• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1005-1006
• /
• 2007

This paper analyzed the characteristics of the claw pole permanent magnet(PM) stepping motor by using 3D Finite element method(FEM). In this motor, magnetization is occurred along the z-axis, therefore it is necessary to apply 3D FEM for analysis of the claw pole motor. A phase difference of the two stacks's detent torque is 180 degrees. When the center of a permanent magnet is identical with the middle of a pole, small detent torque is produced in order to cancel each of detent torques. However, there are construction errors which are a discrepancy between one and the other phase section in the manufacturing process, thus the detent torque is increased. Moreover, it is confirmed that the proportion of the detent torque is considerably arisen according to the error. Analysis of the construction error is studied by changing the error $0^{\circ}$ to $3^{\circ}$.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.12
• /
• pp.1865-1874
• /
• 2013

In this paper, a design method of speed and position estimator based on unscented Kalman filter is proposed for the no sensor control of IPMSM(Interior Permanent Magnet Synchronous Motor). The proposed method is simple more than the estimator designed with rotation axis for current measurement. Also the proposed state estimator is designed including nonlinear terms of the estimator. The controller which constructed using nonlinear back-stepping control method is operated speed and current control using the estimated speed and currents information. Through simulation, the performance of the designed estimator is compared to the estimator which is designed to synchronize d-q axis.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.6
• /
• pp.881-889
• /
• 2013

In this paper, a nonlinear and adaptive back-stepping control technique is proposed for a speed control of IPMSM(Interior Permanent Magnet Synchronous Motor). The gain of back-stepping controller(including integral value of the states error) is designed for stability of the system. In order to adapting fast in variation of load torque, the controller is including load torque estimator. The simulation is completed by using PSIM software. The simulation results show that the designed back-stepping controller make the system stable in the constant torque region, and has better tracking performance than a controller without the integral gain.

• 전기의세계
• /
• v.31 no.1
• /
• pp.68-73
• /
• 1982

An accurate mathematical model of permanent magnet stepping motor is proposed. On the basis of this model, micro-stepping control is experimented. A comparison is made between the Data experimented by micro-stepping control and the data predicted by the proposed model and by Leenhouts' earlier model. The result shows that the proposed model is more accurate than the earlier model, and micro-stepping can be attained by dividing a given step electrically, without adding much complexity to the control circuit, or degrading the speed of stepping motors.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.88-90
• /
• 1994

The permanent magnet type stepping motor is used widly for various devices, such as FA and OA machine. Characteristics of the stepping motor is analyzed using permeance method. Static, dynamic and I step response characteristics of PM type stepping motor for idle air valve is discussed.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.929-931
• /
• 2004

Recently, there are growing demands for permanent magnet(PM) type stepping motor that greater mechanical output, smaller size. Especially, the PM type stepping motor with claw-poles is preferred solution for many small electronics position determination devices since it is small in size, low cost. But, the design of the PM type stepping motor with claw-poles is very difficult because it has a magnetic 3-D shape. This paper deals with a study of the miniaturization of the PM type stepping motor with claw-poles. We investigate the characteristic of the actual model using the equivalent magnetic circuit method and 3-D FE analysis.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2274-2277
• /
• 2003

A cylindrical permanent magnet inside the four-phase permanent magnet (PM) stepping motor is employed as the rotor. The stator has four teeth around, which its coils are wound. The mode of excitation can be classified into 3 modes: single-phase excitation, two-phase excitation and ministep excitation. The ministep drive is a method to subdivide one step into several small steps by means of electronics. The paper presents the programmable ministep technique drive. This technique decodes the results obtained from the counter to locate the data in Read Only Memory (ROM). The Sinusoidal Pulse Width Modulation (SPWM) is transformed to binary file and saved to the ROM. The experiment is performed with the four-phase PM stepping motor and drives from a two-phase programmable sinusoidal ministep signal, instead of square wave. The results show that the performances of the proposed programmable ministep technique drive have high efficiency, smooth step motion, and high speed response. Moreover, the resolution of sinusoidal ministep signal can be controlled by the input frequency (f command).

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.6-8
• /
• 2004

Recently, the PM type stepping motor preferred solution for many small electronics position determination devices since it is small in size. Thus, there are glowing demands for permanent magnet(PM) type stepping motor that greater mechanical output, smaller size. This paper deals with a study of the miniaturization of the PM type stepping motor with claw-poles. We introduced the small-sized PM type stopping motor that has new structure and analyzed the magnetic characteristic of it versus general type model using 3-D finite element analysis(FEA).

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.10
• /
• pp.507-513
• /
• 2003

Nowadays, the necessity of linear position control motors have been increased in the various fields of the automatic control system. In the recently, the position control motor have disadvantaged in the efficiency and economical view since it require a conversion equipments such as belt and gear in order to convert rotary to linear motion. On the contrary, the hybrid linear stepping motor(HLSM) of linear motion digital actuator has a direct drive method that do not need mechanical conversion equipments. Therefore, the HLSM is better advantaged in the efficiency and economical view than a rotary stepping motor. In this paper, we have designed an optimum tooth shape and a permanent magnet value between the mover teeth by the 2D finite element method(FEM) to develop the HLSM with longitudinal flux machine(LFM) type, and calculated the thrust force and normal force. And we have manufactured the prototype of it. and have experimented the thrust force and the dynamic thrust characteristics of it.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1261-1263
• /
• 2005

The micro permanent magnet(PM) type stewing motor preferred solution for many small electronics position determination devices since it is small in size. Thus, there are growing demands for PM type stepping motor that greater mechanical output, smaller size. But, the design of the it, having high performance and small size is very difficult because of its complex mechanical structure. This paper deals with a development of the newly structured micro PM type stepping motor with claw-poles. We introduced the small-sized PM type stepping motor that has new structure and analyzed the magnetic characteristic of it versus general type model using 3-D finite element analysis(FEA).