• Journal of Biomedical Engineering Research
• /
• v.18 no.1
• /
• pp.25-36
• /
• 1997

To regulate cardiac output of the Total Artificial Heart(TAH) physiologically, the hemodynamic information must be toed back to the controller. So far, our group has developed an automatic cardiac output control algorithm using the motor current waveform, It is, however difficult to detect the preload level such as a filling status of ventricular inflow and the variation of atrial pressures within normal physiologic range(0-15 mmHg) by analyzing the motor current which simultaneously reflects the afterload effect. On the other hin4 the interventricular volume pressure(IVP) which is not influenced by arterload but by preload is a good information source for the estimation of preload states. In order to find the relationship between preload and IVP waveform, we set up the artificial heart system on the Donovan type mock circulatory system and measured the IVP waveform, right and left atrial pressures, inflow and outflow waveforms and the signals represented the information of moving actuator's position. We shows the feasibility of estimating the hemodynamic changes of inflow by using IVP waveform. fife found that the negative peak value of IVP waveform is linearly related to atrial pressures. And we also found that we could use the time to reach the negative peak in IVP waveform, the time to open outflow valve, the area enclosed IVP waveform as unfu parameters to estimate blood filling volume of diastole ventricle. The suggested method has advantages of avoiding thrombogenesis, bacterial niche formation and increasing longterm reliability of sensor by avoiding direct contact to blood.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.8
• /
• pp.581-586
• /
• 1998

This paper describes athermally stimulated displacement current (TSDC) of arachidic acid(AA) and polyamic acid alkylamine salts(PAAS) Langmuir-Blodgett(LB) films, which is a precursor of polyimide(PI). The TSDC measurements of AA LB film were performed from temperature to about 11$0^{\circ}C$ at a rate of 0.2$^{\circ}C$/ｓ inside a vacuum chamber for a reference. And the TSDC measurements PAAS LB film were performed from room temperature to about 25$0^{\circ}C$ and temperature was increased at the same rate as that of AA LB film. They show that there are TSDC peaks at about 7$0^{\circ}C$ in the arachidic acid LB films, and at about 7$0^{\circ}C$ and 16$0^{\circ}C$ in the PAAs LB films. Results of these measurements indicate the one small peak at 7$0^{\circ}C$ is resulted from a softening of the alkyl group and the large peak at 16$0^{\circ}C$ is possibly due to dipole of C-O group in the PASS molecule. We have calculated the vertical component of the AA and PAAs L film out of the TSDC curves. It shows that the dipole moment of the AA LB film is about 70-mD at 7$0^{\circ}C$. And the dipole moment of PAAS LB film is about 040mD at 7$0^{\circ}C$ and about 200mD at 16$0^{\circ}C$ in the first measurement of TSDC. In the second measurement of TSDC of PASS LB film after cooling down to room temperature, the TSDC peaks are almost disappeared.

• Journal of the Semiconductor & Display Technology
• /
• v.11 no.3
• /
• pp.33-37
• /
• 2012

Simple and high efficiency blue organic light-emitting diodes with three organic layers of N, N'-diphenyl-N,N'-bis-[4-(phenyl-m-tolylamino)-phenyl]-biphenyl-4,4'-diamine[DNTPD]/1,1-bis-(di-4-polya-minophenyl)cyclohexane[TAPC]/electron transport material [ET-137] were fabricated and their electroluminescent characteristics were evaluated according to the TAPC thickness variation in a range of $50{\sim}300{\AA}$. Electroluminescence spectra of the devices with structure of DNTPD/TAPC/ET-137 showed all the same central emission wavelengths of 455 nm under an applied voltage of 7V, which were similar with that of the device with ET-137 only. On the other hand, the electroluminescence spectra of the device with structure of DNTPD/ET-137 without TAPC layer showed double emission peaks at the wavelengths of 455 nm and 561 nm under an applied voltage of 7V. In the devices with structure of DNTPD/TAPC/ET-137, single peak blue emission was not maintained in the device with $50{\AA}$-thick TAPC above 8V by the formation of exciplex. In the device with $300{\AA}$-thick TAPC, however, single peak blue emission was maintained until 10 V. According to the thickness increase of TAPC in the fabricated devices, the current density and luminance decreased, but the luminous efficiency and roll-off characteristics were improved.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.1
• /
• pp.130-136
• /
• 2008

