• Journal of Korean Society for Atmospheric Environment
• /
• v.31 no.5
• /
• pp.461-471
• /
• 2015

Base on emission factors derived from National Institute of Environmental Research, Particulate matter from combined cycle power plants (CCPPs) has been estimated to be a important source of $PM_{10}$. Generally there is no serious emission of particulate matter in CCPPs. because the fuel of them is natural gas. But emission gas after long shut down season has very high dust content. Therefore $PM_{10}$ emission rate is dependent on its operation mode. In this study, particulate dispersion study for new city near CCPPs complex has performed using CALPUFF model for three case. $PM_{10}$ concentration has big difference between normal operation and 2 case start-up condition after long shutdown. In normal operating conditions, daily $0.32{\sim}0.50{\mu}g/m^3$ influence on of the surrounding area. But when 1~2 aerobic high concentration discharged conditions, average concentration is higher about $9.2{\sim}34.1{\mu}g/m^3$ than normal operating conditions.

• Environmental Engineering Research
• /
• v.23 no.2
• /
• pp.143-149
• /
• 2018

Air quality conditions and pollution status have been evaluated in the industrial area between Sharjah and Ajman border in UAE. Daily concentrations of $O_3$, CO, $NO_2$, $SO_2$, $PM_{2.5}$, $PM_{10}$, Total Volatile Organic Compounds (TVOC) and Total Suspended Particulate (TSP) have been monitored from Sept. 2015 to April 2016. The monthly average concentrations of $O_3$, CO, $NO_2$, $SO_2$, TVOC were within the UAE ambient air quality standards during the survey period. However, $PM_{10}$ and TSP levels exceeded the recommended limits in Sept. 2015, Oct. 2015 and March 2016. Temporal variations in air quality parameters showed highest levels in March 2016 for $PM_{2.5}$, $PM_{10}$, $NO_2$, TVOC and TSP, whereas $O_3$, $SO_2$ and CO showed relatively low values in this month. $PM_{2.5}$ levels in ambient air were above the EPA guideline of $35{\mu}g/m^3$ in all months. $PM_{2.5}$ was the critical ambient air pollutant with Index for Pollutant ($I_p$) values varying from 103-209, indicating Air Quality Index categories of unhealthy for sensitive groups (62.5%) to unhealthy (25%) to very unhealthy (12.5%). The $I_p$ average values of $PM_{2.5}$ decreased from Sept. 2015 to reach lowest value in Dec. 2015 before increasing gradually, peaking in March 2016. These results suggest the potential health risks associated with $PM_{2.5}$ is low in winter, where the prevailing meteorological conditions of lower temperatures, higher humidity, higher wind speed reduced particulate matter. The results revealed the industrial area is impacted by anthropogenic and natural sources of particulate matter.

• Journal of Environmental Health Sciences
• /
• v.45 no.1
• /
• pp.30-41
• /
• 2019

Objectives: The effects of particulate matter and ozone on health are being reported in a number of studies. These effects are likely to be stronger on the elderly population, but studies in this regard are scarce. The purpose of this study was to examine the effects of particulate matter ${\leq}2.5{\mu}m$ and ozone on the acute health status of the elderly population. Methods: In order to analyze the health status of the elderly population, the NHIS-Senior Cohort data was used. In this study of people 60 years or older in Seoul, the number of outpatient visits and ER visits between 2002 and 2013 were calculated. Each disorder and the lag effect were analyzed separately. Particulate matter and ozone were analyzed using both the single exposure model and the adjusted multi-exposure model. Results: In the single exposure analysis with PM2.5 as the exposure variable, with each increase of $10{\mu}g/m^3$, the number of outpatient visits increased by 1.0081 times, vascular disease 1.0065 times, chronic pulmonary disease 1.0086 times, and diabetes 1.0055 times. In the multi-exposure model adjusting for ozone, the number of outpatient visits increased by 1.0066 times. There was a one-day lag effect and 1.0066 times increase between PM2.5 and ER visits in the multi-exposure model and 1.0057 times when adjusted for ozone (p value <0.10). There was a one-day lag effect in all multi-exposure models with ozone as the main variable, and when the particulate matter was adjusted, there was a one-day delay and 1.0143 times increase in ER visits. Conclusions: In our study, an increase in the number of outpatient and ER visits in the elderly population in accordance with the increase in PM2.5 and ozone was found. The association found in our study could also produce a socioeconomic burden. Future studies need to be performed in regards to younger populations and other air pollutants.

