• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.606-611
• /
• 2002

Welding using lasers can be mass-produced in high speed. In the laser welding, performing real-time monitoring system of the welding quality is very important in enhancing the efficiency of welding. In this study, the plasma and molten metal which are generated during laser welding were measured using the UV sensor and IR sensors. The results of laser welding were classified into five categories such as optimal heat input, little low heat input, low heat input, partial joining due to gap mismatch, and nozzle deviation. Also, a system was formulated which uses the measured signals with a fuzzy pattern recognition method which is used to perform real-time evaluation of the welding quality and the defects which can occur in laser welding.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 D
• /
• pp.1528-1530
• /
• 1998

In this work, a possible new PD detection technique, based on the Michelson Interferometer, has been proposed. Laser beam transmitted by optical fiber is spliced into two-laser beam by 50/50 coupler, one is reflected on diaphragm, which is vibrated by ultrasonic sound, and then modulated. The other one is reference beam. They are collected into 50/50 coupler making interferenced beam which could be detected by photo detector.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.371-375
• /
• 2001

The tool wear that is developed by long-term machining in mold manufacturing with machining center makes a severe influence to the accuracy and the surface roughness. In this reason, tool-wear supervising system which has guaranteed high accuracy and high speed is needed to improve the measurement quality. Touching probe and touch sensor are widely used to measure the tool profile at on-machine measurement. In this paper, using the newly developed electric touch point measuring system, the Automatic Tool Compensation System is developed to correct the error of tool diameter resulted from the wear, and the operating method of this system is also provided.

• 한국공작기계학회논문집
• /
• 제10권4호
• /
• pp.48-54
• /
• 2001

The tool wear that is developed by long-term machining in mold manufacturing with machining center makes a severe influence to the accuracy and the surface roughness. in this reason, tool-wear supervising system which has guaranteed high accuracy and high speed is needed to improve the measurement quality. Touching probe and touch sensor are widely used to measure the tool profile at on-machine measurement. In this paper, using the newly developed electric touch point measuring system, the Automatic Tool Compensation System is developed to correct the error of tool diameter resulted from the wear, and the operating method of this system is also provided.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.445-449
• /
• 2001

The tool wear that is developed by long-term machining in mold manufacturing with machining center makes a severe influence to the accuracy and the surface roughness. In this reason, tool-wear supervising system which has guaranteed high accuracy and high speed is needed to improve the measurement quality. Touching probe and touch sensor are widely used to measure the tool profile at on-machine measurement. In this paper, using the newly developed electric touch point measuring system, the Automatic Tool Compensation System is developed to correct the error of tool diameter resulted from the wear, and the operating method of this system is also provided.

• 센서학회지
• /
• 제20권3호
• /
• pp.193-198
• /
• 2011

In this paper, we used optoelectronic feedback to generate the carrier frequency for the ASK modulation of a lighting LED. A solar cell was used for photo-detector in the feedback circuit, and the LED light was ASK modulated by controlling the ON/OFF state of the switch that is installed in the feedback loop. The oscillation frequency of the optoelectronic feedback loop was about 50 kHz and the data rate of the ASK modulation was 9.6 kbps. In experiments, the optoelectronic feedback circuit was used for the ASK modulation of a lighting LED in the transponder of a visible light identification system, and data exchange between the transponder and the reader was successfully carried out.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1882-1884
• /
• 1996

This paper deals with the lightning surge counter. In order to install the effective surge protective devices, it is important to find the parameters of incident surges. For the purpose of observing the occurrence frequency as a parameter of the amplitude of surge, two type surge counters were designed and fabricated. One is operated by surge currents, and the other is operated by surge voltages. The former consists of current sensor, metal oxide varister (MOV), rectifier, capacitor and electromagnetic counter. The latter consists of rectifier, voltage divider, comparator, photo coupler and counter circuit, and is useful for detecting the surge voltages.

• 대한기계학회논문집
• /
• 제18권10호
• /
• pp.2523-2532
• /
• 1994

In this paper, active noise control is performed in a duct system using the periodic pulse train which corresponds to the periodic component of noise source as a reference signal. Control algorithm applied in this study is possible to eliminate the acoustic feedback which occurs in the conventional filtered-x and filtered-u LMS algorithm by using electrical reference signal and has the fast adaptation speed with low filter orders by using synchronous sampling method is discussed via computer simulations and experiments of case studies such as frequency modulation, amplitude modulation and frequency differency between source signal and reference signal.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.879-883
• /
• 2000

A system for measuring and adjusting the oscillating frequency of a balance wheel whick determins the accuracy of mechanical timers. The balance wheel oscillates rotatively suspended by a hair spring which is welded at the other end to the pivot tube. The natural oscillatory frequency of the balance wheel is determined by the length of hairspring from the balance wheel to the point if other parameters the length in the torsional oscillation model are not changed, so the frequency of the balance wheel can be adjusted to meet a requirement by the adjustment of the hairspring length using ultrasonic welding. And the movement of wheel teeth is measured in realtime by a high speed photo fiber sensor and Auto Correlation is used to find a more accurate oscillation period from the measured signal with some variations.

• Journal of information and communication convergence engineering
• /
• 제4권2호
• /
• pp.92-96
• /
• 2006

Hardware for monitoring the water quality using water fleas is developed. Water flea is a frequently used biological sensor for monitoring the water quality. Water fleas quickly respond to the incoming toxic water by changing their activity when they are exposed. By measuring the activity of water fleas, the incoming toxic water is instantly detected. So far the measurement of activity of water fleas has been done with a system equipped with both a light source of LED and a light detector of photo transistor. Water flea itself is, however, sensitive to light resulting in incorrect response and the system has two inconvenient separate parts of the light source and the detector. This paper suggests a system using a CCD camera instead of a light source and a detector. The suggested system processes the image data from the CCD camera in real time without any delay. The developed system becomes a part of the remote water monitoring embedded system.