• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.477-482
• /
• 2002

This research is concerned with the study of an active vibration absorber using piezoelectric actuators and Isolation pad. The active isolation system consists of 4-pairs of PZT actuators bonded on the surface of an aluminum plate and a passive damping material. The active system is connected to the passive system in series. The Signals of the accelerometers are fed into the PZT actuator through the controller. We proposed a new control technique which can deal with the shock as well as the base excitation in this study. The Positive Acceleration Feedback(PAE) tuned to the natural frequency of the vibration isolation system is used to suppress the vibrations caused by the shock using the top accelerometer signal. The Negative Acceleration Feedback (NAF) based on the base acceleration signal is used to counteract the base motion. Experimental results show that the proposed active vibration isolation system can suppress vibrations.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 1999년도 추계 학술발표회 논문집
• /
• pp.149-154
• /
• 1999

This paper describes a passive safety injection system with free piston Stirling pump working withabundant decay heat in the nuclear reactor during the hypothetical accident. The water column in the tube assembly connected from the hot chamber to the cold chamber in the pump oscillates periodically due to thermal volume changes of non-condensable gas in each chamber. The oscillating pressure in the water column is converted into the pumping power with a suction-and-bleed type valve assembly. In this paper a dynamic model describing the frequency of oscillation and pumping pressure is developed. It was found that the pumping pressure is a function of the temperature difference between the chambers. Also, the frequency oscillation depends on the length of the tube with water column.

• Wind and Structures
• /
• 제5권5호
• /
• pp.407-422
• /
• 2002

Passive control of the flutter condition of suspension bridges using a combined vertical and torsional tuned mass damper (TMD) system is presented. The proposed TMD system has two degrees of freedom, which are tuned close to the frequencies corresponding to vertical and torsional symmetric modes of the bridge which get coupled during flutter. The bridge-TMD system is analyzed for finding critical wind speed for flutter using a finite element approach. Thomas Suspension Bridge is analyzed as an illustrative example. The effectiveness of the TMD system in increasing the critical flutter speed of the bridge is investigated through a parametric study. The results of the parametric study led to the optimization of some important parameters such as mass ratio, TMD damping ratio, tuning frequency, and number of TMD systems which provide maximum critical flutter wind speed of the suspension bridge.

• Journal of Power Electronics
• /
• 제13권6호
• /
• pp.1058-1069
• /
• 2013

This paper proposes and designs a new output filter called an LCFL filter for application to three phase three wire shunt active power filters (SAPF). This LCFL filter is derived from a traditional LCL filter by replacing its capacitor with a C-type filter, and then constructing an L-C-type Filter-L (LCFL) topology. The LCFL filter can provide better switching ripple attenuation capability than traditional passive damped LCL filters. The LC branch series resonant frequency of the LCFL filter is set at the switching frequency, which can bypass most of the switching harmonic current generated by a SAPF converter. As a result, the power losses in the damping resistor of the LCFL filter can be reduced when compared to traditional passive damped LCL filters. The principle and parameter design of the LCFL filter are presented in this paper, as well as a comparison to traditional passive damped LCL filters. Simulation and experimental results are presented to validate the theoretical analyses and effectiveness of the LCFL filter.

• 한국정밀공학회지
• /
• 제21권11호
• /
• pp.209-218
• /
• 2004

The purpose of this paper is to suggest a practical and simple method for the identification of the joint mechanical properties and to apply it to human knee joints. The passive moment at a joint was modeled by three mechanical parts, that is, a gravity term, a linear damper term and a nonlinear spring term. Passive pendulum tests were performed in 5 fat and 5 thin men. The data of pendulum test were used to identify the mechanical properties of joints through sequential quadratic programming (SQP) with random initial values. The identification was successful where the normalized root-mean-squared (RMS) errors between the simulated and experimental joint angle trajectories were less than 10％. The parameter values of mechanical properties obtained in this study agreed with literature. The inertia, gravity and the damping constant were greater at fat men, which indicates more resistance to body movement and more energy consumption fer fat men. The suggested method is noninvasive and requires simple setup and short measurement time. It is expected to be useful in the evaluation of joint pathologies.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 가을 학술발표회 논문집
• /
• pp.362-369
• /
• 2002

This paper mainly propose the new passive vibration control device, named BRV(the bridge reduced vibration), for reducing excessive traffic-induced vibration of bridges and for measuring performance of BRV numerical example was simulated. The purpose of BRV is mainly on reducing vertical acceleration and displacement of bridge. In BRV we can control the stiffness and damping coefficient to accept the performance we want. The result of simulation showed that the vertical acceleration and displacement was effectively diminished. It would be concluded that BRV can be used to improve the serviceability of bridge and fatigue life etc.

• East Asian mathematical journal
• /
• 제28권3호
• /
• pp.339-345
• /
• 2012

In this paper, we study uniform exponential stabilization of the vibrations of the Kirchho type wave equation with acoustic boundary in a bounded domain in $R^n$. To stabilize the system, we incorporate separately, the passive viscous damping in the model as like Gannesh C. Gorain [1]. Energy decay rate is obtained by the exponential stability of solutions by using multiplier technique.

