• Bulletin of the Korean Chemical Society
• /
• 제27권9호
• /
• pp.1423-1428
• /
• 2006

In this study, we have prepared pitch binded AC (activated carbon)/$AC/TiO_2$ composites photocatalysts through carbon tetrachloride solvent method. The developed samples were characterized with surface properties, structural crystallinity between AC and $AC/TiO_2$, elemental identification and photocatalytic activity. The results of the textural surface properties demonstrate that there are slight increases in the BET surface area and adsorbed volume from adsorption isotherm of composite samples with increasing of the amount of AC. The SEM results present to the characterization of porous texture on the pitch/AC/$AC/TiO_2$ composites and homogenous compositions in the particle for all the materials used. From XRD data, a weak and broad carbon peak of graphene remained rutile peaks kept with anatase structure were observed in the X-ray diffraction patterns for the pitch/AC/$AC/TiO_2$ composites. The EDX spectra show the presence of C, O and S with strong Ti peaks. Most of these samples are richer in carbon and major Ti metal than any other elements. Finally, the excellent photocatalytic activity of the pitch/AC/$AC/TiO_2$ composites between relative concentration ($c/c_o$) of MB and UV irradiation time could be attributed to the both effects between photocatalysis of the supported $AC/TiO_2$ and adsorptivity of the two kinds of carbons.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.176-176
• /
• 2007

Flat-panel direct conversion detectors used in compound substance of semiconductor are being studied for digital x-ray imaging. Recently, such detectors are deposited by physical vapor deposition(PVD) generally. But, most of materials (HgI2, PbI2, TlBr, PbO) deposited by PVD have shown difficult fabrication and instability for large area x-ray imaging. Consequently, in this paper, we propose applicable potentialities for screen printing method that is coated on a substrate easily. It is compared to electrical properties among semiconductors such as $HgI_2$, $PbI_2$, PbO, HgBrI, InI, and $TlPbI_3$ under investigation for direct conversion detectors. Each film detector consists of an ~25 to $35\;{\mu}m$ thick layer of semiconductor and was coated onto the substrate. Substrates of $2cm{\times}2cm$ have been used to evaluate performance of semiconductor radiation detectors. Dark current, sensitivity and physics properties were measured. Leakage current of $HgI_2$ as low as $9pA/mm^2$ at the operation bias voltage of ${\sim}1V/{\mu}m$ was observed. Such a value is not better than PVD process, but it is easy to be fabricated in high quality for large area x-ray Imaging. Our future efforts will concentrate on optimization of growth of film thickness that is coated onto a-Si TFT array.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.388-389
• /
• 2005

In this paper, the electric properties of mercury Iodide multi-layer samples has been investigated. We measured and analyzed their performance parameters such as the X-ray sensitivity and dark-current for a mercury Iodide multi-layer X-ray detector with a dielectric layer. The digital X-ray image detector can be constructed by integrating photoconduction multi-layer that dielectric layer has characteristics of low dark-current, high X-ray sensitivity. However this process has found to have complexity on the performance of the sample. We have investigate dielectric layer that it substitute dielectric layer for HgO(Mercury Oxide). We have employed two approaches for producing the mercury Iodide sample : 1) Physical Vapor Deposition(PVD) and 2) Particle-In-Binder(PIB). In this paper fabricated by PIB Method with thicknesses ranging from approximately 180um to 240um and we could produce high-quality samples for each technique particular application. As results, the dielectric materials such as HgO between the dielectric layer and the top electrode may reduce the dark-current of the samples. Mercury Iodide multi-layer having HgO has characteristics of low dark-current, high X-ray sensitivity and simple processing. So we can acquired a enhanced signal to noise ratio. In this paper offer the method can reduce the dark-current in the X-ray detector.

