• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.230-231
• /
• 2005

본 논문은 광 활성도가 가장 좋은 아나타제(anatase) 상의 광촉매 $TiO_2$ 분말을 상온에서 aerosol deposition 법을 사용하여 박막을 제조하였다. 이런 제조 방법은 aerosol 분말을 초음속으로 분사하여 기판에 증착시키는 방법으로, 저온에서 박막 증착이 가능하여 thermal stress를 줄일 수 있고, 공정 단가를 낮출 수 있다는 장점이 있다. 박막 제조시 aerosol bath의 압력은 500 torr이고, chamber의 압력은 0.4 torr였다. 이런 압력차는 0.4mm$\times$10mm의 크기의 노즐을 통해 $TiO_2$ 나노 분말을 초음속으로 가속하여 기판에 증착시켰다. 박막 제조를 위해 사용한 기판은 수질정화에 응용하기 위해 직경 50mm인 원판 SUS 멤브레인을 사용하였다. SUS 멤브레인 위에 증착되어 있는 $TiO_2$ 박막의 입자 크기와 조성을 알아보기 위해 주사 현미경 (SEM) 및 EDX 분석을 하였고, l$\mu$m 정도의 입자 크기와 수처리 후에도 표면에 증착 되어진 anatase 상의 $TiO_2$ 박막을 확인할 수 있었다.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.2
• /
• pp.68-71
• /
• 2011

[ $Ti_{1-x}W_xO_{2-y}$ ]solid solutions with compositions of x = 0.01(TW-1), x = 0.02(TW-2), x = 0.03(TW-3) and x = 0.04(TW-4) were prepared at 1,073 K in air under atmospheric pressure. All the solutions exhibited tetragonal symmetries. Nonstoichiometric chemical formulas have been obtained from oxidation-reduction titration and the partial substitution of $W^{6+}$ ions mainly caused the formation of $Ti^{3+}$ ion, rather than oxygen excess. Resistivities of the samples were highly dependent on humidity. The increase of the W amount resulted in an increase of $Ti^{3+}$ content, decrease of resistivity values and finally degradation of photocatalytic activities.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.12
• /
• pp.3586-3590
• /
• 2013

We present here an efficient and simple method for preparation of highly active heterogeneous ZnO photocatalyst (graphene oxide-zinc oxide: GO-ZnO), specifically by deposition of ZnO nanoparticles onto thiolated GOs. The resultant GO-ZnO sample was characterized by TEM, XRD, Auger, XPS, and Raman measurements, revealing that the size-similar and quasi-spherical ZnO nanoparticles were anchored to the thiolated GO surfaces. The average particle diameter was about 2.5 nm. In the photodegradation of methylene blue (MB) under ultraviolet (UV) light, GO-ZnO exhibited remarkably enhanced photocatalytic efficiency compared with thiolated GO and pure ZnO particles. This strong photocatalytic performance of GO-ZnO can be attributed to the suppression of electron recombination and the enhancement of mass transportation. The results showed that thiolated GO is the preferable supporting material.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.6
• /
• pp.1579-1582
• /
• 2007

The purpose of this study is to compare degrading performance of organic contaminants in aqueous solution using photocatalyst and find an optimal condition for decomposing non-degradable matters. The parameters of this research is light intensity and state of photocatalytic material within reactor. The results showed that Type 3 (terms of plastic beads : $500^{\circ}C$, 3hr) has the greatest reactivity.

• Journal of Environmental Science International
• /
• v.27 no.7
• /
• pp.611-620
• /
• 2018

In this study, a metal-organic framework (MOF) material $NH_2$-MIL-101(Fe) was synthesized using the solvothermal method, and characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), UV-visible spectrophotometry, field-emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), and surface area measurements. The XRD pattern of the synthesized $NH_2$-MIL-101(Fe) was similar to the previously reported patterns of MIL-101 type materials, which indicated the successful synthesis of $NH_2$-MIL-101(Fe). The FT-IR spectrum showed the molecular structure and functional groups of the synthesized $NH_2$-MIL-101(Fe). The UV-visible absorbance spectrum indicated that the synthesized material could be activated as a photocatalyst under visible light irradiation. FE-SEM and TEM images showed the formation of hexagonal microspindle structures in the synthesized $NH_2$-MIL-101(Fe). Furthermore, the EDS spectrum indicated that the synthesized material consisted of Fe, N, O, and C elements. The synthesized $NH_2$-MIL-101(Fe) was then employed as an adsorbent and photocatalyst for the removal of Indigo carmine and Rhodamine B from aqueous solutions. The initial 30 min of adsorption for Indigo carmine and Rhodamine B without light irradiation achieved removal efficiencies of 83.6% and 70.7%, respectively. The removal efficiencies thereafter gradually increased with visible light irradiation for 180 min, and the overall removal efficiencies for Indigo carmine and Rhodamine B were 94.2% and 83.5%, respectively. These results indicate that the synthesized MOF material can be effectively applied as an adsorbent and photocatalyst for the removal of dyes.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.3
• /
• pp.316-322
• /
• 2006

