• 한국추진공학회지
• /
• 제20권1호
• /
• pp.14-19
• /
• 2016

HTPB/AP계 혼합형 고체 추진제의 점도와 기계적 특성은 산화제인 AP의 입자 크기에 크게 영향을 받는다. $190{\mu}m$의 크기의 AP와 $7{\mu}m$ 크기의 AP를 사용한 HTPB/AP 추진제에서 큰 입자/작은 입자의 비율이 70/30~60/40 범위인 조성의 추진제가 매우 낮은 점도를 나타났는데, 이것은 고체입자의 충전율이 높은 상태이기 때문이다. 추진제의 인장강도 시험에서 Toughness는 큰 입자의 함량이 많아질수록 증가하는 것으로 나타났다. 낮은 점도와 좋은 인장강도를 동시에 고려할 때, AP 큰 입자와 작은 입자를 70/30으로 사용하는 것이 가장 효과적인 것으로 분석되었다.

• 한국세라믹학회지
• /
• 제45권8호
• /
• pp.486-492
• /
• 2008

Reaction bonded silicon carbide(RBSC) composite for heat-exchanger was fabricated by molten Si infiltration method. The raw materials with variable particle sizes were used in this experience. The finer the particle size in sintered silicon carbide was the more increasing 3-point bending strength and fracture toughness. As the adaptable particle sizes had been occupied interstice arising from packing sample, the mechanical properties were increased. In the PCS1-1 sample, the 3-point bending strength and fracture toughness were 323MPa and $4.9\;MPa{\cdot}m^{1/2}$, respectively.

• 상하수도학회지
• /
• 제27권2호
• /
• pp.241-249
• /
• 2013

Ethanolamine (ETA) is widely used for alkalinization of water in steam cycles of nuclear power plants with pressurized water reactor. When ETA contained wastewater was released, it could increase COD and T-N. The treatment of the COD and T-N from ETA wastewater was investigated using the GAC as particle electrodes in three-dimensional electrode reactor (TDE). This study evaluated the effectiveness of GAC as particle electrode using different packing ratio at 300 V. The results showed that GAC-TDE could reduce ETA much more efficiently than ZVI-TDE at the mass ratio of GAC to insulator, 1:2. Additionally, The effect of applied electric potential to COD and T-N reduction was investigated. The results showed the high COD, T-N reduction and current efficiency at the low electric potential. Using the GAC-TDE will provide a better ETA reduction with reducing electrical potential dissipation.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제12C권4호
• /
• pp.229-235
• /
• 2002

The apparent volume resistivity of powders measured by both the tapping and the compressing methods was compared in this study. Factors such as applied voltage, pressure, corona charging, and so on affecting the apparent volume resistivity of polymer powders were also examined experimentally. Powders of polyacrylonitrile and Nylon 11 were mainly used. The values of the apparent resistivity of polymer powders taken by the tapping method turned out to be larger than those taken by the compressing method, which indicates that the apparent volume resistivity of polymer powders depends strongly on the measurement method. The apparent resistivity of polymer powders increased with an increase in applied voltage while it decreased with an increase in pressure, tapping time, and particle size. The influence of the moisture content of powder and corona charging on the resistivity of polymer powders is also discussed.

• 한국환경보건학회지
• /
• 제35권4호
• /
• pp.295-303
• /
• 2009

A simulated wastewater containing the dye Rhodamine B (RhB) was electrolytically treated using a three-dimensional electrode reactor equipped with granular activated carbon (GAC) as particle electrode. The effect of type of packing material (GAC, ACF, Nonwoven fabric fiber coated with activated carbon), amounts of GAC packing (25-100 g), current (0.5-3 A) and electrolyte concentration (0.5-3 g/l) was evaluated. Experimental results showed that performance for RhB decolorization of the 3 three-dimensional electrodes lie in: GAC > Nonwoven fabric fiber > ACF. When considered RhB decolorization, oxidants concentration and electric power, optimum GAC dosage was 50 g. Generated concentration of 3 oxidants ($ClO_2$, free Cl, $H_2O_2$) was increased with increase of applied current, however optimum current for RhB degradation was 2.5 A. The oxidants concentration was increased with increase of NaCl concentration and optimum NaCl dosage for RhB degradation was 1.5 g/l.