This paper describes a low-power high-performance analog front-end block for $UHF(860{\sim}960MHz)$ band RFID tag chips. It satisfies ISO/IEC 18000-6 type C(EPCgolbal class1. generation2.) and includes a memory block for test. For reducing power consumption, it operates with a internally generated power supply of 1V. An ASK demodulator using a current-mode schmitt trigger is proposed and designed. The proposed demodulator has an error rate as low as 0.014%. It is designed using a 0.18um CMOS technology. The simulation results show that the designed circuit can operate properly with an input as low as $0.2V_{peak}$ and consumes $2.63{\mu}A$. The chip size is $0.12mm^2$

• Wind and Structures
• /
• v.29 no.5
• /
• pp.339-359
• /
• 2019

Pre-stressed concrete poles are among the supporting systems used to support transmission lines. It is essential to protect transmission line systems from harsh environmental attacks such as downburst wind events. Typically, these poles are designed to resist synoptic wind loading as current codes do not address high wind events in the form of downbursts. In the current study, the behavior of guyed pre-stressed concrete Transmission lines is studied under downburst loads. To the best of the authors' knowledge, this study is the first investigation to assess the behaviour of guyed pre-stressed concrete poles under downburst events. Due to the localized nature of those events, identifying the critical locations and parameters leading to peak forces on the poles is a challenging task. To overcome this challenge, an in-house built numerical model is developed incorporating the following: (1) a three-dimensional downburst wind field previously developed and validated using computational fluid dynamics simulations; (2) a computationally efficient analytical technique previously developed and validated to predict the non-linear behaviour of the conductors including the effects of the pretension force, sagging, insulator's stiffness and the non-uniform distribution of wind loads, and (3) a non-linear finite element model utilized to simulate the structural behaviour of the guyed pre-stressed concrete pole considering material nonlinearity. A parametric study is conducted by varying the downbursts locations relative to the guyed pole while considering three different span values. The results of this parametric study are utilized to identify critical downburst configurations leading to peak straining actions on the pole and the guys. This is followed by comparing the obtained critical load cases to new load cases proposed to ASCE-74 loading committee. A non-linear failure analysis is then conducted for the three considered guyed pre-stressed concrete transmission line systems to determine the downburst jet velocity at which the pole systems fail.

• Journal of the Korea Society of Computer and Information
• /
• v.11 no.4 s.42
• /
• pp.77-85
• /
• 2006

There is the spatial correlation of the video sequence between the motion vector of current blocks. In this paper, we propose the enhanced fast block matching algorithm using the spatial correlation of the video sequence and the center-biased properly of motion vectors. The proposed algorithm determines an exact motion vector using the predicted motion vector from the adjacent macro blocks of the current frame and the Cross-Hexagonal search pattern. From the of experimental results, we can see that our proposed algorithm outperforms both the prediction search algorithm (NNS) and the fast block matching algorithm (CHS) in terms of the search speed and the coded video's quality. Using our algorithm, we can improve the search speed by up to $0.1{\sim}38%$ and also diminish the PSNR (Peak Signal Noise Ratio) by at nst $0.05{\sim}2.5dB$, thereby improving the video qualify.

• Journal of Convergence for Information Technology
• /
• v.11 no.7
• /
• pp.104-110
• /
• 2021

A novel selective oxidation process has been developed for low source/drain (S/D) series resistance of the fin channel metal oxide semiconductor field effect transistor (MOSFET). Using this technique, the selective oxidation fin-channel MOSFET (SoxFET) has the gate-all-around structure and gradually enhanced S/D extension regions. The SoxFET demonstrated over 70% reduction in S/D series resistance compared to the control device. Moreover, it was found that the SoxFET behaved better in performance, not only a higher drive current but also higher transconductances with suppressing subthreshold swing and drain induced barrier lowering (DIBL) characteristics, than the control device. The saturation current, threshold voltage, peak linear transconductance, peak saturation transconductance, subthreshold swing, and DIBL for the fabricated SoxFET are 305 ㎂/㎛, 0.33 V, 13.5 𝜇S, 76.4 𝜇S, 78 mV/dec, and 62 mV/V, respectively.

