• Current Optics and Photonics
• /
• v.7 no.3
• /
• pp.248-253
• /
• 2023

An efficient global optimization approach for a periodic plasmonic nanoslit array based on extraordinary optical transmission within an acceptable time range is proposed using 𝚀 factor analysis method. The particle swarm optimization is employed as a global optimization tool. The figure of merit is defined as a product of transmission peak value and 𝚀 factor. The design variables are the slit width, height, and period of the slit array, respectively. The optical properties such as transmission spectrum and bandwidth are calculated rigorously using the finite element method.

• Journal of the Korean Vacuum Society
• /
• v.21 no.3
• /
• pp.164-170
• /
• 2012

The dependance of degradation on the blue-peak wavelength is investigated with the blue light-emitting diode (LED) of InGaN/GaN with respect to the optical and the electrical characteristics of the devices. The LED devices emitting the blue-peak wavelength ranging from 437 nm to 452 nm is prepared to be stressed for a long aging time with three different currents of 60 mA, 75 mA and 90 mA, respectively. The degradation of optical intensity is observed with and without phosphor in the devices. The device without phosphor has been degraded significantly as the wavelength of blue-peak is decreased while the optical intensity of LED device with phosphor become less sensitive than that of device without phosphor. The electrical property does not depend on the emission peak wavelength. However, the series-resistance of LED device is slowly increased as the aging time is increased. The deformation of device is observed severely the short wavelength of blue-peak even with the same current since the short wavelength is absorbed substantially at the materials of device during the aging time. Consequently, in order to enhance the lifetime of LED devices, it is important to understand the optical degradation property of the materials against the specific wavelengths emitted from the blue chip.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.11
• /
• pp.167-174
• /
• 1996

For the decreasing of switching loss, this paper designs the improved buck converter circuit and then compare with the conventional buck converter and finally analyzes the performance. When the switch is turn-off, in the buck converter using the smoothing capacitor, the flow of transient current and peak voltage having the high frequency components was generated because of the instantaneous open-state in the teminals of the switch. However, the buck converter presented in this paper eliminated this disadvantage by using the L-C circuit. Therefore, the higher PF in 0.85 is achieved than that of the buck converter using the smoothing capacitor. Also, due to the decreasing of the harmonic contain rate, the current usage rate is to be higher than that of the conventional buck converter by 4.48dB and the output voltage varient rate for the step response is to be lower 1.32 times than that of the conventional buck converter.

• Electrical & Electronic Materials
• /
• v.9 no.2
• /
• pp.165-173
• /
• 1996

We prepared polythiophene and poly(3-methylthiophene) films, known as conducting polymer, by electrochemical method. Polythiophene and poly(3-methylthiophene) films were doped and undoped dopant for the studing the understanding of doping mechanism and possible application to the color change switch. We observed that the anodic, cathodic wave and absorption spectra were slightly changed during doping and undoping process in polythiophene. It shows that doping and undoping process were showed some difference by the appearance and disappearance of polaron and bi-polaron. In the relation of the peak of oxidative current density and potential sweep rate of cyclic voltammograms, the amount of dopant in polythiophene film was homogeneously increased at low scan rate. This also can be applied to the poly(3-methlythiophene).

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.583-585
• /
• 2004

In this paper we will deal with a calibration method for low cost motion capture system using psd(position sensitive detection) optical sensor. To measure the incident direction of the light from LED emitted marker, the PSD is used the output current ratio on the electrode of PSD is proportional with the incident position of the light focused by lens. In order to defect the direction of the light, the current output is converted into digital voltage value by opamp circuits peak detector and AD converter with the digital value the incident position is measured. Unfortunately, due to the non-linearly problem of the circuit poor position accuracy is shown. To overcome such problems, we compensated the non-linearly by using least-square fitting method. After compensated the non-linearly in the circuit, the system showed more enhanced position accuracy.