• Journal of Korean Society for Atmospheric Environment
• /
• v.34 no.5
• /
• pp.651-658
• /
• 2018

Particulate matter (PM) emitted from fossil fuel-combustion facilities can be classified as either filterable or condensable PM. The U.S. Environmental Protection Agency (EPA) defined condensable PM as material that is in the phase of vapor at the stack temperature of the sampling location which condenses, reacts upon cooling and dilution in the ambient air to form solid or liquid in a few second after the discharge from the stack. Condensable PM passed through the filter media and it is typically ignored. But condensable PM was defined as a component of primary PM. This study investigates the change of condensable PM according to the variation in the sulfur dioxide of combustion gas. Domestic oil boilers were used as the source of emission ($SO_2$) and the level of $SO_2$ concentration (0, 50, 80, and 120 ppm) was adjusted by diluting general light oil and marine gas oil (MGO) that contains sulfur less than 0.5%. Condensable PM was measured as 2.72, 6.10, 8.38, and $13.34mg/m^3$ when $SO_2$ concentration in combustion gas were 0, 50, 80, and 120 ppm respectively. The condensable PM tended to increase as the concentration of $SO_2$ increased. Some of the gaseous air pollutants emitted from the stack should be considered precursors of condensable PM. The gas phase pollutants which converted into condensable PM should reduced for condensable PM control.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.26 no.1
• /
• pp.30-37
• /
• 2016

Objectives: This study was performed to measure and evaluate the concentration, size distribution and fugitive emission of particulate matter from process operations at foundries. Methods: Particle matter was collected from three foundries, and samples were also collected from a background site for calculating the fugitive emission concentration of the foundries. For the collection of the samples, a Nanosampler cascade impactor was used. Results: The concentration of TSP in the samples collected from the three foundries was $0.675{\sim}1.222mg/m^3$, $PM_{10}$ was $0.525{\sim}1.018mg/m^3$ and $PM_{2.5}$ was $0.192{\sim}0.615mg/m^3$. The mass size distribution was bimodal or monomodal with maximum peak at two stage(size $2.5{\sim}10{\mu}m$). The mass median aerodynamic diameter(MMAD) was $1.80{\sim}3.98{\mu}m$. The fugitive emission concentration of TSP varies in the range of 0.65 to $1.21mg/m^3$, which exceeds the emission standard of fugitive dust($0.5mg/m^3$). Conclusions: Particle concentration and size is an important industrial hygiene factor to protect foundry workers. Furthermore, the presence of high emission of particulate pollutants has a significant negative impact on the ambient air of the study area. Therefore, it is important to improve both the process and prevention facility in oder to reduce particulate pollutants in foundries.

• Elastomers and Composites
• /
• v.58 no.4
• /
• pp.161-172
• /
• 2023

Because particulate matter has emerged as a major contributor to air pollution, the tire industry has conducted studies to reduce particulate matters from tires by improving tire performance. In this study, we compared the conventional blending method, in which rubber, filler, and additives are mixed simultaneously, to the Y-blending method, in which masterbatches are blended. We manufactured carbon black (CB)-filled natural rubber (NR)/butadiene rubber (BR) blend and silica-filled epoxidized NR/BR blend compounds to compare the effects of the two blending methods on the physical properties of the compounds and the amount of particulate matter generated. The Y-blending method provided uniform filler distribution in the heterogeneous rubber matrix, improved processability, and exhibited low rolling resistance. This method also improved physical properties owing to the excellent filler-rubber interaction. The results obtained from measuring the generation of particulate matter indicated that, the Y-blending method reduced PM_2.5 particulate matter generation from the CB-filled and silica-filled compounds by 38% and 60%, and that of PM₁₀ by 29% and 67%, respectively. This confirmed the excellence of the Y-blending method regarding the physical properties of truck bus radial tire tread compounds and reduced particulate matter generated.

