• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.2
• /
• pp.102-107
• /
• 2003

This study puts focus on the optimization of growth temperature of CIGS absorber layer which affects severely the performance of solar cells. The CIGS absorber layers were prepared by three-stage co-evaporation of metal elements in the order of In-Ga-Se. The effect of the growth temperature of 1st stage was found not to be so important, and 350$^{\circ}C$ to be the lowest optimum temperature. In the case of growth temperature at 2nd/3rd stage, the optimum temperature was revealed to be 550$^{\circ}C$. The XRD results of CIGS films showed a strong (112) preferred orientation and the Raman spectra of CIGS films showed only the Al mode peak at 173cm$\^$-1/. Scanning electron microscopy results revealed very small grains at 2nd/3rd stage growth temperature of 480$^{\circ}C$. At higher temperatures, the grain size increased together with a reduction in the number of the voids. The optimization of experimental parameters above mentioned, through the repeated fabrication and characterization of unit layers and devices, led to the highest conversion efficiency of 15.4% from CIGS-based thin film solar cell with a structure of Al/ZnO/CdS/CIGS/Mo/glass.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.11
• /
• pp.1148-1153
• /
• 2006

Signal measuring system to analyze ion concentrations in biofilm was constructed with ion selective microeleclrode and electrometer. In order to evaluate the performance and applicability of signal measuring system, the following characteristics, such as slope of calibration curve, detection limit, variation of response according to the time, and potentiometric selectivity coefficient, were investigated. The slope of calibration curve showed high degree of association for primary ion concentration. The response of the system was log-linear in standard solution down to $10{\mu}M$ and signal measuring system was not sensitive for interfering ions. In comparison with commercial electrometer, the fabricated electrometer system had similar tendencies for the slope of calibration curve, detection limit, and response time. Therefore the signal measuring system could be used to investigate ion profiles in biofilm as a cost effective and reliable measuring system.

• Journal of Microbiology and Biotechnology
• /
• v.23 no.1
• /
• pp.69-75
• /
• 2013

Enrofloxacin is a fluoroquinolone antibiotic approved for the treatment of infections in animals. Because of the side effects to consumers of animal products, the maximum residue limits (MRLs) of enrofloxacin in animal tissues for consumption are regulated. In this study, a monoclonal antibody (mAb) against enrofloxacin was prepared and characterized for the development of a direct competitive enzyme-linked immunosorbent assay (ELISA). The obtained mAb, Enro44, was highly specific for enrofloxacin and had a 50% inhibition concentration ($IC_{50}$) of 1.99 ng/ml in a competitive ELISA, and the limit of detection (LOD) was 0.50 ng/ml. The cross-reactivity of the mAb with other quinolones and fluoroquinolones was lower than 0.01%. The subclass of the mAb Enro44 was identified as IgG1. The antigen (Ag)-captured direct competitive ELISA using the mAb Enro44 was tested on different spiked samples, including chicken muscle, cattle milk, and cattle urine, and the assay demonstrated recoveries of 82-112%, 80-125%, and 78-124%, respectively. Furthermore, the quantitation of enrofloxacin obtained from the ELISA and from high-performance liquid chromatography (HPLC) was in good agreement, with the linear regression coefficient between 0.933 and 1.056. The cDNAs encoding a heavy-chain Fd fragment (VH and CH1) and a light chain of the mAb Enro44 were cloned and sequenced. Taken together, the results obtained reveal a potential use of this mAb in an ELISA for the detection of enrofloxacin in food samples. The information of amino acid sequence of this mAb will be useful for further modification and production of the mAb in a bioreactor.