• Journal of Welding and Joining
• /
• v.14 no.6
• /
• pp.48-57
• /
• 1996

The weldability of high purity aluminum-lithium binary alloys has been investigated using the Varestraint test. Autogenous GTAW (gas-tungsten-arc-welds) were run along specimens of different lithium concentration using three sets of welding parameters. Welding voltage was held constant at 10 volts. Welding current (70∼100 amps) and travel speed (23∼33 cm/min) were the parameter varied. Hot-tearing susceptibility varied with lithium content and exhibited a steep peak at 2.6 weight percent lithium. Depth of penetration increased with increasing heat input and lithium concentration. The susceptibility is influenced by the wettability of dendrites by the interdendritic eutectic liquid as well as the time available for back-Siting by eutectic liquid. The welding condition of welding current 70A and travel speed 23 cm/min was showed good resistance to cracking in aluminum-lithium alloys. Suggestions for improving weld cracking resistance are also provided.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.665-669
• /
• 2000

Recently the problem of energy branch become worse increasingly. Therefore many researches about new energy source are processing in several places around are processing in several places around the world. Especially solar energy has many advantages like as purity and infinity. Photovoltaic(PV) system can be classified into two types : One is stand alone type and the other is utility interactive one. Utility interactive type PV system need some technology that Maximum peak power tracking(MPPT) and Anti-islanding and Active Power filter(APF). For APF operation dc-link voltage should be high to supply sufficient output current which needed for harmonic current compensation so usually DC-DC converter is used for boost. In this paper DC-DC converter for PV system and controller for dc-link voltage control are analyzed and designed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.9 no.3
• /
• pp.132-139
• /
• 1984

This paper presents an exant analysis of the class E tuned power amplifier with a shunt inductor. The following performance parameters are determined for optimum operation with any switch duty ratio: the collector current and voltage waveforms, the peak values of collector current and voltage, the output power, the power output capability, and the values of the load network elements. The analysis shows that the maximum power output capability occurs at a duty ratio of 50 percent. The measured collector efficiency of experiments is 93 percent with 0.93W at 1MHz. This amplifier is especially applicable at portable transmitters because its colletor efficiency is extremely high.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.498-499
• /
• 2011

In this paper, the fundamental features of the arc stability DC arc furnace have been investigated, from the converter point of view. To compare of measurement arc data from DC arc furnace and the advanced arc simulations of magneto-hydrodynamics (MHD) and the well known Cassie-Mayr arc model have been extensively used. The MHD based arc simulation has been validated in the subcomponent level, for the free burning arc set up in the laboratory. The arc simulation predicted the arc voltage for different currents with the accuracy which satisfies engineering requirements. It has been shown that the arc current steepness at current zero determines the arc stability, and the associated peak arc resistance can be used as its quantitative measure. Based on the presented insight into the DC arc stability, a converter topology solution which realizes an optimal arc stability has been proposed. The main results presented in this paper provide a design guideline for the future DC arc furnace converter topology developments.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.1
• /
• pp.40-45
• /
• 2008

This paper presents an optimal design of a permanent magnet actuator(PMA) using a parallel genetic algorithm. Dynamic characteristics of permanent magnet actuator model are analyzed by coupled electromagnetic-mechanical finite element method. Dynamic characteristics of PMA such as holding force, operating time, and peak current are obtained by no load test and compared with the analyzed results by coupled finite element method. The permanent magnet actuator model is optimized using a parallel genetic algorithm. Some design parameters of vertical length of permanent magnet, horizontal length of plunger, and depth of permanent magnet actuator are predefined for an optimal design of permanent magnet actuator model. Furthermore dynamic characteristics of the optimized permanent magnet actuator model are analyzed by coupled finite element method. A displacement of plunger, flowing current of the coil, force of plunger, and velocity of plunger of the optimized permanent magnet actuator model are compared with the results of a primary permanent magnet actuator model.