• Journal of Advanced Marine Engineering and Technology
• /
• v.11 no.2
• /
• pp.71-81
• /
• 1987

Nowadays, the high development of industrial technique demands the optimal design of marine structures to be welded under the water, because the underwater welding of the ship hull and marine structures can decrease manpower and cost of production. However there is not available at present any report on fatigue behavior about underwater welded joints. In this paper under tention- tension repeated fatigue stress with frequency of 10 cycles per second by local controlled system, the fatigue strength properties of underwater welded joints of SM41A-2 Plate-to-Plate of 10 mm thickness were experimentally examined. The results obtained were as follows : 1) The fatigue strength of underwater welded joints of SM41A-2 was peaked at the heat input of about 1, 400 joule/mm(180 A, 36 V), while, at the heat input of more than about 1, 100 joule/mm (160 A, 33 V) that of the underwater welds at the higher than cycle of life rather than the lower cycle was higher than that of the base metal but lower than that of the atmosphere welds on account of both cooling and notch effects. 2) The fatigue limit of underwater welds increased with an increase of heat input resulting in a peak of that at the heat input of about 1, 400 joule/mm and then decreased gradually. 3) The fatigue strength at N cycles was peaked between the heat input of about 1, 400 and 1, 700 joule/mm where the strain was rapidly increased. 4) It was confirmed that the optimal zone of heat input condition for obtaining the underwater welds fatigue strength higher than that of the base metal exists, and if out of this zone, the fatigue strength of the underwater welds was lower than that of the base metal because of lack weld penetration, inclusion of slag, voids, etc. 5) By the fatigue test, the underwater welds fractured brittly without visual deformation, so the strain was remarkably less than of the atmosphere welds. 6) The fatigue life factor was peaked at the heat input of about 1, 600 joule/mm (200 A, 36 V) at which the mean strain is a little higher than that of the base metal but quite lower than those of the atmosphere welds, resulting in good underwater welds because both fatigue strength and ductility of the underwater welds are higher than those of the base metal at such heat input.

• Journal of the Korean Institute of Gas
• /
• v.16 no.6
• /
• pp.115-122
• /
• 2012

Polyurethane foams were synthesized with different contents and kinds of catalysts to know change of properties under various NCO index. UTM(universal testing machine), DSC(differential scanning calorimetry), SEM(scanning electron microscope) and FT-IR(Fourier transform spectroscopy) were used for studying the PUF's physical properties change. Compressive strength of PUF increased with increasing contents of catalyst. Glass transition temperature(Tg) and compressive strength of PUF using PC-8 and 33LV catalyst, increased with increasing NCO index at the aging. According to the results of Infrared spectral analysis, reduction of NCO peak was found in gelling catalyst, because unreacted NCO reacted with polyurethane. Although Tg and compressive strength of PUF using TMR-2, unchanged with increasing NCO index at the aging, because trimerization of isocyanate.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.639-646
• /
• 2000

It is important to estimate the mechanical properties of clay since it is directly related to the design and the construction of geotechnical structures. Site exploration, which is composed of boring, sampling, in-situ, or laboratory tests, is preformed to estimate the mechanical properties. However, mechanical properties of clay measured from laboratory test may be different from in-situ properties due to disturbances occurred during sampling, transportation, storage, and trimming. In this study, the degree of disturbance according to sampling method was estimated with the test results of CK/sub o/U triaxial compression test on Yangsan clay. The soil samples were obtained by three types of sampling method, j.e., 76mm-tube sampler, 76mm-piston sampler, and block sampler. In order to evaluate the quality of samples, volumetric strain, undrained shear strength, secant Young's modulus, and pore pressure coefficient at peak measured from each sample were compared with one another. From the test results, it was observed that mechanical properties of the block and piston samples were more reliable than those of tube samples. But it was observed that the water content of piston was similar to that of tube samples at given depths while the water content of block samples was 14.3∼15.8% smaller than that of piston and tube samples. In addition to the evaluation of the quality of samples, relationship between c/sub u// σ/sub vc/'and OCR was established from the results of the CK/sub o/U triaxial compression tests, which were carried out using SHANSEP method. And also undrained shear strength was analyzed using the in-situ test data such as Cone Penetration Test(CPT), Dilatometer Test(DMT), and Field Vane Test(FVT) and was compared with that evaluated from CK/sub o/U triaxial compression test.

• Economic and Environmental Geology
• /
• v.40 no.6
• /
• pp.771-784
• /
• 2007

This study shows the weathering characteristics of mica-schist affected by faulting and metamorphism through laboratory tests. Frozen-thaw test, which simulate the physical-chemical weathering processes in the laboratory, shows the important influence of foliation developed in mica-schist, resulting in $20{\sim}40%$ reduction of UCS according to weathering grade of rock. Slaking durability test was carried out for different weathering grade rock specimens and indicated that the specimens from fault area had a low durability index compared to other relatively fresh samples. XRD analysis allowed to estimate the dynamic evolution of mineral composition through wet-dry cycle in which the chlorite was the most important mineral leached out during slaking test. The creep test indicated that the main deformation produced along the foliation plane. The compacted clay minerals between discontinuity planes influence on the discontinuity shearing properties and result in a big difference between peak shear strength and residual strength. The results of laboratory tests on mica-schist show the possibility of a important deformation along the foliation plane or discontinuity.