• 유기물자원화
• /
• 제29권4호
• /
• pp.47-54
• /
• 2021

본 연구는 수소 경제 사회에서 누출·농축 수소에 대한 안전성 확보를 위해 Pd/TiO₂ 촉매를 허니컴 형태로 코팅하여 그 성능을 평가하였다. 열원에 노출되지 않는 액상환원법을 기반으로 촉매를 제조하였으며, 2~4 nm의 매우 작은 활성입자로 존재함을 H₂-chemisorption 분석을 통해 확인하였다. 또한 환원반응온도가 증가할수록 metal dispersion 감소 및 활성입자 크기가 증가함을 확인하였으며, 활성금속 입자 크기와 수소 산화 성능은 비례관계에 있음에 따라 수소 산화 성능 감소결과와 일치함을 확인하였다. 제조된 촉매를 실 공정에 적용할 수 있도록 허니컴 형태의 지지체에 코팅하였을 때, AS-40 바인더를 20 wt%이상 코팅하였을 때 저농도 수소 조건에서 90% 이상의 산화 성능을 관찰하였다. 이는 촉매의 부착강도를 증진시키고 촉매 탈리를 방지하여 장기적인 촉매 활성을 기대할 수 있음을 SEM 분석을 통해 확인하였다. 본 연구를 통해 가스화 등과 같은 유기물 자원화를 통해 수소 생산 및 수소 인프라 구축 사회에서 안전성을 확보할 수 있는 기초연구로, 추후 예측하지 못한 안전사고를 대응할 수 있는 시스템으로써 활용될 수 있을 것으로 판단된다.

• 한국전기전자재료학회논문지
• /
• 제24권4호
• /
• pp.297-302
• /
• 2011

Recently, low temperature co-fired ceramic (LTCC) technology is widely used in sensors, actuators and microsystems fields because of its very good electrical and mechanical properties, high reliability and stability as well as possibility of making 3D micro structures. In this study, we investigated the effects of sputtering gas ratio and annealing temperature on the crystal structure of $Pb(ZrTi)O_3$ (PZT) thin films deposited on LTCC substrate. The LTCC substrate with thickness of $400\;{\mu}m$ were fabricated by laminating 4 green tapes which consist of alumina and glass particle in an organic binder. The PZT thin films were deposited on Pt / Ti / LTCC substrates by RF magnetron sputtering method. The results showed that the crystallization of the films were enhanced as increasing $O_2$ mixing ratio. At about 25% $O_2$ mixing ratio, was well crystallized in the perovskite structure. PZT thin films was annealed at various temperatures. When the annealing temperature is lower, the PZT thin films become a phyrochlore phase. However, when the annealing temperature is higher than $600^{\circ}C$, the PZT thin films become a perovskite phase. At the annealing temperature of $700^{\circ}C$, perovskite PZT thin films with good quality structure was obtained.

• 한국건축시공학회지
• /
• 제18권3호
• /
• pp.211-218
• /
• 2018

이 연구에서는 국내산 인공 경량골재를 사용한 콘크리트의 실험결과를 바탕으로 콘크리트 표준시방서의 관련내용에 대한 합리성 및 개정의 필요성을 평가하였다. 국내 표준시방서의 내용은 ACI 211.2, ACI 213, ACI 301, JASS 5 및 CEB-FIP 시방내용들과 비교하였다. 국내산 인공 경량 잔골재의 연속적 입도분포를 위해서는 최대직경 2.5mm 이하의 천연모래 혼입이 요구되었다. 경량골재 콘크리트의 재료분리 및 과도한 블리딩을 제어하기 위해서는 현재 시방서에서 제시된 최대 물-결합재비와 단위수량에 대한 수정이 요구되었다. 특히, 배합 목표성능인 초기 슬럼프, 28일 압축강도, 공기량 및 기건 단위용적중량에 대해 경량골재 콘크리트의 합리적인 배합설계 절차의 확립이 요구되었다. 결과적으로 콘크리트 표준시방서는 국내산 인공 경량골재의 특성을 고려하여 전반적이 개정이 요구되었다.

• 자원리싸이클링
• /
• 제24권3호
• /
• pp.34-43
• /
• 2015

철강 산업에서의 원재료는 생산성, 품질, 가격경쟁력에 결정적인 역할을 하고 있다. 철강제품의 원재료를 함철부산물로 활용한다면, 함철부산물을 처리하기 위한 비용 및 환경오염문제를 해결할 뿐만 아니라 가격경쟁력을 높일 수 있다. 함철부산물들은 대부분 작읍입도를 가지고 있어서, 제강공정 내에 직접 투입하게 되면 열 유동 및 원료 비산 등의 문제가 발생하게 된다. 이러한 문제점을 해결하고 추가적인 환원을 유도하기 위해 철원에 탄재를 혼합한 뒤 단괴를 성형하여 제강공정 내에 투입하는 방법이 연구되고 있다. 본 연구에서는 함철부산물에 탄재를 혼합하여 단괴를 성형하는 방법에 대해 연구하였다. 함철부산물, 탄재, 융제, 바인더에 따른 CCBI (carbon composite briquette iron)의 성형성 및 압축강도를 확인하였다.