• 한국가구학회지
• /
• 제14권1호
• /
• pp.1-9
• /
• 2003

This research was carried out for packing materials and building materials to examine thylene gas adsorption and effect of keeping fruit fresh of wet formed charcoal-fiber mposite made from defibrated fiber of Pinus densiflora Sieb. et Zucc. and white charcoal from uercus variabilis Bl.(wood fiber: charcoal=8:2, 6:4, 4:6, 2:8), with/without phenol formaldehyde resin(PF, Non volatile content:$52\%$, resin content $1,3,5\%$). The results are summarized as follows: 1. The higher the charcoal content, the more the ethylene gas adsorption. At the same mixing ratio of fiber to charcoal, $\#100-200$ of charcoal particle size gave the better reslts than $\#60-100$. 2. Adding PF into the charcoal fiber composite decreased the capacity of ethylene gas adsorption but there was no significant difference until $5\%$ adding amount of PF. 3. For keeping fruit fresh for a long time, Charcoal fiber composite was $66\%$ longer than control. The higher the white charcoal content, the longer fresh time.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.1105-1110
• /
• 2008

An experimental study was performed to control Ice Packing Factor (IPF) of ice slurry in a pipe in a real time. This paper presented the concept that IPF can be adjusted by the amount of the solution contained to ice slurry. Based on this concept, we designed IPF controller consisting of the outlet tube providing ice slurry and the upper tube discharging only a solution through holes, and investigated the technical validity and efficiency of the controller experimentally. As a result, the original proposed IPF controller could not control IPF of ice slurry in a pipe. This is because an ice of ice slurry was drained out into not only the outlet but also the upper of the controller due to the size of the holes relatively large compared to the ice particle. Therefore, we changed the hole size of IPF controller surface using fine meshes and then, observed that IPF in a pipe was increased by $4{\sim}7$ percent when the hole size was $80{\mu}m$ and less.

• 한국세라믹학회지
• /
• 제33권12호
• /
• pp.1414-1420
• /
• 1996

평균 입경 8${\mu}{\textrm}{m}$ Si 분말을 사용하여 무가압 분말 충전 성형볍에 의해 Si 성형체를 제조하였다. 이 Si 성형체를 1350,140$0^{\circ}C$의 온도에서 3~35시간동안 N2/H2 분위기에서 반응 소결한 후 미세구조를 관찰하였다. 반응 소결체는 90% 이상의 질화율과 88%의 상대밀도를 보였다. 반응 소결체의 가스압 소결을 위해 소결조제로서 MgO를 Mgnitrate 수용액 형태로 Si 성형체에 5wt% 첨가한 후140$0^{\circ}C$에서 15시간동안 반응 소결하였다. 이후 반응 소결체를 1800, 1900, 200$0^{\circ}C$에서 각각 150, 300분 동안 가스압 소결을 행하여 95%의 상대밀도와 598 MPa의 꺾임강도, 6 MPa.m1/2의 파괴인성을 나타내는 질화규소 소결체를 제조하였다.

• 공업화학
• /
• 제28권2호
• /
• pp.177-185
• /
• 2017

본 연구에서는 스테아르산(SA), 올레산(OA), 리놀레산(LA) 등의 지방산이 지질 소포체 막과의 상호 작용에 미치는 영향에 관하여 살펴보았다. 이를 위하여 지방산 종류 및 농도 변화에 따른 리포좀 평균 입자 크기 및 제타 전위, 리포좀 막의 deformability, fluorescence anisotropy ratio 등을 측정하고 TEM 관찰을 통하여 지방산 첨가가 리포좀 막의 유동성 변화에 미치는 역할에 관하여 살펴보았다. 기본적으로 SA, OA, LA 등의 지방산 첨가는 동일한 경향을 나타내었다. 즉, 지방산을 첨가함에 따라 리포좀이 보다 치밀한 패킹을 갖게 되어서 리포좀의 크기는 감소하고 제타 전위 값은 증가하였으나, 지방산의 과도한 첨가는 리포좀에서 다형(polymorphic) 구조를 가지는 지질 입자 응집체로의 전이를 일으켰다. SA, OA 및 LA 지방산 시스템에서의 최소 리포좀 크기와 가장 치밀한 리포좀 패킹은 레시틴 대비 지방산의 몰 비율이 각각 0.70, 0.50, 0.25인 조건에서 관찰되었으며, 리포좀 막의 deformability와 fluorescence anisotropy ratio 측정에 의한 리포좀 막의 유동성 측정 결과는 TEM 및 입자 크기 측정 결과와 일치함을 알 수 있었다.

• 한국세라믹학회지
• /
• 제34권1호
• /
• pp.95-101
• /
• 1997

평균입경이 22.1$\mu$m인 알루미늄 분말을 사용하여 무가압 분말 충전 성형법으로 52%의 상대밀도를 갖는 성형체를 제조하였다. 산화반응의 활성화 에너지는 TG의 무게 변화로부터 구하였으며, 16~64kJ/mol 범위의 값을 나타내었다. 활성화에너지의 변화와 미세구조의 관찰로부터 산화반응이 산화막의 파괴와 용출에 의존함을 확인하였다. 알루미늄 성형체를 1000~140$0^{\circ}C$에서 4~60시간동안 산화반응시켰을 때, 알루미늄의 산화반응이 시간보다 온도에 의존하였다. 140$0^{\circ}C$에서 60시간동안 산화반응시킨 시편의 산화율은 92%를 나타내었으며, 이 시편을 다시 1$600^{\circ}C$에서 15시간 소결시켰을 때, 소결체는 62%의 상대밀도를 나타내었다.