• 대한치과보철학회지
• /
• 제31권4호
• /
• pp.661-678
• /
• 1993

The purpose of this study was to analyze the stress distribution at supporting bone according to the types of endosseous implants. This investigation evaluated the stress patterns in rectangular photoelastic models produced by four different types of dental implants such as $Br\ddot{a}nemark$, screw type of Steri-Oss, blade type of Steri-Oss, IMZ with IMC and resin tooth using the techniques of quasi-three dimensional photoelasticity. All prostheses were casted in the same nonprecious alloy and were cemented or screwed on their respective implants and abutments. 20 kg of vertical load was applied on the central fossa of casted crown and 16 kg of inclined had was applied on the top third of distal surface of casted crown respectively. The results were as follows : 1. Under the vertical load, screw implants of Steri-Oss and $Br\ddot{a}nemark$ showed increasing stress condition between and around the screw threads along the implant lateral surface and cylindrical implant of IMZ showed the less stress condition along the lateral surface with concentration of stress mostly near the root apex. 2. Under the vertical load, the stress of Steri-Oss blade was distributed uniformly at the alveolar bone under the broad blade. 3. Under the inclined load, the stress concentration of Steri-Oss screw and $Br\ddot{a}nemark$ was developed highly around the mesiocervical bone area on the contralateral side to force application. The stress of $Br\ddot{a}nemark$ with flexible gold glod was more concentrated in the cervical bone area than that of Steri-Oss with stiff screw. 4. Under the inclined load, the stress of Steri-Oss blade broadly was distributed around the mesioceivical bone area and the lower and mesial bone area of the blade. 5. Under the Inclined load, IMZ implant showed the gap between c개wn and fixture due ta deformation of the IMC and IMZ was lower in stress concentration developed around the mesiocervical bone area than $Br\ddot{a}nemark$ and Steri-Oss screw. 6. Under the inclined load, the stress magnitude induced in the mesiocervical bone area of implants was in order of $Br\ddot{a}nemark$, Steri-Oss strew, IMZ and Stsri-Oss blade. 7. Tilting forces as compared to axial forces exerted greater magnitude of stress in the cervical bone area of the implant. 8. In respect of stress distribution, Steri-Oss blade was superior than any other implants and in respect of the stability by horizontal lone, IMB and $Br\ddot{a}nemark$ was inferior than any other implants.

• 대한치과보철학회지
• /
• 제32권1호
• /
• pp.120-147
• /
• 1994

저자는 가공의치에서 임플란트와 치아간의 보철물 연결형태와 나사형 및 원통형 임플란트에서 그 형태의 차이가 주위 골조직의 응력분산에 어떤 영향을 미치는지 알아보기 위해 임플란트와 지대치를 고정성 및 반고정 성 가공의 치로 연결하고 수평면에 대해 수직 및 25도 측방하중을 가하여 주위 골조직의 응력분산 양상을 3차원적 광탄성 실험을 통해 비교 분석한 바 다음과 같은 결론을 얻었다. 1) 나사형 임플란트에서는 수직 및 측방력에 대해 경부에 응력집중이 나타났다. 2) 나사형 임플란트와 치아를 가공의치로 연결했을 경우에는 임플란트의 경부와 지대치의 치경부 및 근단부에 응력집중이 나타났으며, 고정성 가공의치로 연결했을 때에는 지대치의 치경부에 반고정성 가공의치로 연결했을 때에는 임플란트 경부에 더 큰 응력집중이 나타났다. 3) 원통형 임플란트와 치아를 가공의치로 연결했을 경우에는 임플란트와 지대치의 근단부에 응력집중이 나타났으며, 고정성 가공의치로 연결했을 때에는 지대치의 근단부에 반고정성 가공의치로 연결했을 때에는 임플란트와 지대치의 경부에 더 큰 응력집중이 나타났다. 4) 임플란트와 치아를 가공의치로 연결했을 경우에는 고정성 및 반고정성 가공의치 양쪽 모두에서 원통형 임플란트보다 나사형 임플란트에서 지대치 주위의 응력분산이 더 균등하게 나타났다. 5) 나사형 임플란트 주위의 응력분산은 임플란트 두 개를 고정성 가공의치로 연결했을 때, 가장 균등한 것으로 나타났으며, 그 다음이 치아와 고정성 가공의치로 연결했을 때, 그 다음이 치아와 반고정성 가공의치로 연결했을 때, 그리고 임플란트 단독으로 사용했을 때 가장 불리한 것으로 나타났다.TEX>$45.4{\pm}16.6m$, Panavia는 $41.3{\pm}22.9m$, 그리고 All-Bond는 $151{\pm}82m$로 나타났다. 4. 인산 아연 세멘트와 Panavia는 All-Bond에 대해 통계학적 유의성 있는 차이를 나타내었으며(p<0.05)인산 아연 세멘트와 Panavia-EX사이에는 유의성 있는 차이가 없었다(p>0.05). 비교시 All-Bond & composite resin cement 군이 Z.P.C. 군보다 높게 나타났으나 통계학적 유의성은 없었다(P>0.05).않거나 더 적게 쓰고도 농사를 지을 수 있는 영농법 및 농약을 좀 더 안전하게 살포할 수 있는 방법의 개발, 고온에서도 착용하기 좋고 보호 성능이 좋은 보호구의 개발이 시급히 요구되며, 농약살포시 환기요령과 보호구 착용방법에 대한 교육 등의 강화도 고려되어야 할 것으로 생각된다. 둘째, 농부증 증상 중 흔한 증상들은 농작업 자세 및 과도한 노동에 기인되었을 가능성이 있으므로 신체에 부담을 줄일 수 있는 농기구를 개발하고, 주기적인 휴식 및 운동을 권장해 볼 만하다. 세째, 고혈압 유소견율이 15% 전후로 높으므로 고혈압 관리사업의 강화가 요구된다.는 의료분쟁을 줄일 수 있는 방안이 마련되어야 하고, 의료보험수가의 조정도 필요할 것이다.보호차원에서 정부의 중립적 의지가 있어야 할 것으로 생각된다.의 비율이 감소하였으나 본태성고혈압, 당뇨병, 폐결핵, 협심증 둥의 비율이 증가하였다. 일반외과의 경우에는 치핵, 항문열상, 종기 등의 비율이 감소하였고, 위암, 대장암, 담낭암 등의 비율은 증가하였다.