• Tunnel and Underground Space
• /
• v.10 no.2
• /
• pp.165-172
• /
• 2000

When tunnels or underground structures are constructed in anisotropic rock mass, designers and constructors have to consider the anisotropic characteristics in rock mass because their physical and mechanical properties are depended on the anisotropic angles(${\beta}$). In this study, therefore, we have first investigated the mechanical behavior of the gneiss specimen from lab. tests, and then have analysed the behavior of specimens for to the transversely isotropic model in elastic medium using the FLAC program. The results of this study were summarized as follows; 1) In the result of the variation tests, in general, the properties of strength were depended on the angle of inclination in spite of the hard rock. And except for the shear strength test, the lowest and peak stress were appeared at 60$^{\circ}$ and 90$^{\circ}$respectively. 2) The results of specimen modeling analysis using FDM well indicated the mechanical behaviors of the specimen of transversely isotropic model.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.4
• /
• pp.361-369
• /
• 2012

In this study, prefabricated composite columns using high-strength angles (PSRC composite column) was studied. Concentric axial loading tests were performed for 2/3 scale PSRC specimens and an conventional SRC specimen with H-steel at the center of the cross-section. The test parameters were the steel ratio of angles and the spacing of lateral re-bars. The test results showed that by placing the angles at the corners of the cross-section for confinement with provided for the core concrete, the PSRC column specimens exhibited greater load-carrying capacity and deformation capacity than those of the conventional SRC column. The axial load-carrying capacity of the PSRC columns was greater than the prediction by KBC 2009. Using existing stress-strain relationship of confined concrete, the axial load-deformation relationship of the specimens were predicted. The numerical predictions correlated well with the test results in terms of initial stiffness, load-carrying capacity, and post-peak strength- and stiffness-degradations.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.8
• /
• pp.15-25
• /
• 2013

In order to examine the unsaturated shear strength characteristics of compacted weathered gneiss soils, the constant water content compression (CWCC) test was carried out. Specimens were made by static compaction under two densities conditions. The shear behavior in accordance with an initial suction obtained by varying initial degrees of saturation was evaluated. The suction could be directly measured by the use of the ceramic disk and the pore-water pressure transducer. The results of the peak shear strength from the CWCC test were examined using the relationship with Mp line from triaxial test under the saturated state, that is, by means of the suction stress which was calculated using the measured suction. In addition, the applicability of the suctions stress to the unsaturated shear behaviour of compacted weathered gneiss soils was discussed by applying Suction stress-SWCC Method (SSM).

• Tunnel and Underground Space
• /
• v.8 no.3
• /
• pp.234-248
• /
• 1998

This paper presents a new constitutive model for numerical modeling the shear behaviour of rough rock joints. The model incorporates the dilatancy of joints on the basis of elasto-plastic theory. Barton's empirical shear strength formular are adopted in the formulation process. The mobilized JRC concept is evoked to address the shear strength hardening and sofrening phenomena. The mobilized JRC in the pre- and post-peak range is approximated by assuming that the variation of JRC is a function of tangential plastic work. Discrete finite joint element is used to implement the proposed constitutive model. The model is validated by the numerical direct shear test on a single joint which is subjected to different boundary conditions. The test results are in good agreement with the experimental observations reported by other authors. The numerical tests also exhibit that the proposed model can simulate the salient features envisaged in the behaviour of rough rock joints.

• Journal of the Korean Society of Physical Medicine
• /
• v.13 no.1
• /
• pp.121-128
• /
• 2018

PURPOSE: This study assessed the effect of exercise intervention methods on diaphragm movement, pulmonary function, and pulmonary strength in children with cerebral palsy (CP). METHODS: A total of 28 children with CP were randomly allocated to the general exercise group (n=9, GEG), respiratory exercise group (n=10, REG), and intensive exercise group (n=9, IEG). The exercise intervention was performed for 12 weeks. This study measured diaphragm movement, pulmonary function, and pulmonary strength under two different conditions before and after each exercise. Ultrasonography was used for measuring diaphragm movement, and Pony Fx was used to measure the forced expiratory volume in one second ($FEV_1$), peak expiratory flow (PEF), maximum inspiratory pressure (MIP), and maximum expiratory pressure (MEP). A Mann-Whitney test and ANOVA with a significance level of .05 were used for statistical analysis. RESULTS: Significant change was observed between the REG and the IEG as well as between the GEG and the IEG (p<.05). No significant difference was observed between the GEG and the REG. The diaphragm movement, $FEV_1$ PEF, MIP, and MEP were most improved in the IEG (p<.01). CONCLUSION: This study confirmed that intensive exercise is the most effective treatment method for improving diaphragm movement and respiratory function in CP children.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.83-93
• /
• 2003

This research, in order to study the effects of initial shear stress of anisotropically consolidated sand that has 0.558% fines, performed several undrained static and dynamic triaxial test. To simulate the real field conditions, loose and dense samples were prepared. Besides, the cyclic shear strength of Nakdong River sand under various combinations of initial static shear stress, stress path, pore water pressure and residual strength relationship was studied. By using Bolton's theory, peak internal friction angle at failure which has considerable effects on the relative density and mean effective stress was determined. In p'- q diagram, the phase transformation line moves closer to the failure line as the specimen's initial anistropical consolidation stress increases. Loose sands were more affected than dense sands. The increase of consolidation stress ratio from 1.4 to 1.8 had an effect on liquefaction resistance strength resulting from the increase of relativity density, and showed similar CSR values in dense specimen condition.