• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.843-847
• /
• 1999

In this research, C/SiC composites, i.e. activated carbon coated with SiC obtained from dichlorodimethylsilane(DDS) and hydrogen, have been made by chemical vapor infiltration(CVI) in a fluidized bed reactor. Activated carbons of sizes of 4~12, 12~20, and 20~40 mesh were used. After deposition the surface area, the amount and the shape of deposit of each sample were observed at different concentrations of reactant DDS, sizes of activated carbon, reaction pressures and reaction times. The experimental results showed that uniform deposition in the pores of sample was obtained at a lower concentration of DDS and a lower pressure. Additionally, from the observation that the pore diameter and the surface area have minimum values at a certain time of deposition, it was known that deposition occurred inside of the pore at first and then on the outside of particle. Small particles of SiC were deposited uniformly on the surface of activated carbon at lower DDS concentrations and lower reaction pressures. The results were confirmed by SEM, TGA, the pore size distribution analyzer and BET.

• The Korean Journal of Nuclear Medicine
• /
• v.24 no.2
• /
• pp.237-243
• /
• 1990

Pulmonary embolism demands rapid and accurate diagnosis. And ventilation imaging has greatly improved the diagnostic accuracy of pulmonary embolism in addition to perfusion imaging. Agents currently used include xenon-133, krypton-81m and technetium-99m radioaerosols. However radioactive gases are compromised by availability and cost for krypton-81m, radiation dose, gamma energy and non?physiologic behaviour for xenon-133. Radioaerosols of technetium-99m componds are rapidly cleared from the lung after inhalation, and their relative low effeciency (specific radioactivity) and wide distribution of particle sizes make them also suboptimum. A new ventilation agent, Technegas is a suspension of structured graphite ellipsoids with diameter below 20nm, labelled with $^{99m}Tc$ in a carrier gas of Argon. This report describes the authors' clinical experience with Technegas. This is the first reported clinical study of this agent in Korea. A comparison of Technegas and $^{99m}Tc-DTPA$ aerosol was performed in 12 patients with various pulmonary diseases such as COPD, pulmonary tuberculosis and pleural effusion. All patients were studied with $^{99m}Tc-DTPA$ aerosol inhalation and Technegas ventilation. In both studies image quality was assessed (1) semiquantitatively by scoring bronchial and gastric activity, (2) subjectively by direct visual comparison of peripheral lung images and (3) quantitatively by computing the peripheral penetration index(PI) for each lungs. The bronchial activites were seen in 7 out of 12 cases with $^{99m}Tc-DTPA$ aerosol and in 5/12 with Technegas. The gastric activities were seen in 5/12 and 1/12 cases respectively. The average values of PI were 61.26% with $^{99m}Tc-DTPA$ aerosol and 69.20% with Technegas (p>0.05). Using $^{99m}Tc-DTPA$ aerosol, COPD patients showed deposition in the central airways with poor visualization of the peripheral areas of the lungs. In Technegas studies these phenomena were less prominent, and the examination is well tolerated by pateients and requires only a minimum of patient cooperation. With superiority of easy availability and handling, better physical characteristics and favorable Image quality, Technegas is a Promising agent for lung ventilation scanning.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.1
• /
• pp.63-71
• /
• 2018

In this study, the torque and horizontal stress acting on vane were measured and then used to determine a friction angle of sand. A dry Nakdong River sand was prepared for loose and dense conditions in a cell and then pressurized with 25, 50, 75 or 100 kPa from the surface of sand. A vane (5cm in diameter and 10cm in height) was rotated and the torque and horizontal stress were measured at real time. A maximum torque was 3.5-9.5Nm for loose sand and 7.4-17.6Nm for dense sand, respectively. The maximum torque increased as an overburden pressure increased. The maximum torque obtained at 14-20 degrees of vane rotation, which was not influenced by the initial alignment of earth pressure and vane blade. An initial horizontal stress ratio was 0.33-0.35 on the average. The horizontal stress increased initially and then decreased due to particle disturbance. A friction angle was calculated from real time varying horizontal stress and torque, which decreased with increasing overburden pressure. The friction angle of loose sand from vane shear test was similar to that of direct shear test but that of dense sand was overestimated.

