• International Journal of Automotive Technology
• /
• v.7 no.4
• /
• pp.493-500
• /
• 2006

Investigation on the fuel adhering on a wall was carried out experimentally to clarify the characteristics of impinging diesel sprays. Diesel sprays were injected into a high-pressure chamber of cold state and impinged to a wall having various impingement distances and ambient pressures. Photographs of both the fuel film and the post-impingement spray were taken through a transparent wall. Adhered fuel mass on a wall was measured by means of dividing into two types of fuel state: the fuel film itself; and sparsely adhered fuel droplets. Adhering fuel ratio was predicted and further the distribution of fuel mass for impinging diesel spray was analyzed as a function of time. As result, with an increase of the ambient pressure, both the maximum fuel film diameter and the adhered fuel ratio decreased. Based on some assumptions, the adhering fuel mass increased rapidly until the fuel film diameter approached the maximum value, and then increased comparatively gradually.

• Journal of Power Electronics
• /
• v.5 no.2
• /
• pp.83-98
• /
• 2005

As wind turbine technology and control has advanced over the last decade, this has led to a high penetration of wind turbines into the power system. Whether it be for a large wind turbine or an offshore wind farm with hundreds of MW power capacity, the electrical system has become more and more important in controlling the interaction between the mechanical system of the wind turbine and the main power system. The presence of power electronics in wind turbines improves their controllability with respect not only to its mechanical loads but also to its power quality. This paper presents an overview of a developed simulation platform for the modeling, design and optimization of wind turbines. The ability to simulate the dynamic behavior of wind turbines and the wind turbine grid interaction using four simulation tools (Matlab, Saber, DIgSILENT and HAWC) is investigated, improved and extended.

• Structural Engineering and Mechanics
• /
• v.12 no.2
• /
• pp.189-200
• /
• 2001

This paper presents an experimental modal analysis of perforated rectangular plates in air or in contact with water. The penetration of holes in the plates had a triangular pattern with P/D (pitch to diameter) 2.125, 2.500, 3.000 and 3.750. The plate was clamped along the plate edges by a number of bolts and nuts. The natural frequencies of the perforated plates in air were obtained by the analytical method based on the relation between the reference kinetic and maximum potential energies and compared with the experimental results. Good agreement between the results was found for the natural frequencies of the perforated plates in air. Additionally, it was empirically found that the natural frequencies of the perforated plate in air increase with an increase of P/D, on the other hand, the natural frequencies of the perforated plate in contact with water decrease with an increase of P/D.

• Structural Engineering and Mechanics
• /
• v.49 no.2
• /
• pp.163-182
• /
• 2014

Safety factors proposed in codes CEB, B.A.E.L 91 and EUROCODE 1 cover a great number of uncertainties; making them inadequate for the assessment of existing structures. Suitable safety factors are established using a probabilistic assessment, once real dimensions, materials strength and existing structures deterioration mechanisms are taken into account. This paper presents a calibration method for safety factors using a typical set of RC bridges in France. It considers the principal stages of corrosion provoked by $CO_2$ and $Cl^-$ penetration and threshold indexes (${\beta}_0$) for existing structures. Reliability indexes are determined by the FORM method in the calibration method.

• Journal of Welding and Joining
• /
• v.14 no.6
• /
• pp.81-92
• /
• 1996

This study is to compare the weldability of Zircaloy-4 end cap of nuclear fuel pin using by GTA and Nd :YAG LB. The welding parameters which affect bead width and penetration depth have been investigated. The effect of joint geometry of end cap for GTAW and LBW has been studied and optimum conditions of Zircaloy-4 endcap welding have been found. Microstructures and microhardness of GTA and LB welded zones have been also compared.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1312-1313
• /
• 2011

IT 산업의 발전에 따른 디지털 부하 증가는 기존 교류 배전 방식에서 DC 전원 공급에 따른 전력 변환 손실을 야기시킨다. 또한, 향후 신재생에너지를 통한 발전원 및 전기자동차의 계통 유입 확대로 인해 AC/DC 전력 변환에 따른 손실은 더욱 증대될 것으로 예상된다. 이에 본 논문에서는 DC 전원 공급율에 따른 전력 공급량 산정 기법을 제안한다. 또한, 탄소배출 비용을 함께 고려하여 DC 전원 공급율에 따른 신재생에너지 계통 연계의 경제적 타당성을 분석한다.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.482_483
• /
• 2009

This paper presents a method of finding the optimal operating point minimizing a given objective function with 3 phase power flow equations and operational constraints, called 3 phase optimal power flow. 3 phase optimal power flow can provide operation and control strategies for the distribution systems with distributed generation assets, which might be frequently in unbalanced conditions assuming that high penetration rate of renewable energy sources in the systems. As the solution technique, this paper adopts a standard particle swarm optimization (PSO).

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.320-323
• /
• 2006

A numerical study is made of a manifold and bipolar plate in polymer electrolyte fuel cells, the aim of the present study is to describe the characteristics of flow pattern In manifold and bipolar plate. The present work shows that the flow pattern in the bipolar plate is affected by the penetration flow through GDL characterized by clamping pressure and GDL intrusion in to a channel area. Manifold geometry also affects the flow distribution. The recirculation flow by bent duct destroy even distribution In manifold, the present work shows that corner rounding can improve the manifold performance.

• Journal of Pharmaceutical Investigation
• /
• v.38 no.5
• /
• pp.303-311
• /
• 2008

Highly hydrophobic lubricants including magnesium stearate may hinder water penetration into the tablet core resulting in delayed disintegration of fast disintegrating tablets. Alternative lubricants with equivalent lubricating properties may need to be incorporated into the tablet formulations. Sodium stearyl fumarate, glyceryl behenate and polyethylene glycol were evaluated regarding the tablet ejection energy, mechanical strength and disintegration time using Texture analyzer (TA). Resulting tablets were also compared with different particle sizes of granules and various compression forces. Among the tested lubricants, sodium stearyl fumarate was less sensitive to mixing time and also showed better or competitive tablet properties. During the experiments, TA was found to be very useful tool to investigate the tablet properties.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.8
• /
• pp.1059-1065
• /
• 2013

Doubly Fed Induction Generator(DFIG) systems occupy the largest proportion of worldwide wind energy generation market. DFIG systems are very sensitive to grid disturbances especially to voltage dips due to the structure of the stator connected to grid. In the past, when a grid fault occurs generators are separated from grid(trip method) in order to protect the systems. Nowadays, due to the growing penetration level of wind power, many countries have made some requirements that wind turbines are required to have Low Voltage Ride Through(LVRT) capability during grid faults. In this paper, a flux tracking LVRT control strategy based on system modeling equations is proposed. The validity of the proposed strategy is verified through computer simulations.