• 한국세라믹학회지
• /
• 제51권5호
• /
• pp.487-491
• /
• 2014

In this study, we measured the thermally and chemically induced residual stresses on glaze using the photoelastic method. Porcelain with thermally induced residual stress showed compressive stress of 49 MPa for thermal expansion mismatch and a locally fluctuated stress field over the glaze layer due to compensation of compressive stresses around pores. In the case of chemically strengthened porcelain, the compressive stress on the glaze was 151 MPa which was around 3 times higher than the stress on thermally strengthened glaze. The trend of fracture strength of thermally and chemically strengthened porcelains was coincident with that of the residual stress of porcelains.

• Journal of Astronomy and Space Sciences
• /
• 제29권1호
• /
• pp.47-49
• /
• 2012

Massive binary stars lose mass by two mechanisms: jet-driven mass loss during periods of active mass transfer and by wind-driven mass loss. Beta Lyrae is an eclipsing, semi-detached binary whose state of active mass transfer provides a unique opportunity to study how the evolution of binary systems is affected by jet-driven mass loss. Roche lobe overflow from the primary star feeds the thick accretion disk which almost completely obscures the mass-gaining star. A hot spot predicted to be on the edge of the accretion disk may be the source of beta Lyrae's bipolar outflows. I present results from spectropolarimetric data taken with the University of Wisconsin's Half-Wave Spectropolarimeter and the Flower and Cook Observatory's photoelastic modulating polarimeter instrument which have implications for our current understanding of the system's disk geometry. Using broadband polarimetric analysis, I derive new information about the structure of the disk and the presence and location of a hot spot. These results place constraints on the geometrical distribution of material in beta Lyrae and can help quantify the amount of mass lost from massive interacting binary systems during phases of mass transfer and jet-driven mass loss.

• 대한조선학회지
• /
• 제4권1호
• /
• pp.55-58
• /
• 1967

It is investigated that in what shape the stress concentration factor of a notched strip under pure bending changes due to unsymmetrically varying notch angle. Four models made of CR-39, having parameters of r/d-0.225, h/r=4; r/d=0.225, h/r=2; r/d=0.4, h/r=4 and r/d=0.4, h/r=2 respectively as shown in Fig.1, Fig.2 and Table are tested with the use of polariscope. For each model, notch angle is unsymmetrically varied from $0^{\circ}$ to $180^{\circ}$ at intervals of $15^{\circ}$ as shown in Fig. 1 and Fig. 2. The results of this experiment are Fig. 7 and Fig. 8 and the following are deduced. As notch angle increases 1) from $0^{\circ}$ to $50^{\circ}$, the decrement of concentration factor is slight. 2) from $50^{\circ}$ to 90, the decrement of concentration factor is a little steeper. 3) from $30^{\circ}$ to $140^{\circ}$, the decrement of concentration factor is slight. 4) from $140^{\circ}$ to $180^{\circ}$, the decrement is very steep with an abrupt with an abrupt change in the neighborhood of $140^{\circ}$.