• Journal of Coastal Disaster Prevention
• /
• v.4 no.4
• /
• pp.189-196
• /
• 2017

Ocean Research Stations (ORSs) is the ocean platform type observation towers and measured oceanic, atmospheric and environmental data. These station located on the offshore area far from the coast, so they can produce the data without land effect. This study focused to improve the wave data quality of ORS station. The wave observations at ORSs are used by the C-band (5.8 GHz, 5.17 cm) MIROS Wave and Current Radar (MWR). MWR is convenient to maintenance and produce reliability wave data under bad weather conditions. MWR measured significant wave height, peak wave period, peak wave direction and 2D wave spectrum, so it's can provide wave information for researchers and engineers. In order to improve the reliability of MWR wave data, Datawell Waverider Buoy was installed near the one ORS (Socheoncho station) during 7 months and validate the wave data of MWR. This study found that the wave radar tend to be overestimate the low wave height under wind condition. Firstly, this study carried out the wave Quality Control (QC) using wind data, however the quality of wave data was limited. So, this study applied the four filters (Correlation Check, Direction Filter, Reduce White Noise and Phillips Check) of MWR operating software and find that the filters effectively improve the wave data quality. After applying 3 effective filters in combination, the RMSE of significant wave height decreased from 0.81m to 0.23m, by 0.58m and Correlation increased from 0.66 to 0.96, by 0.32, so the reliability of MWR significant wave height was significantly improved.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.4
• /
• pp.431-437
• /
• 2022

As one of the most hazardous and deadliest pathogens, Listeria monocytogenes (LM) posed various serious diseases to the human being, thus designing effective strategy for its detection is of great significance. In this work, by preparing Ti₃C₂T_x MXenes nanoribbon (Ti₃C₂T_xR) as carrier and selecting thionine (Th) acted simultaneously as signal probe and functional monomer, a LM pathogen-imprinted polymers (PIP) integrated probe electrochemical sensor was design to monitor LM for the first time, that was carried out through the electropolymerization of Th on the Ti₃C₂T_xR/GCE surface in the existence of LM. Upon eluting the templates from the LM imprinted cavities, the fabricated PIP/Ti₃C₂T_xR/GCE sensor can rebound LM cells effectively. By recording the peak current of Th as the response signal, it can be weakened when LM cell was re-bound to the LM imprinted cavity on PIP/Ti₃C₂T_xR/GCE, and the absolute values of peak current change increase with the increasement of LM concentrations. After optimizing three key parameters, a considerable low analytical limit (2 CFU mL^-1) and wide linearity (10-10⁸ CFU mL^-1) for LM were achieved. In addition, the experiments demonstrated that the PIP/Ti₃C₂T_xR sensor offers satisfactory selectivity, reproducibility and stability.

• Korean Journal of Agricultural Science
• /
• v.49 no.4
• /
• pp.1033-1040
• /
• 2022

The current experiment was conducted to evaluate the effect of diallel crossbreeding on the body weight and laying performance of Korean native chicken from hatch to week 40. A total of 1,000 one-day-old chicks were allotted to 10 cages per crossbreeding treatment with 10 birds per cage on a random basis and then raised until 16 weeks and subsequently moved to layer battery cages and raised until 40 weeks. Ten crossbred treatments (YC, YD, YF, YK, CD, CF, CK, DF, DK, FK) that were obtained from the diallel crossbred of five pure lines were used in the current experiment. The body weight and mortality were measured biweekly from hatching to week 20 and every four weeks from week 20 to week 40. The number of eggs was measured daily. YC and YD crossbreeds showed a higher body weight (p < 0.05) and FK crossbreed showed a lower body weight (p < 0.05) during the whole xperimental period. The week 20 weight range was 1,501 to 1,729 g and the week 40 weight range was from 1,829 to 2,179 g. Earlier onset of egg-laying was noted in the YC and YD groups whereas late onset was observed for the DF and DK groups. YK reached its peak earliest at week 25 with 89.15% while the DK crossbreed attained its peak at week 36 with 89.69%. The YC and YD crossbreeds showed the improved body and egg-laying performance. Conclusively, there are variations in the body weight and laying performance of Korean native chickens with diallel crossing.