• 한국자동차공학회논문집
• /
• 제6권4호
• /
• pp.56-65
• /
• 1998

The bonding strength evaluation of the light weight materials for an electrical vehicle has been performed through the T-peel joint test in which the design paramete- rs such as joint style, adherend type, adherend thickness, adhesive thickness, and adhesive type are considered. It is experimentally observed that the peel strength of joint increases with the increase of the adherend thickness. With the increase of the adhesive thickness, however, the peel strength of joint increases a little. Aluminum-FRP adherend combination shows such higher peel strength than that of Aluminum-Aluminum adherend combination. For the adhesive bonded joint, the results of FEM analysis agree with those of experiment. The adhesive bonded joint reinfored with a rivet gives higher peel strength than that of the joint without rivet.

• 한국식품저장유통학회지
• /
• 제1권1호
• /
• pp.9-14
• /
• 1994

Soluble solids($^{\circ}$Brix), acid content and edible part ratio of Citrus unshiu collected at sorting Places in south Cheju area wee more lowered, and peel thickness was more thickened with increasing fruit size. Compared to early variety of Citurs unshiu(C. unshiu Miyakawa Mar), peel thickness of medium variety of Citurs unshiu(C. unshiu Hayashi Mar) was more thickened, and edible part ratio was more lowered with increasing fruit size. Soluble solids of medium variety of Citurs unshiu were lowered, and acid contents were increased compared to early variety. Processing properties for pressing concentrated juice was good for early variety of Citurs unshiu, especially on fruit diameter of 50-65mm. Soluble solids, acid contents and juice ratio were decreased with increasing peel thickness. The quality properties for fresh fruit with peel thickness had a good correlation on early variety of Citurs unshiu, and these data are supposed to be applied to the quality evaluation of Citurs unshiu produced in Cheju.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.166-173
• /
• 1998

The evaluation of joint fatigue strength of light weight materials for an electrical vehicle body has been performed through T-peel joint tests with the design parameters such as joint style, adherend type, adherend thickness, adhesive thickness, and various adhesives. Fatigue strength was evaluated through 5-Hz, tension-tension, load controlled test with the zero stress ratio. It was observed that the fatigue strength of the joint increases with the increase of the adherend thickness. With the increase of the adhesive thickness, however, the fatigue strength of the joint increases insignificantly. An aluminum-FRP adherend combination shows much higher fatigue strength than an aluminum-aluminum adherend combination. The results of fatigue tests were found to be consistent with those of static tests.

• 폴리머
• /
• 제38권3호
• /
• pp.397-405
• /
• 2014

본 연구는 고성능 준구조용 양면 점착테이프 제조를 위해 2-ethylhexyl acrylate(2-EHA)와 acrylic acid(AAC)를 사용하였고, UV 조사에 의해 시럽을 준비하였다. 양면 점착테이프의 두께, 무기물 충전제 함량 및 충전제 종류에 따른 준구조용 물성에 미치는 영향을 고찰하였다. 테이프의 두께 및 젖음시간이 증가할수록 박리강도가 증가하였다. 두께가 얇은 점착테이프($250{\mu}m$이하)의 경우 무기물 충전제의 true density가 낮을수록 적용시간 경과에 따라 박리강도가 높게 나타났다. 무기물 충전제 입자가 클수록 초기 박리강도가 높게 나타났으며, SEM 이미지를 통해 점착테이프 내에 무기물 충전제의 크기를 확인하였다. 다양한 무기물 충전제 및 함량에 따라 박리강도 증가와 함께 전단접착강도가 증가하는 비례관계를 보였으며, $0.1{\mu}m$인 양면 점착테이프에서 무기물 충전제는 전단접착강도에 더 영향을 주었다. 이러한 결과로부터 박막형 아크릴 양면 점착테이프는 준구조용 물성을 필요로 하는 용도에 사용가능할 것으로 사료된다.

• 한국재료학회지
• /
• 제15권7호
• /
• pp.458-464
• /
• 2005

In microelectronics packaging, the reliability of the metal/polymer interfaces is an important issue because the adhesion strength between dissimilar materials is often inherently poor. The modification of polymer surfaces by ion beam irradiation and rf plasma is commonly used to enhance the adhesion strength of the interface. T-peel strengths were measured using a Cu/polyimide system under varying $N_2^+$ ion beam irradiation conditions for pretreatment. The measured T-peel strength showed reversed camel back shape regarding the fixed metal-layer thickness, which was quite different from the results of the 90° peel test. The elementary analysis suggests that the variation of the T-peel strength is a combined outcome of the plastic bending work of the metal and polymer strips. The results indicate that the peel strength increases with $N_2^+$ ion beam irradiation energy at the fixed metal-layer thickness.