• Korean Journal of Materials Research
• /
• v.9 no.9
• /
• pp.872-877
• /
• 1999

The purpose of this research was to investigate the characteristics and the cleaning efficiency on HN(sub)4OH solutions added with H(sub)2O(sub)2 and surfactants. NH(sub)4OH solutions added with surfactants did not show much changes in pH and redox potential (Eh) as a function of NH(sub)4OH concentration compared with NH(sub)4OH solution. However H(sub)2O(sub)2 added NH\ulcornerOH solutions showed the decrease of pH and the increase of Eh as the concentration of NH(sub)4OH increased. The decrease of surface tension from 72 dynes/cm to 38 dynes/cm was observed in solutions added with surfactant but not in H(sub)2O(sub)2. The etch rates of silicon in NH(sub)4OH solutions(NH(sub)4OH:H(sub)2O= 1 : 5) showed at least 50 times higher than those in H(sub)2O(sub)2 and surfactant added NH(sub)4OH solutions(NH(sub)4OH:H(sub)2O(sub)2= 1 : 1 : 5) solution removed the PSL particles (0.67$\mu\textrm{m}$ in diameter) on Si wafers effectively at all temperatures investigated. NH(sub)4OH solution added with a surfactant could not remove particles at room temperature, however it was possible to remove particles at higher temperatures, 5$0^{\circ}C$ and 8$0^{\circ}C$.

• Korean Journal of Food Science and Technology
• /
• v.46 no.2
• /
• pp.135-142
• /
• 2014

Physicochemical, pasting, and digestion properties of sweet potato starches from 11 Korean cultivars were investigated. Starch granules were variably oval, round, polygonal, spherical, and bell-shaped, and of 10.2-15.3 ${\mu}m$ in mean particle diameter. Amylose contents varied from 12.3 to 17.4%. A similar chain length distribution of amylopectin was found in each of the cultivars. The portion of $B_3$ correlated with the degree of amylose leaching. Thermal properties determined by differential scanning calorimetry showed high values of gelatinization temperatures in Shinyulmi and Jeungmi starches, but a relatively low value in Daeyumi starch. All starches exhibited a Ca-type diffraction pattern. Differing patterns were observed in swelling factors, depending on temperature. The contents of rapidly digestible starch, slowly digestible starch, and resistant starch ranged from 9.6-17.4, 31.4-45.6, and 35.7-62.8%, respectively. In Rapid Visco Analyser profiles, differences were observed in pasting parameters such as pasting temperature, peak viscosity, final viscosity, and breakdown.

• Applied Chemistry for Engineering
• /
• v.16 no.4
• /
• pp.485-490
• /
• 2005

Effects of gas injectino on the copper recovery form industrial waste water in a fluidized-bed electrolytic reactor were investigated. Effects of gas injection on the individual phase holdup and efficiency of copper recovery for given operating variables such as liquid and gas velocity (0.1~0.4 cm/s), current density ($2.0{\sim}3.5A/dm^2$) and amount of fluidized solid particles (1.0~4.0 wt%) were examined. The solid particle, whose diameter and swelling density were 0.5 mm and $1100kg/m^3$, respectively, was made of polystylene and divinyl benzene. It was found that the holdup of gas and solid phases increased, but that of the liquid phase decreased with increasing velocity of gas injected into the reactor. With increasing gas and/or liquid velocity and increasing amount of fluidized particles is not needed, the rate of copper recovery increased to a maximum value of and subsequently decreased. The recovery rate of copper increased almost linearly with increasing current density in accordance with Faraday's law.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.5
• /
• pp.611-618
• /
• 2018

In this study, numerical analysis of solid-liquid two-phase flow was conducted as a preliminary step to analyze the flow characteristics of drilling fluid using the commercial CFD code, ANSYS CFX 14.5. The homogeneous model and separated flow model were used to simulate solid-liquid two-phase flow phenomena. In the separated flow model, Gidaspow's drag force model was applied with the kinetic theory model was applied for solid particles. The validity of the numerical model used in this study was verified based on the published experimental results. Numerical analysis was carried out for volume fractions of 0.1 to 0.5 and velocities of 1 to 5 m/s in a horizontal tube with a diameter of 54.9 mm and a length of 3 m. The Pressure drop and volume fraction distribution of solid particles were confirmed. The pressure drop was predicted using the homogeneous model and separated flow model within the MAE of 17.04 % and 8.98 %, respectively. A high volume fraction was observed in the lower part of the tube, and the volume fraction decreased toward the upper part. As velocity increased, variations in volume fraction distribution at varying heights were decreased, and the numerical results predicted these flow characteristics well.

