
• 2013

In order to protect agricultural products against damage by physical load, various shock absorbing materials is used. As the demands of environment protection increase, the use of plastic materials have been restricted. On the other hand, Pulp mold products have some benefits - easy manufacturing, superior shock absorbing and eco-friendly. In order to develop pulp mold tray for melon packaging as shock absorbing packaging material, we investigated physical properties and vibration transmission characters of 180, 200 and 220 g pulp mold tray for melon. As the weight of pulp increased, compression strength and shock absorbing performance increased, while vibration transmissibility decreased. Especially in case of 180g pulp mold tray, it is not suitable for melon packaging because the transmitted vibration acceleration was higher than the forced vibration acceleration. And 200g pulp mold tray is suitable for melon packaging because the vibration transmissibility was lowest in three trays. And the vibration acceleration transmitted to the melon in edge of pulp mold tray was higher than to the melon in center of pulp mold tray. As the result of the simulated transportation test, the firmness of melon packaging using pulp mold tray was higher than that of conventional packaging. Therefore, these results suggest that pulp mold tray packaging could be suitable for melon packaging.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.5
• /
• pp.29-38
• /
• 2013

The G-class cement is commonly used in practice for geothermal well cementing in order to protect a steel casing that is designed to transport hot water/steam from deep subsurface to ground surface during operating a geothermal power plant. In order to maintain optimal performance of geothermal wells, physical properties of the cementing material should be satisfactory. In this paper, relevant factors (i.e., groutability, uniaxial compression strength, thermal conductivity and free fluid content) of the G-class cement were experimentally examined with consideration of various water-cement (w/c) ratios. Important findings through the experiments herein are as follows. (1) Groutability of the G-class cement increases by adding a small dose of retarder. (2) There would be a structural defect caused when the w/c ratio is kept higher in order to secure groutability. (3) Thermal conductivity of the G-class cement is small enough to prevent heat loss from hot steam or water to the outer ground formation during generating electricity. (4) The G-class cement does not form free water channel in cementing a geothermal well. (5) The Phenolphthalein indicator is applicable to the distinction of the G-class cement from the drilling mud.

• Food Science of Animal Resources
• /
• v.27 no.1
• /
• pp.35-41
• /
• 2007

This study was conducted to determine the effect of pH adjustment and addition of sodium chloride (NaCl) on quality characteristics of pork leg surimi. The pork leg surimi was manufactured with one of following pH 3.0 or pH 11.0 adjustment and contained 2% NaCl or not; C (Alaska pollack surimi, two times washing, 0% NaCl), T1 (pork leg surimi pH 3.0 adjustment, 0% NaCl), T2 (pork leg surimi, pH 3.0 adjustment, 2% NaCl), T3 (pork leg surimi, pH 11.0 adjustment 0% NaCl), T4 (pork leg surimi, pH 11.0 adjustment, 2% NaCl). The $L^*$ and W values was increased with increasing of pH value, but the $a^*$ and $b^*$ values lower. The W values were higher (p<0.05) as addition of NaCl, but $a^*$ and $b^*$ values were lower. In textural properties, the cohesiveness was increased with increasing of pH value, however with the exception of springiness all traits were higher (p<0.05) as addition of NaCl. The breaking force and gel strength was increased with increasing of pH value. The breaking force, gel strength and breaking force u deformation were higher as addition of NaCl, but shear force lower. In sensory evaluation, the tenderness was increased with increasing of pH value and all traits of sensory evaluation also were higher (p<0.05) as addition of NaCl. There were no differences in interaction of pH adjustment and without or with NaCl on color, textural properties, breaking force, deformation, gel strength, shear force and sensory evaluation of pork leg surimi. The color, textural and physical characteristics and sensory evaluation ot T2 and T4 were similar to treatment C. Therefore, the pH 11.0 and 2% NaCl addition on process of manufacture of pork leg surimi would be recommended.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.3
• /
• pp.249-259
• /
• 2009

The objective of this research was to find out the physical properties, such as dispersion and coagulation, of soil minerals depending on the types and concentrations of the cations in aqueous solution. Hwangto samples were obtained from 90 to 130 cm from surface at Jangdong-ri, Donggang-Myon, Naju, Chonnam Province. The clay fraction (< $2\;{\mu}m$) was separated by sedimentation method from the bulk soils. Both Hwangto and clay fractions, and the same samples after removal of amorphous and crystalline iron oxides were used in this experiment. The effect of 4 cations ($Na^+$, $K^+$, $Mg^{2+}$, $Ca^{2+}$) and their concentrations on settling speed and basal spacing of the minerals were observed to examine the physical properties of the soil and clay minerals. Hwangto mainly consisted of quartz, and the clay fractions consisted of kaolinite, illite, and vermiculite. The bulk soils contained 16.3 mg/kg of amorphous iron oxides and 436 mg/kg of crystalline iron oxides. Clay fractions were dispersed better than bulk soils due to their smaller particle size than that of the bulk samples in the aqueous solution. The bulk and clay samples were dispersed better when iron oxides were removed because of coating of minerals by the iron oxides. Clay minerals were settled faster as the charge and the concentration of cations added increased. The d-spacing of kaolinite and illite did not change when 4 types of cations were added. The d-spacing of vermiculite showed $14.04\;{\AA}$ when divalent cations were added while that of vermiculite showed $13.9\;{\AA}$ when monovalent cations were added. It may be attributed to the hydration radii of cations. This study indicated that both coating of iron oxides on minerals and types and concentrations of cations affect dispersion of minerals in solution and d-spacing of expanding clay minerals such as vermiculite.

• Composites Research
• /
• v.35 no.2
• /
• pp.115-119
• /
• 2022

The performance of carbon fiber is important for the production of these high-quality polymer composite materials such as CFRP (Carbon Fiber Reinforced Plastic). For this purpose, it is essential to use an optimized spinning process for improving the mechanical, physical, and structural properties of the precursor fiber, which greatly affects the properties of the carbon fiber, and the use of a suitable precursor polymer. In this study, the content of MAA (Methacrylic Acid), MAA injection time, and concentration of AIBN (2,2'-Azobis(2-methylpropionitrile)) were set as parameters for the polymer synthesis process, and Poly(AN-co-MAA) (poly(acrylonitrile-co-methacrylic acid)) was polymerized by solution polymerization. Poly(AN-co-MAA) with a molecular weight of 305,138 g/mol and an MAA ratio of 4.2% was dissolved in DMF (N,N-dimethylformamide) at a concentration of 16.0 wt%, and then a precursor fiber was prepared through dry-jet-wet spinning. The precursor fiber had a tensile strength of ~1.06 GPa and a tensile modulus of ~22.01 GPa, and no voids and structural defects were observed on the fiber.