• Membrane Journal
• /
• v.16 no.4
• /
• pp.276-285
• /
• 2006

Acid-doped sulfonated poly(aryl ether benzimidazole) (S-PAEBI) copolymers were synthesized by a direct polymerization technique and a doping with phosphoric acid as a dopant, and the polymer electrolyte membranes were fabricated from them by a solution casting method. To optimize the reaction condition, the degree of sulfonation and doping level were varied in the ranges of $0{\sim}60%\;and\;0.7{\sim}5.7$, respectively. Physiochemical properties of the doped membranes were investigated by AFM, TGA and the measurement of proton conductivity. It was found that proton conductivities depend on doping levels of membranes. Conductivity determined at the condition of $130^{\circ}C$ and no humidity was $7.3{\times}10^{-2}S/cm$ for the $H_3PO_4$-doped PAEBI membrane with a doping level of 5.7.

• Membrane Journal
• /
• v.25 no.5
• /
• pp.456-463
• /
• 2015

In this study, we synthesize novel silane based inorganics for preparation of the polymer electrolyte membrane with high proton conductivity under high temperature condition and developed membranes are characterized. SPAES, hydrocarbon based polymer are synthesized and used as main polymeric material. We used sol-gel method to prepare inorganic material with high performance using silica, phosphate and zirconium. Three types of inorganics were prepared by control of the mole ration of each component. As a result of EDX analysis, the inorganic materials are well dispersed in the polymer membrane. The water uptake of the composite membrane is increased by introduction of the hydrophilic inorganic material in the membrane. When the content of the zirconium in the membrane is increased, the proton conductivity of the composite membrane shows the higher value than pure SPAES membrane at the high temperature. And the silica based inorganics effect to increase the proton conductivity under low temperature condition.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.214.2-214.2
• /
• 2013

Device performance for the 45 and 32 nm node CMOS technology requires the integration of ultralow-k materials. To lower the dielectric constant for PECVD and spin-on materials, partial replacement of the solid network with air (k=1.01) appears to be more intuitive and direct option. This can be achieved introducting of second "labile" phase during depositoin that is removed during a subsequent UV curing and annealing step. Besides, with shrinking line dimensions the resistivity of barrier films cannot meet the International Technology Roadmap for Semiconductors (ITRS) requirements. To solve this issue self-forming diffusion barriers have drawn attention for great potential technique in meeting all ITRS requirments. In this present work, we report a Cu-V alloy as a materials for the self-forming barrier process. And we investigated diffusion barrier properties of self-formed layer on low-k dielectrics with or without UV curing treatment. Cu alloy films were directly deposited onto low-k dielectrics by co-sputtering, followed by annealing at various temperatures. X-ray diffraction revealed Cu (111), Cu (200) and Cu (220) peaks for both of Cu alloys. The self-formed layers were investigated by transmission electron microscopy. In order to compare barrier properties between V-based interlayer on low-k dielectric with UV curing and interlayer on low-k dielectric without UV curing, thermal stability was measured with various heat treatment temperature. X-ray photoelectron spectroscopy analysis showed that chemical compositions of self-formed layer. The compositions of the V based self-formed barriers after annealing were strongly dominated by the O concentration in the dielectric layers.

• Korean Journal of Materials Research
• /
• v.24 no.5
• /
• pp.243-248
• /
• 2014

Silicon-carbon composite was prepared by the magnesiothermic reduction of mesoporous silica and subsequent impregnation with a carbon precursor. This was applied for use as an anode material for high-performance lithium-ion batteries. Well-ordered mesoporous silica(SBA-15) was employed as a starting material for the mesoporous silicon, and sucrose was used as a carbon source. It was found that complete removal of by-products ($Mg_2Si$ and $Mg_2SiO_4$) formed by side reactions of silica and magnesium during the magnesiothermic reduction, was a crucial factor for successful formation of mesoporous silicon. Successful formation of the silicon-carbon composite was well confirmed by appropriate characterization tools (e.g., $N_2$ adsorption-desorption, small-angle X-ray scattering, X-ray diffraction, and thermogravimetric analyses). A lithium-ion battery was fabricated using the prepared silicon-carbon composite as the anode, and lithium foil as the counter-electrode. Electrochemical analysis revealed that the silicon-carbon composite showed better cycling stability than graphite, when used as the anode in the lithium-ion battery. This improvement could be due to the fact that carbon efficiently suppressed the change in volume of the silicon material caused by the charge-discharge cycle. This indicates that silicon-carbon composite, prepared via the magnesiothermic reduction and impregnation methods, could be an efficient anode material for lithium ion batteries.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.4
• /
• pp.435-442
• /
• 2004