• The Journal of Bigdata
• /
• v.9 no.1
• /
• pp.127-140
• /
• 2024

This study investigated the impact of vehicle grade operation restrictions in green transportation areas on the concentration of fine particulate matter (PM2.5) year by year. The results indicate that these restrictions positively affected the reduction of PM2.5 levels. The green transportation area policy reduced vehicle emissions and encouraged the use of public and eco-friendly transportation, thereby improving air quality. A notable outcome was the decrease in PM2.5 concentrations, which is expected to positively impact the health of residents in urban areas. The study considered various factors and variables related to the effectiveness of the vehicle grade operation restrictions policy. It was determined that there is a need to discuss the implementation methods of the policy, regional characteristics, and other environmental factors. These findings provide important implications for managing fine particulate matter and urban planning, suggesting that reference materials and ongoing research will be necessary considering future urban sustainability.

• Journal of Environmental Science International
• /
• v.1 no.2
• /
• pp.25-31
• /
• 1992

Authors Investigated the particulate size distribution in work environment of Banwol and Changwon industry complex. Size distributions of particles exposured to workers in welding and in grounding process were evaluated by personal cascade impactors. Personal air samplers with personal cascade impactor were attached to the workers. The mass median diameter measured in welding sites were 0.3 to 3.BUm and in grinding sites were 1.5 to 2.6htn. Respirable matter fractions were ranged 32.67 to 65.055. Respirable matter fractions were calculated from the sixte distribution data by the respirable particle mass of the ACGIH criteria. The study relating to characteristics of particle of other industries and particulate sixte distribution is more needed in the near future

• Proceedings of the PSK Conference
• /
• 2003.04a
• /
• pp.165.2-166
• /
• 2003

Diesel exhaust is suspected to cause acute and chronic adverse effects on health. In recent. the effect of estrogenic endocrine disruptor in diesel particulate matter was little studied. Therefore, we examined the estrogenic activity of respirable diesel exhaust particulate matter derived from diesel engine motor. PM2.5 diesel exhaust of vehicle was collected using a high volume samples equipped with a cascade impactor. (omitted)

• Journal of Environmental Health Sciences
• /
• v.47 no.3
• /
• pp.259-266
• /
• 2021

Objectives: This study was conducted to identify the emissions characteristics of total particulate matter (TPM), fine dust (PM₁₀, PM_2.5), and gaseous pollutants (SOx, NOx) in iron and steel manufacturing facilities in order to investigate emissions factors suitable for domestic conditions. Methods: Total particulate matter (TPM), fine dust (PM₁₀, PM_2.5), and gas phase materials were investigated at the outlet of electric arc furnace facilities using a cyclone sampling machine and a gas analyzer. Results: The concentrations of TPM ranged from 1.64 to 3.14 mg/Sm³ and the average was 2.47 mg/Sm³. Particulate matter 10 (PM₁₀) averaged 1.49 mg/Sm³ with a range of 0.92 to 1.99 mg/Sm³, and the resulting ratio of PM₁₀ to TPM was around 60 percent. PM_2.5/PM₁₀ ranged from 33.7 to 47.9% and averaged 41.6%. Sulfur oxides (SOx) were not detected, and nitrogen oxides (NOx) averaged 6.8 ppm in the range of 5.50 to 8.67 ppm. TPM emission coefficients per product output were in the range of 0.60 to 1.26 g/kg, 0.13 to 0.79 g/kg for PM₁₀ and 0.12 to 0.36 g/kg for PM_2.5, and showed many differences from the emissions coefficients previously announced. An emissions coefficient for NOx is not currently included in the domestic notices, but the results were calculated to be 0.42 g/kg per product output. Conclusions: Investigation and research on emissions coefficients that can reflect the characteristics of various facilities in Korea should be conducted continuously, and the determination and application of unique emissions coefficients that are more suitable for domestic conditions are needed.