• 한국재료학회지
• /
• 제15권1호
• /
• pp.42-46
• /
• 2005

In microelectronics packaging, the reliability of the metal/polymer interfaces is an important issue because the adhesion strength between dissimilar materials is often inherently poor. The modification of polymer sufaces by ion beam irradiation and rf plasma are commonly used to enhance the adhesion strength of the interface. T-peel strengths were measured using a Cu/polyimide system under varying $Ar^+$ ion beam irradiation pretreatment conditions. The measured T-peel strength showed reversed camel back shape regarding the fixed metal-layer thickness, which was quite different from the results of the $90^{\circ}$ peel test. The elementary analysis suggests that the variation of the T-peel strength is a combined outcome of the plastic bending work of the metal and polymer strips. The results indicate that the peel strength increases with $Ar^+$ ion beam irradiation energy at the fixed metal-layer thickness.

• 한국식품저장유통학회지
• /
• 제7권4호
• /
• pp.357-361
• /
• 2000

밀병(watercore)은 과실의 저장 및 유통 산업에 있어서 큰 영향을 주므로 이를 비파괴측정할 수 있는 기술이 필요하다. 본 연구에서는 투광량을 이용한 사과의 밀병 판별 가능성과 밀병 판별에 영향을 미치는 인자들을 조사하였다. 사과의 화상데이터는 CCD 카메라를 사용하여 영상을 취득하였다. 밀병이 많이 든 사과는 밀병이 적게 든 사과보다 투광량이 더 많았으며 투광량에 의한 사과의 밀병 판별 정확도는 약 70%이었다. 사과의 과피두께, 색소층 두께, 과육밀도 등이 투광량에 영향을 미치는데 과피와 색소층의 두께가 얇고 과육밀도가 낮을수록 투광량은 높은 경향을 나타내었다. 사과의 착색정도가 좋을수록 밀병이 존재할 확률이 높았으며 착색분포는 밀병판별에 거의 영향을 주지 않는 것으로 나타났다.

• 한국의류학회지
• /
• 제23권1호
• /
• pp.22-29
• /
• 1999

This paper descrived the changes of peel strength wrinkle recovery and dimensional stability after fusing 4 different wool face fabrics with 3 different fusible interlinings. The fusing condition was conducted by fusing press machine under 4kg.f/cm2 at 15$0^{\circ}C$. To determine the effect of the varous physical properties of the fused fabrics face fabrics and interlinings on the peel strength wrinkle recovery and dimensional stability(hygral expansion and relaxation shrinkage) of fused fabrics correlation among the KES values of fused fabrics face fabrics and interlinings to the peel strength rinkle recovery and dimensional stability of fused fabrics were expeerimentally analyzed,. As the results the peel strength was mainly influenced by the cover factor of face fabric and interlinings. After fusing wrinkle recovery and hygral expansion were decreased. The cover factor wrinkle recovery weight thickness shear rigidity and frictional properties of face fabric and the thickness of fused fabrics were not influence to the wrinkle recovery of fused fabrics. In addition the dimensional stabilities of fused fabrics were mainly influenced by the tensile and frictional properties of the wrinkle recovery of fused fabrics. In addition the dimensional stabilities of fused fabrics were mainly influenced by the tensile and frictional properties of the face fabrics.

• Current Photovoltaic Research
• /
• 제11권2호
• /
• pp.44-48
• /
• 2023

In heterojunction technology (HJT) solar cells, low-temperature curing paste is used because the passivation layer deteriorates at high temperatures of 200℃ or higher. However, manufacturing HJT photovoltaic (PV) modules is challenging due to the weak peel strength between busbar electrodes and cells after soldering process. For this issue, the electrode thicknesses of the busbars of the HJT solar cell were analyzed, and the peel strengths between electrodes and wires were measured after soldering using an infrared (IR) lamp. As a result, the electrodes printed by the screen printing method had a difference in thickness due to screen mask. Also, as the thickness of the electrode increased, the peel strength of the wire increased.

• Current Photovoltaic Research
• /
• 제7권3호
• /
• pp.65-70
• /
• 2019

As a demand of higher power photovoltaic modules, shingled, multi-busbar, half-cell, and bifacial techniques are developed. Multi-busbar module has advantage for large amount of light havesting. And, half-cell is high power module for reducing resistive losses and higher shade tolerance. Recently, researches on multi-busbar is focused on reliability according to adhesion and intermetallic compound between Sn-Pb solder and Ag electrode. And half-cell module is researched to comparing with full-sized cell module for structure difference. In this study, we investigated the factors affecting to efficiency and adhesion of multi-wires half-cell module according to wire thickness, solder thickness, and flux. The results of solar simulator and peel test was that peel strength and efficiency of soldered cell is not related. But samples with flux including high solid material showed high efficiency. The results of FE-SEM and EDX line scan on cross-section between wire and Ag electrode for different flux showed thickness of solder joint between wire and Ag electrode is increasing through solid material increasing. Flux including high solid material would affect to solder behavior on Ag electrode. Higher solid material occurred lower growth of IMC layer because solder permeate to sider of wire ribbon than Ag electrode. And it increased fill factor for high efficiency. In soldering process, amount of solid material in flux and solder thickness are the factor related with characteristic of soldered photovoltaic cell.