• 한국정밀공학회지
• /
• 제3권4호
• /
• pp.53-63
• /
• 1986

In this study, the stress distribution of rectangular bar under torsion, when warping of both ends is free or constrained, is investigated. Method of separation of variable and Fourier Series are used for the theoretical analysis, and 3dimensional photoelastic stress-freezing method for experimental analysis. The main results are as follows; 1) In the case of warping-constrained rectangular bar, the normal stresses are negligible because they are less then 0.5% of the shear stresses. The maximum normal stress is placed on the point of y=0.61 b when b/a=1 and it gradually moves to the corner y=b when the value of b/a is increased. 2) According to increase of the value of b/a, on the crossection, the maximum shear stress is placed on the middle point of the long side (x=${\pm}a$, y=0) when warping of both ends is free but the middle of the short side (x=0, y=${\pm} b$) when warping is constrained. The stress distribution is straight line when warping is constrained, namely, the stress distribution is proportional to the distance from the axis of centroid, but parabolic when warping is free. 3) The values of the combined stress of warping-constrained bar, if the influence of the loaded point is neglected, are generally smaller than those of warping-free.

• 대한치과보철학회지
• /
• 제29권2호
• /
• pp.103-115
• /
• 1991

This study was executed to analyze the stress distribution of tooth, supporting structure and overdenture by two-dimensional photoelastics when 6 types of coping were inserted. Types of coping were designed to be inclined plane, short dome, medium dome, shore square, medium square and o-p anchor attachment. Fortes were applied respectively as follows: 1) Vertical load of 10 kg on the incisal edge 2) $30^{\circ}$ diagonal load of 8 kg on the labial surface. The results were as follows: 1. In case of short dome and o-p anchor attachment, the stress is evenly distributed on teeth, supporting tissue structure under vertical and $30^{\circ}$ diagonal load, then short dome and o-p anchor attachment show better stress distribution and stabilization of overdenture than any other coping under labial diagonal load. 2. Inclined plane revealed greater tendency of displacement of overdenture than any other coping under labial diagonal load. 3. Long height of copings had greater concentration of stress than short height of copings. 4. In case of medium dome under labial diagonal load, there were high level of stress concentration on denture base contacted labioincisal angle of coping.

• Journal of the Korean Wood Science and Technology
• /
• 제16권4호
• /
• pp.54-60
• /
• 1988

Machinabilities means inherent properties of pinus densiflora at Chunyang district to be CNC machined easily or not, and processing abilities of the tool and machine together. This explanation signifies that machinabilities have two phases of signification, depended on considering and stress either materials or tools preferentially. This paper discuss machinabilities, the following items are usually employed as the indices of stress distribution at the cutting tool rake face. The stress distributions on the chip - tool contact surface at the early stage of the chip forming and under the stage of fringe pattern in wood cutting were analyzed the photoelastic method. The tool used in the present experiment was the special cutting tool H.S.S. one made in laboratory. And isochromatic fringe pattern and isolinic line of work piece by chip-behavior during the cutting operation were photographed with the feed camera continuously. The effects on the stress, distribution on the rake face of the epoxy tool and the strain distribution in the work piece of wood plate by chip behavior are cleared in pre cent experiment.

• 대한기계학회논문집A
• /
• 제28권11호
• /
• pp.1776-1785
• /
• 2004

In this research, the relationships between static bimaterial constant and dynamic oscillation index are studied. It was certified that static bimaterial constant has the same form equation as the dynamic oscillation index. Bimaterial constant and oscillation index are increased with the increment of Young's modulus ratio and approached to the some value. Isochromatic fringe patterns are slanted to the left side with increment of bimaterial constants and oscillation index. Though patterns of stress components in above the crack surface are similar to each other, their magnitudes are different a little. In the ahead of crack tip, there are big differences in the isochromatic fringe patterns and their magnitudes. The influence of bimaterial with Young's modulus ratio is bigger in the propagation crack than in the stationary crack.

• 대한조선학회지
• /
• 제7권2호
• /
• pp.27-40
• /
• 1970

The distribution of stress and strain in elastic stages is investigated by the experiments of two dimensional photoelastic coating and Moire fringe method. Center block type and cover plate type of fillet welds are used as specimens in the test. The results are as follows. 1) Center block type gets less uniform stress distribution than cover plate type. And its stress concentration factor, especially at root, is larger than that at toe. 2) When main plate and cover plate closely contact and it cause friction, stress concentration decreases more than that in case of slit. That is because stress can be transmitted on the contact surface. 3) When slit is made, the outside of fillet gets more stress than the inside of it. 4) While the plastic strain distribution of center block type reaches the maximum at root and differs very slightly from that under lower loading, the plastic strain distribution of cover plate type is inclined to get the maximum at the outside of fillet rather than at root. 5) When the plastic strain value of cover plate type is compared with that of center block type at toe and root, the relations between the former and the latter shows root<toe and root>toe. 6) Because stress distribution becomes changed according to loading, fracture angle cannot be estimated by the peaks of elastic stress distribution. 7) The strain distribution just before fracture can be found by Moire fringe method.