• Smart Structures and Systems
• /
• 제23권5호
• /
• pp.449-466
• /
• 2019

Cable-stayed bridges are attractive due to their beauty, reducing material consumption, less harm to the environment and so on, in comparison with other kinds of bridges. As a massive structure with long period and low damping (0.3 to 2%) under many dynamic loads, these bridges are susceptible to fatigue, serviceability disorder, damage or even collapse. Tuned Mass Damper (TMD) is a suitable controlling system to reduce the vibrations and prevent the threats in such bridges. In this paper, Multi Tuned Mass Damper (MTMD) system is added to the Ahvaz cable stayed Bridge in Iran, to reduce its seismic vibrations. First, the bridge is modeled in SAP2000 followed with result verification. Dead and live loads and the moving loads have been assigned to the bridge. Then the finite element model is developed in OpenSees, with the goal of running a nonlinear time-history analysis. Three far-field and three near-field earthquake records are imposed to the model after scaling to the PGA of 0.25 g, 0.4 g, 0.55 g and 0.7 g. Two MTMD systems, passive and active, with the number of TMDs from 1 to 8, are placed in specific points of the main span of bridge, adding a total mass ratio of 1 to 10% to the bridge. The parameters of the TMDs are optimized using Genetic Algorithm (GA). Also, the optimum force for active control is achieved by Fuzzy Logic Control (FLC). The results showed that the maximum displacement of the center of the bridge main span reduced 33% and 48% respectively by adding passive and active MTMD systems. The RMS of displacement reduced 37% and 47%, the velocity 36% and 42% and also the base shear in pylons, 27% and 47%, respectively by adding passive and active systems, in the best cases.

• 한국산학기술학회논문지
• /
• 제3권1호
• /
• pp.49-57
• /
• 2002

안전감쇠에 의해 전달 소음을 저감시키는 압전지능패널에 대한 실험적 연구를 수행하였다. 압전지능패널은 기본적으로 압전재료를 부착한 평판 구조물에 션트회로를 연결하고 흡음재들을 부가한 구조물이다. 지능패널은 중 주파수영역에서 흡음재의 수동적 특성을 이용하고 저주파수영역의 공진주파수에서는 압전감쇠를 적용하여 소음저감을 이루는 개념이다. 저주파공진에서의 소음저감을 위하여 측정한 전기적임피던스모델을 이용하는 압선감쇠를 적용하였다. 압전감쇠를 위한 공진 션트회로는 직렬로 연결된 저항과 인넉터로 구성되었으며, 저항과 인덕터는 회로에서 소산되는 에너지가 최대가 될 수 있는 값으로 최적설계하였다. 압전지능패널의 전달 소음저감성능은 음향터널을 사용하여 실험을 수행하였다. 음향터널은 사각단면 형태이며 소음 원으로 터널의 한 쪽 끝에 스피커가 설치되었다. 패널들을 터널의 중앙에 설치하여 투과 음압을 측정하였다. 흡음재를 갖는 지능패널과 흡음재와 공기층을 갖는 압전이중지능패널은 수동적 특성에 의해 저주파영역의 공진주파수를 제외한 중 주파수영역에서 뚜렷한 소음저감 효과를 나타내었다. 압전감쇠를 통하여, 첫 번째 공진주파수에서 약 10dB, 8dB의 소음저감 효과를 얻었다. 압전감쇠와 수동특성을 혼용하는 압전지능패널은 넓은 주파수영역에서의 소음저감을 위한 유망한 기술이다.

• 한국항공운항학회지
• /
• 제9권1호
• /
• pp.59-69
• /
• 2001

복합재로 된 회전날개깃을 상자보로 모델링하고 수동/능동 감쇠를 주기 위해 ACL(Active Constrained Damping Layer)을 상하양면에 부착하고 복합변위이론에 기초한 유한요소방법을 이용하여 구조해석을 수행하였다. 이 이론은 ACL내의 복합재와 점탄성층 그리고 압전층의 전단변형효과를 정확하게 모델링하는데 효과적이다. Hankel 의 특이값을 이용해 축차모델을 유도하였으며 축차모델과 측정된 출력에 기초한 LQG 제어기를 설계하였다. 그러나 LQG 제어기는 공칭 운전속도에서는 좋은 성능을 보여주었으나 운전속도가 변하는 상황에 대해서는 강인안정성을 보여주지 못했다. 이 LQG제어기의 강인안정성을 개선하기 위하여 루프전달회복을 통한 강인한 제어기를 설계하였다. 수치 예를 통해 제시된 제어기가 회전날개깃의 공기역학적인 안정성을 개선하는데 효과적이며 동체모드와 연계된 리드-래그 모드감쇠를 증가시켜 회전날개깃의 진동을 효과적으로 억제하는 것을 보였다.