The current study evaluated the technical feasibility of the application of $TiO_2$ photocatalysis for the removal of nocotine which has well known as a representative material of environmental tobacco smoke(ETS). Four different preliminary experiments were performed for the evaluation of nicotine removal using photocatalyst-coated construction materials. The photocatalytic removal of nicotine was investigated for five parameters: dry condition of coating tiles, type of coating sol, number of coatings, relative humidity(RH), and input concentrations. Prior to performing the parameter tests, adsorption of nicotine onto the current experimental system was surveyed. All the variables tested in the present study exhibited to influence the photocatalytic decomposition of Nicotine. A dry condition of high temperature and short dry period presented higher photocatalytic oxidation(PCO) efficiency compared to that of low temperature and long dry period. ST-KO3 sol showed higher decomposition efficiency than E-T Sol. The PCO efficiency increased as the number of coating increased. High humidity and low input concentrations exhibited higher PCO efficiency. Consequently, it is noted that the five parameters tested in the present study should be considered for the application of photocatalyst-coated construction materials in cleaning nicotine in ETS.

• Clean Technology
• /
• v.26 no.1
• /
• pp.7-12
• /
• 2020

Ti-SBA-15 catalysts doped with lanthanide ions (Ln/Ti-SBA-15) were successfully synthesized using conventional hydrothermal method. In addition, they were characterized by XRD, FT-IR, DRS, BET, and PL. The activity of these materials on the photocatalytic decomposition of methylene blue under ultraviolet light irradiation was also examined. Ti-SBA-15 catalysts doped with various lanthanide ions maintained their mesoporous structure. The pore size and pore volume of Ln/Ti-SBA-15 materials decreased but their surface area increased upon the doping of lanthanide ion. Ln/Ti-SBA-15 materials exhibited the type IV nitrogen isotherm with desorption hysteresis loop type H2, which was characteristic of mesoporous materials. The size of hysteresis increased in the doping of lanthanide ions on Ti-SBA-15 material. There was no absorption in the visible region (> 400 nm) regardless of the doping of lanthanide ions to TiO₂ particles, while the broad bands at 220 nm appeared at the Ln/Ti-SBA-15 samples, indicating the framework incorporation of titanium into SBA-15. 1 mol% Pr/ Ti-SBA-15 catalysts showed the highest photocatalytic activity on the decomposition of methylene blue but the Ti-SBA-15 catalysts doped with Eu, Er, and Nd ions showed lower activity compared to pure Ti-SBA-15 catalyst. The PL peaks appeared at about 410 nm at all catalysts while the excitonic PL signal was proportional to the photocatalytic activity for the decomposition of methylene blue.

• The Journal of Korean Academy of Prosthodontics
• /
• v.44 no.3
• /
• pp.284-294
• /
• 2006

Statement of problem. Proliferation of Candida albicans is primarily within the plaque on the fitting surface of the denture rather than on the inflamed mucosa. Consequently, the treatment of the denture is equally important as treatment of the tissue. Cleansing and disinfection should be efficiently carried-out as the organisms can penetrate into the voids of the acrylic resin and grow in them, from which they can continue to infect and reinfect bearing tissues. Purpose. The purpose of this study was to evaluate the applicability of photocatalytic reaction to eliminate Candida albicans from acrylic resin denture base, and to investigate the anti-fungal effect with various UVA illumination time. Materials and Methods. The specimens were cured by the conventional method following the manufacturer's instruction using thermal polymerized denture base resin (Vertex RS: Dentimex, Netherlands). $TiO_2$ photocatalyst sol(LT), which is able to be coated at normal temperature, was made from the Ti-alkoxide progenitor. The XRD patterns, TEM images and nitrogen absorption ability of the $TiO_2$ photocatalyst sol(LT) were compared with the commercial $TiO_2$ photocatalyst P-25. The experimental specimens were coated with the mixture of the $TiO_2$ photocatalyst sol(LT) and binder material (silane) using dip-coater, and uncoated resin plates were used as the control group. Crystallinity of $TiO_2$ of the specimen was tested by the XRD. Size, shape and chemical compositions were also analyzed using the FE-SEM/ EDS. The angle and methylene blue degradation efsciency were measured for evaluating the photocatalytic activity of the $TiO_2$ film. Finally, the antifungal activity of the specimen was tested. Candida albicans KCTC 7629(1 ml, initial concentration $10^5$ cells/ ml) were applied to the experiment and control group specimens and subsequently two UVA light source with 10W, 353 nm peak emission were illuminated to the specimens from 15cm above. The extracted $2{\mu}l$ of sample was plated on nutrient agar plate ($Bacto^{TM}$ Brain Heart Infusion; BD, USA) with 10 minute intervals for 120 minute, respectively. It was incubated for 24 hours at $37^{\circ}C$ and the colony forming units (CFUs) were then counted. Results. Compared the characteristics of LT photocatalyst with commercial P-25 photocatalyst, LT were shown higher activity than P-25. The LT coated experimental specimen surface had anatase crystal form, less than 20 nm of particle size and wide specific surface area. To evaluate the photocatalytic activity of specimens, methylene blue degradation reaction were used and about 5% of degradation rate were measured after 2 hours. The average contact angle was less than $20^{\circ}$ indicating that the LT photocatalyst had hydrophilicity. In the antifungal activity test for Candida albicans, 0% survival rate were measured within 30 minute after irradiation of UVA light. Conclusion. From the results reported above, it is concluded that the UVA-LT photocatalytic reaction have an antifungal effect on the denture surface Candida albicans, and so that could be applicable to the clinical use as a cleaning method.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.59-75
• /
• 2016