• Food Science and Preservation
• /
• v.22 no.3
• /
• pp.385-391
• /
• 2015

This study was conducted to develop a spray-dried garlic chives (Allium tuberosum) powder and to evaluate its quality characteristics depending on the treatment of steam blanching pretreatment $100^{\circ}C$, 3 min) and the addition of forming agents (dextrin (DE=10), ${\beta}$-cyclodextrin) during process. The steam blanching pretreatment showed an increase in $L^*$ value while a decrease in $-a^*$, $b^*$, $C^*$, and $h^o$ values of the powder. Moisture content and water soluble index were not affected by the treatment of steam blanching and the addition of forming agents, whereas the particle diameter was the smallest in the steam blanching treatment and dextrin addition. Chlorophyll, phenolic compound, and vitamin C content, and DPPH radical scavenging activity of non-pretreated powder were significantly higher than those of the steam blanching treated powders. However, there was no significant difference between the two forming agents. The sensory acceptability (color, smell, and overall acceptability) of powder treated with steam blanching were significantly higher than those of non-pretreated powders. Therefore, the steam blanching pretreatment of fresh garlic chives affected on the better quality characteristics of the spray-dried powders when compared with non-pretreated powder though it adversely affected the natural chemical quality of fresh garlic chives.

• Korean Journal of Agricultural Science
• /
• v.22 no.2
• /
• pp.151-155
• /
• 1995

Two types of modified celluloses which contain trinitrophenyl groups as chromophore were synthesized from carboxymethyl cellulose Whatman CM 70 and CM 32. Diaminoethyl groups were added to the CM 70 and CM 32 to make DAE-CM celluloses and then the DAE-CM groups were substituted by 2,4,6-trinitrophenyl groups to produce TNP-celluloses. Average particle size of the TNP-cellulose from CM 32 was $44.6{\pm}9.6{\mu}m$ in diameter and $127.9{\pm}22.5{\mu}m$ in length, which was much smaller than those from CM 70, however its TNP-moiety per gram determined by using the molar extinction coefficient $1.33{\times}10^4$ of ${\varepsilon}$-TNP-lysine at 345 nm, was 0.68 millimoles, which was 5.6-fold greater than those from CM 70. The absorption spectrum of TNP-oligosaccharides which were the soluble products of TNP-celluloses by a cellulase preparation Onozuka R-10, showed a maximal peak at 344 nm. Increases in the absorbance during hydrolysis were linear with the enzyme concentration, and the differences of slope values between two types of TNP-celluloses that the more semsitive assay could be achieved by using those from CM 32 as substrate at the low range of the enzyme concentration.

• Journal of Conservation Science
• /
• v.27 no.1
• /
• pp.31-40
• /
• 2011

Copper-red (Dongwha, Jinsa) is Korean traditional inorganic pigment used for red-coloring on the porcelain surface during Goryeo and Joseon Periods. Trace amounts of copper-red porcelains are handed down because of the technical difficulty of making and coloring of the pigment. It is known that copper ore sources were extensively distributed in Korea according to old literatures and some of them are still producing copper ore at this present. Main types of copper-bearing mineral in Korea are chalcopyrite ($CuFeS_2$) and malachite ($Cu_2CO_3(OH)_2$), and they are easily collected from the ground surface. This means Korea had geographical and economic geological advantages for supplying raw material of the pigment. These two minerals showed good red-coloring in color test for porcelain pigment. As a coloring element, copper showed micro size less than $5{\mu}m$ in diameter in glaze matrix. The dispersion of copper particle is the most decisive factor for red chromaticity of copper-red porcelain, as well as copper content of the pigment.