• 콘크리트학회논문집
• /
• 제25권3호
• /
• pp.305-312
• /
• 2013

이 연구는 물-결합재(W/B) 비에 따른 실리카 퓸이 알칼리 활성화 슬래그 시멘트(AASC)에 미치는 유동성과 강도 특성에 대한 연구이다. W/B비는 0.50에서 0.60까지 0.05 단위로 일정하게 변화시켰다. 실리카 퓸은 고로슬래그 중량의 0%에서 50%까지 치환시켰다. 활성화제는 수산화나트륨(NaOH)를 사용하였고, 농도는 3M로 하였다. W/B 비에 따른 강도는 1, 3, 7 그리고 28일을 측정하였다. 유동성 측정 결과는 실리카 퓸의 치환율이 증가할수록 감소하였다. 압축강도는 실리카 퓸의 치환율이 증가할수록 증가하였다. 또한 W/B 비가 증가할수록 모든 재령에서 강도는 감소하였다. 실리카 퓸은 W/B 비와 실리카 퓸의 치환율에 따라서 활성화 반응을 증대시켜 강도를 증가시키는 것을 알 수 있었다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2010년도 춘계학술발표대회
• /
• pp.19.2-19.2
• /
• 2010

Printed electronics using printing process has broadened in all respects such as electrics (lighting, batteries, solar cells etc) as well as electronics (OLED, LCD, E-paper, transistor etc). Copper is considered to be a promising alternative to silver for printed electronics, due to very high conductivity at a low price. However, Copper is easily oxidized, and its oxide is non-conductive. This is the highest hurdle for making copper inks, since the heat and humidity that occurs during ink making and printing simply accelerates the oxidation process. A variety of chemical treatments including organic capping agents and metallic coating have been used to slow this oxidation. We have established synthetic conditions of copper nanoparticles (CuNPs) which are resistant to oxidation and average diameter of 20 to 50nm. Specific resistivity should be less than $4\;{\mu}{\Omega}{\cdot}cm$ when sintered at lower temperature than $250^{\circ}C$ to be able to apply to conductive patterns of FPCBs using ink-jet printing. Through this study, the parameters to control average diameter of CuNPs were found to be the introduction of additive agent, the feeding rate of reducing agent, and reaction temperature. The CuNPs with various average diameters (58, 40, 26, 20nm) could be synthesized by controlling these parameters. The dispersed solution of CuNPs with an average size of 20 nm was made with nonpolar solvent containing 3 wt% of binder, and then coated onto glass substrate. After sintering the coated substrates at $250^{\circ}C$ for 30 minutes in nitrogen atmosphere, metallic copper film resulted in a specific resistivity of $4.2\;{\mu}{\Omega}{\cdot}cm$.

• 한국표면공학회지
• /
• 제40권1호
• /
• pp.23-31
• /
• 2007

The objective of this study is to investigate the effect of Al addition on the reaction behavior of cobalt with molten zinc. Pure cobalt specimen was immersion tested in the three kinds of molten zinc (pure, 0.12%Al added and 0.24%Al added) baths at $460^{\circ}C,\;490^{\circ}C\;and\;520^{\circ}C$. For the understanding of degradation processes, specimens were analyzed with scanning electron microscope (SEM) and energy dispersive spectrum (EDS), and electrochemical stripping method. When 0.12% and 0.24% Al was added in molten zinc baths, three intermetallic compounds layers of ${\gamma},\;{\gamma}_1,\;and\;{\gamma}_2$ were formed on the Co matrix and ${\beta}_1$ layer was not formed between the Co matrix and the ${\gamma}$ layer. Particles of CoAl intermetallic compound were formed at the interface between the ${\gamma}_2$ layer and zinc melt and they did not adhere to the Co-Zn intermetallic layer. Weight loss of the Co specimen increased as Al content in the molten zinc increased and the relationship of weight loss vs. immersion time followed parabolic rate law. Rate controlling process for the reaction rate of Co with Al added molten zinc was analyzed as the diffusion process of Al atom through a boundary layer between the ${\gamma}_2$ layer and the Al added zinc melt.