This paper presents a hermetic MEMS on-chip package bonded by a closed-loop AuSn solder-line. We design three different package specimens, including a substrate heated specimen without interconnection-line (SHX), a substrate heated specimen with interconnection-line (SHI) and a locally heated specimen with interconnection-line (LHI). Pressurized helium leak test has been carried out for hermetic seal evaluation in addition to the critical pressure test for bonding strength measurement. Substrate heating method (SHX, SHI) requires the bonding time of 40min. at 400min, while local heating method (LHI) requires 4 min. at the heating power of 6.76W. In the hermetic seal test. SHX, SHI and LHI show the leak rates of 5.4$\pm$6.7${\times}$$^{-10}$ mbar-l/s, 13.5$\pm$9.8${\times}$$^{-10}$ mbar-l/s and 18.5$\pm$9.9${\times}$$^{-10}$ mbar-l/s, respectively, for an identical package chamber volume of 6.89$\pm$0.2${\times}$$^{-10}$. In the critical pressure test, no fracture is found in the bonded specimens up to the applied pressure of 1$\pm$0.1MPa, resulting in the minimum bonding strength of 3.53$\pm$0.07MPa. We find that the present on-chip packaging using a closed AuSn solder-line shows strong potential for hermetic MEMS packaging with interconnection-line due to the hermetic seal performance and the shorter bonding time for mass production.

• Food Science and Biotechnology
• /
• v.15 no.3
• /
• pp.392-398
• /
• 2006

Four flavonoids 1-4 and one phytosterol 5 were isolated from methanol extract of Taekwangkong, one of the soybean cultivars, and the structures of these compounds were fully characterized by physical and spectral analysis. The content of compounds 1-4 as determined by $C_{18}$ reversed phase HPLC (high-performance liquid chromatography) coupled with diode-array detector were 12.1, 624.6, 18.0, and $219.6\;{\mu}g/g$, respectively, and the total phenolic content of this cultivar was measured as 3.7 mg gallic acid equivalent per g dry material (GAB/g). Also, compound 1 showed strong radical scavenging activity in the 2,2'-azino-bis-(3-ethylbenzthiazoline-6-sulfonic acid) (ABTS) assay ($IC_{50}\;=\;47.6\;{\mu}M$), five-fold higher than seen in the 1,1-diphenyl-2-picrylliydrazyl (DPPH) assay. These results lead to the conclusion that soybean not only has many phytoestrogens but also has potent antioxidant activity.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.3
• /
• pp.408-415
• /
• 2014

In order to prepare high-quality activated carbons (ACs), coal tar pitch (CTP), and mixtures of CTP and petroleum pitch (PP) were activated with KOH. The ACs prepared by activation of CTP in the range of $700{\sim}1000^{\circ}C$ for 1~5 h had very porous textures with large specific surface areas of $2470{\sim}3081m^2/g$. The optimal activation conditions of CTP were determined as CTP/KOH ratio of 1:4, activation temperature of $900^{\circ}C$, and activation time of 3 h. The obtained AC showed the highest micro-pore volume, and pretty high specific surface area and meso-pore volume. The micro-pore volumes and specific areas of activated mixtures of CTP and PP were similar to each other but the meso-pore volume could be increased. In order to change the degree of crystallinity of precursors before KOH activation process, the CTPs were carbonized in the range of $500{\sim}900^{\circ}C$. As the carbonization temperature increased, the specific surface area and pore volume of the activated ACs with the same activation conditions for CTP decreased dramatically. It was demonstrated that the increased pore size distribution of AC electrodes in the range of 1 to 2 nm plays an important role in the performance of electric double-layer capacitor.