• The Journal of Engineering Geology
• /
• v.34 no.2
• /
• pp.317-327
• /
• 2024

When a non-persistent joint system is formed in a large-scale rock slope, slope failure may occur due to presence of a the stepped sliding surface. Such a surface can be divided into joint-to-joint sliding surfaces or joint-to-rock bridge sliding surfaces. In the latter case, the rock bridge provides shear resistance parallel to the joint and tensile resistance perpendicular to the joint. The load of the sliding rock can lead to failure of the rock bridge, thereby connecting the two joints at each ends of the bridge and resulting in step-path failure of the slope. If each rock bridge on a slope has the same length, the tensile strength is lower than the shear strength, resulting in the rock bridges oriented perpendicular to the joint being more prone to failure. In addition, the smaller the ratio of discontinuity spacing to length, the greater the likelihood of step-path failure. To assess the risk of stepped sliding on a rock slope with non-persistent joints, stability analysis can be performed using limit equilibrium analysis or numerical analysis. This involves constructing a step-path failure surface through a systematic discontinuity survey and analysis.

• Physical Therapy Rehabilitation Science
• /
• v.8 no.3
• /
• pp.141-145
• /
• 2019

Objective: The purpose of this study was to compare walking conditions (straight line and curved path) on walking patterns in persons who had experienced hemiplegic stroke and to determine whether if they adapt their walking pattern and performances according to changes in environmental conditions. Design: Cross-sectional study. Methods: Forty-four hemiplegic stroke survivors participated in this study. This study measured walking performance in three different walking conditions, such as straight walking, the more-affected leg in the inner curve walking, and less-affected leg in the inner curve walking conditions, and a 2-dimentional gait analysis system was used as a primary measurement. This study also measured secondary clinical factors including the Timed Up-and-Go Test, the Trunk Impairment Scale, and the Dynamic Gait Index. Results: After analyzing, cadence and step length of the less-affected side, stride length in the more-affected side, and stride length in less-affected side were significantly different among the three different walking conditions in this study (p<0.05), but other temporospatial parameters were not significant. Cadence was the largest in the straight walking condition. Step length in the less-affected side, stride length in the more-affected side, and stride length in less-affected side were also the longest in the straight walking condition. Conclusions: The results of the study suggest that hemiplegic stroke survivors show walking adaptability according to changes in walking demands and conditions, and moreover, cadence and step and stride lengths were significantly different between straight and curved walking conditions.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.25 no.4
• /
• pp.39-46
• /
• 1988

The purpose of this paper is to apply the boundary element method to predict the crack growth path. The quarter point element with traction singularity at the crack tip is applied to compact tension type specimens and two inclined slit problems under compression load. The maximum stress criterion which was originally derived for the crack initiation is extended to the analysis of the crack propagation. The predicted crack paths with 1/4 crack growth increment of initial crack length agree quite well with experimental results. It is found that the computed crack path of the boundary element analysis is not mainly affected by the crack increment length.

• Journal of Institute of Convergence Technology
• /
• v.1 no.1
• /
• pp.29-33
• /
• 2011

This study is performed to investigate the effect of the artificial light for room lightening. To do that, the experiments were done using the black room with 1m3 and performed to show the effect of the length between the room and light source and light intensities as LUX. The LUX of 18 sites in the room was measured using LUX meter. The length between the room and the light source was chosen as 500mm, 1000mm, and 1500mm and the light intensities was 3 levels. The results were shown the distinct difference between the part directly projected through the light path and non-directly projected. So, the light delivery path have to be modified for next step research. The results were very sensitive for the part directly projected through the light path. This study showed the basic results for room lightening using light source to simulate the solar lightening and was worth in a strict sense as fundamental study.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.9
• /
• pp.142-150
• /
• 2002

This study describes a method of finding an optimal path of a soccer robot by using a concentric circle method with different radii of rotation. Comparing with conventional algorithms which try to find the shortest path length, the variable concentric circle method find the shortest moving time. The radius fur the shortest moving time for a given ball location depends on the relative location between a shooting robot and a ball. Practically it is difficult to find an analytical solution due to many unknowns. Assuming a radius of rotation within a possible range, total path moving time can be calculated by adding the times needed for straight path and circular path. Among these times the shortest time is obtained. In this paper, a graphical solution is presented such that the game ground is divided into 3 regions with a minimum, medium, and maximum radius of rotation.

• Journal of the military operations research society of Korea
• /
• v.26 no.2
• /
• pp.120-130
• /
• 2000

The purpose of this study is to present a method for determining the k most vital arcs in shortest path problem using an evolutionary algorithm. The problem of finding the k most vital arcs in shortest path problem is to find a set of k arcs whose simultaneous removal from the network causes the greatest increase in the total length of shortest path. Generally, the problem determining the k most vital arcs in shortest path problem has known as NP-hard. Therefore, in order to deal with the problem of real world the heuristic algorithm is needed. In this study we propose to the method of finding the k most vital arcs in shortest path problem using an evolutionary algorithm which known as the most efficient algorithm among heuristics. The method presented in this study is developed using the library of the evolutionary algorithm framework and then the performance of algorithm is analyzed through the computer experiment.