Reduced or black $TiO_{2-x}$ materials with oxygen-deficiency have been achieved by creating oxygen vacancies and/or defects at the surface using different methods. Fascinatingly, they exhibited an extended absorption in VIS and IR instead of only UV light with bandgap decrease from 3.2 (anatase) to ~1 eV. However, despite the dramatic enhancement of optical absorption in black $TiO_{2-x}$ materials, they have failed to show expected visible light-assisted water splitting efficiency. This was ascribed to the high concentration of the surface defects and/or oxygen vacancies, considered as an electron donor to enhance donor density and improve the charge transportation in black $TiO_2$ can also act as charge recombination centers, which eventually decrease photocatalytic activity. Therefore, a black ot reducd $TiO_2$ material with optimized properties would be highly desired for visible light photocatalysis. In this report, a new controlled magnesiothermic reduction has been developed to synthesize reduced black $TiO_{2-x}$ in the presence $H_2/Ar$ for photocatalytic $H_2$ production from methanol-water system. The material possesses an optimum band gap and band position, oxygen vacancies, and surface defects and shows significantly improved optical absorption in the visible and infrared region. The synergistic effects enable the reduced $TiO_{2-x}$ material to show an excellent hydrogen production ability along with long-term stability under the full solar wavelength range of light and visible light, respectively, in the methanol-water system in the presence of Pt as a co-catalyst. These values are superior to those of previously reported black $TiO_2$ materials. On the basis of all the results, it can be realized that the outstanding activity and stability of the reduced of $TiO_{2-x}$ NPs suggest that a balanced combination of different factors like $Ti^{3+}$, surface defects, oxygen vacancy, and recombination center is achieved along with optimized bandgap and band position during the preparation employing magnesiothermic reduction in the presence of $H_2$. The controlled magnesiothermic reduction in the presence of $H_2$ is one of the best alternative ways to produce active and stable $TiO_2-based$ photocatalyst for $H_2$ production.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.669-669
• /
• 2013

Hierarchical N doped TiO2 nanostructured catalyst with micro, meso and macro porosity have been synthesized by a facile self-formation route using ammonia and titanium isopropoxide precursor. The samples were calcined in different calcination temperature ranging from $300^{\circ}C$ to $800^{\circ}C$ at slow heating rate ($5^{\circ}C$/min) and designated as NHPT-300 to NHPT-800. $TiO_2$ nanostructured catalyst have been characterized by physico-chemical and spectroscopy methods to explore the structural, electronic and optical properties. UV-Vis diffuse reflectance spectra confirmed the red shift and band gap narrowing due to the doping of N species in TiO2 nanoporous catalyst. Hierarchical macro porosity with fibrous channel patterning was observed (confirmed from FESEM) and well preserved even after calcination at $800^{\circ}C$, indicating the thermal stability. BET results showed that micro and mesoporosity was lost after $500^{\circ}C$ calcination. The photocatalytic activity has been evaluated for methanol oxidation to formaldehyde in visible light. The enhanced photocatalytic activity is attributed to combined synergetic effect of N doping for visible light absorption, micro and mesoporosity for increase of effective surface area and light harvestation, and hierarchical macroporous fibrous structure for multiple reflection and effective charge transfer.