• The Journal of Korean Physical Therapy
• /
• v.26 no.6
• /
• pp.459-463
• /
• 2014

Purpose: The purpose of this study was to investigate the correlations between functional movement screen (FMS) and ankle dysfunctions in subjects with chronic ankle instability (CAI). Methods: This study was a cross-sectional study of 20 participants with CAI. The ankle dorsiflexion range of motion (ROM), Foot and Ankle Disability Index (FADI), center of pressure (COP) path length, and COP velocity for ankle dysfunction were measured in all the subjects. All the subjects underwent the FMS concerned with ankle functions consisted of deep squats, hurdle steps and in-line lunges. The Spearman rank-order correlation coefficient was used to determine relationship between the ankle ROM, FADI, COP and FMS. Results: The results of the deep squat and in-line lunge exercises revealed a significant correlation with the ankle dorsiflexion ROM, FADI, COP path length, and COP velocity. The hurdle step showed no correlation with the ankle dorsiflexion ROM and FADI but a significant relationship with the COP path length and COP velocity. Conclusion: The results of this study showed that relationship deep squat and in-line lunge and it is suggested that an assessment tool using ankle dorsiflexion ROM and ankle instability would be clinically effective.

• Journal of Mechanical Science and Technology
• /
• v.18 no.1
• /
• pp.92-105
• /
• 2004

A new algorithm for planning a collision-free path based on algebraic curve is developed and the concept of collision-free Path Space (PS) is introduced. This paper presents a Geometry Mapping (GM) based on two straight curves in which the intermediate connection point is organized in elliptic locus ($\delta$, $\theta$). The GM produces two-dimensional PS that is used to create the shortest collision-free path. The elliptic locus of intermediate connection point has a special property in that the total distance between the focus points through a point on ellipse is the same regardless of the location of the intermediate connection point on the ellipse. Since the radial distance, a, represents the total length of the path, the collision-free path can be found as the GM proceeds from $\delta$=0 (the direct path) to $\delta$=$\delta$$\_$max/(the longest path) resulting in the minimum time search. The GM of elliptic workspace (EWS) requires calculation of interference in circumferential direction only. The procedure for GM includes categorization of obstacles to .educe necessary calculation. A GM based on rectangular workspace (RWS) using Cartesian coordinate is also considered to show yet another possible GM. The transformations of PS among Circular Workspace Geometry Mapping (CWS GM) , Elliptic Workspace Geometry Mapping (EWS GM) , and Rectangular Workspace Geometry Mapping (RWS GM), are also considered. The simulations for the EWS GM on various computer systems are carried out to measure performance of algorithm and the results are presented.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.7
• /
• pp.32-45
• /
• 1995

In this paper, we present a new method to tool path planning problem for rough cut of pocket milling operations. The key idea is to formulate the tool path problem into a TSP (Travelling Salesman Problem) so that the powerful neural network approach can be effectively applied. Specifically, our method is composed of three procedures: a) discretization of the pocket area into a finite number of tool points, b) neural network approach (called SOM-Self Organizing Map) for path finding, and c) postprocessing for path smoothing and feedrate adjustment. By the neural network procedure, an efficient tool path (in the sense of path length and tool retraction) can be robustly obtained for any arbitrary shaped pockets with many islands. In the postprocessing, a) the detailed shape of the path is fine tuned by eliminating sharp corners of the path segments, and b) any cross-overs between the path segments and islands. With the determined tool path, the feedrate adjustment is finally performed for legitimate motion without requiring excessive cutting forces. The validity and powerfulness of the algorithm is demonstrated through various computer simulations and real machining.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.8
• /
• pp.147-154
• /
• 2002

In this paper, a path navigation algorithm through use of a sensor platform is proposed. The sensor platform is composed of two electric motors which make panning and tilting motions. An algorithm for computing a real path and an obstacle length is developed by using a scanning method that controls rotation of the sensors on the platform. An Autonomous Robot Vehicle(ARV) can perceive the given path by adapting this algorithm. A sensor scanning method is applied to the sensor platform for using small numbers of sensor. The path navigation algorithm is composed of two parts. One is to perceive a path pattern, the other is used to avoid an obstacle. An optimal controller is designed for tracking the reference path which is generated by perceiving the path pattern. The ARV is operated using the optimal controller and the path navigation algorithm. Based on the results of actual experiments, this algorithm for an ARV proved sufficient for path navigation by small number of sensors and for a low cost controller by using the sensor platform with a scanning method.