• Journal of the Korean Wood Science and Technology
• /
• v.30 no.1
• /
• pp.11-17
• /
• 2002

This study was performed to determine the characteristics of particleboard made from three-months-old bamboo, (Phyllostachys nigra var henonis Stapf) grown in Damyang district, Korea. Total 60 particleboards were manufactured with 1% of liquid wax emulsion using urea-formaldehyde resin content 9%,11% and 13%, respectively. The particle boards consisted of three layers, in which face layer had the same proportion of a weight 25% of the particleboard each. And the core layer had a weight 50% of the board. The core layer and face layer had the particle dimension passing 6 mesh (3.35 mm), 12 mesh (1.70 mm), respectively. The study was carried out to determine the effect of the growing time of 3 months and 3 years on particleboard properties. The physical and mechanical properties of boards were measured and compared to the Korean standard (KS) requirements of particle boards. The results were as follows; 1. The longer the growing time, the higher the density of bamboo. Density of the upper part of bamboo showed higher than that of lower part. 2. Density and moisture content of the two particle boards did not show significant differences. Three-months-old bamboo particleboard gave higher thickness swelling than three-years-old bamboo particleboard. Bamboo particleboard passed the thickness swelling test of KS. 3. The static bending and internal bond strength of three-months-old bamboo particleboard were higher than those of three-years-old bamboo. Increase of resin contents in bamboo particleboard increased bending and internal bond strength, proportionally. Strength properties of bamboo particle board were above KS. 4. Formaldehyde emission of all the bamboo particleboards satisfied E₂ level (5.0 mg/L) of KS F 3104.

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.4
• /
• pp.393-404
• /
• 2023

This research evaluates the antibacterial and transparency properties of UV-curable paint augmented with 20wt% copper particles. The transparency assessment indicated that the paint maintained a total luminous transmittance of 90% or above, thereby matching or surpassing the performance of standard UV-curing paints. To further test its antibacterial capabilities, wooden flooring boards were coated with the UV-curable paint laced with 20wt% copper particles, which had been surface-modified with a silane coupling agent. Following the fatigue tests of these treated boards, an impressive bacterial reduction rate of 99.9% was noted after a span of 6 hours, demonstrating the paint's exceptional antibacterial performance.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.4
• /
• pp.24-30
• /
• 2003

In order to develop structural 'bamboo zephyr board', properties of boards produced by various methods making zephyr were estimated. All of boards were tested with KS(Korean Standards) F 3014 Particle board, and results were summarized as follow. The zephyr boards produced by final 1.5 mm roller space had the best properties(MOR, MOE and IB strength) among boards produced by different final roller space. Also, they had the best properties(MOR and MOE) in bending test after 1 hour soaking treatment after 2 hour-boiling in water, which were similar to properties of boards in dry-condition. Thickness swelling(TS) of all boards was less than 12% required to the Korean Standards A 3014. Zephyr boards produced by final 1.5 mm roller space also had the lowest values among all of boards. Boards produced by non-treatment (in green condition) had the better strength than those of boards produced by different pre-treatment methods(boiling in water and in 0.3% NaOH) in bending test.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.1
• /
• pp.17-26
• /
• 1996

This research was accomplished to evaluate possibility of using paper sludge for the raw materials of wood based panel products. The experimental panels were manufactured by four mixed ratios, the proportion of paper sludge to wood particle: 20:80, 30:70, 40:60, 50:50% (oven dry weight basis) and by three composition types, sludge-particle mixed board, three layered sludge-particle board and three layered particle board. They were tested mechanical (bending strength and internal bond) and physical properties (water absorption, thickness swelling and linear expansion). From the results they were shown that bending strength of mixed and three layered sludge-particle board were decreased with increasing of composition ratios of sludge. And the mechanical and physical properties of the boards of three layered composition types have superior to those of mixed composition type. Although composition ratios of sludge increased, the internal bond strength and dimensional stability of sludge-particle board not decreased quantitatively. We concluded that the mechanical and physical properties of three layered sludge-particle board were similar w those of three layered particle-board (control) made by our laboratory design. Therefore, it was recognized that paper sludge can be used as potential raw material in particle-board manufacturing industry.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2008.04a
• /
• pp.632-633
• /
• 2008

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.3
• /
• pp.47-58
• /
• 2001

For finding both ways of recycling the wood and plastic wastes and solving the problem of free formaldehyde gas emission through manufacturing wood particle-polypropylene fiber composite board without addition of formaldehyde-based thermosetting resin adhesive, control particleboards and nonwoven web composite boards from wood particle and polypropylene fiber formulation of 50 : 50, 60 : 40, and 70 : 30 were manufactured at density levels of 0.5, 0.6, 0.7, and 0.8 g/$cm^3$, and were tested both in the physical and mechanical properties according to ASTM D 1037-93. In the physical properties, control particleboard had significantly higher moisture content than composite board. In composite board, moisture content decreased with the increase of target density only in the board with higher content of polypropylene fiber and also appeared to increase with the increase of wood particle content at a given target density. Control particleboard showed significantly greater water absorption than composite board and its water absorption decreased with the increase of target density. In composite board, water absorption decreased with the increase of target density at a given formulation but increased with the increase of wood particle content at a given target density. After 2 and 24 hours immersion, control particleboard was significantly higher in thickness swelling than composite board and its thickness swelling increased with the increase of target density. In composite board, thickness swelling did not vary significantly with the target density at a given formulation but its thickness swelling increased as wood particle content increased at a given target density. Static bending MOR and MOE under dry and wet conditions increased with the increase of target density at a given formulation of wood particle and polypropylene fiber. Especially, the MOR and MOE under wet condition were considerably larger in composite board than in control particleboard. In general, composite board showed superior bending strength properties to control particleboard, And the composite board made from wood particle and polypropylene fiber formulation of 50 : 50 at target density of 0.8 g/$cm^3$ exhibited the greatest bending strength properties. Though problems in uniform mixing and strong binding of wood particle with polypropylene fiber are unavoidable due to their extremely different shape and polarity, wood particle-polypropylene fiber composite boards with higher performance, as a potential substitute for the commercial particleboards, could be made just by controlling processing variables.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.4
• /
• pp.360-370
• /
• 2021

For the purpose of finding new uses for Miscanthus sinensis var. purpurascens, this study first constructed boards with the particles of the plant and impregnated them with phenolic resin at resin impregnation rates of 30 ± 2%, 40 ± 2%, 50 ± 2%, and 60 ± 2%. The impregnated boards were then carbonized at the carbonization temperature of 800℃, after which their density and mechanical properties were examined according to the different resin impregnation rates. The results showed that density, flexural strength performance, Brinell hardness, and compressive strength increased as the resin impregnation rate increased, thus affecting the physical and mechanical properties of the ceramics made of M. sinensis var. purpurascens particles.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.2
• /
• pp.109-117
• /
• 2001

This research was carried out to develop the Hanji(Korean paper) sludge wood particle composite utilizing the waste sludges occurring from the making process of Hanji(Korean paper). In the research, four mixing ratios of white or black sludge to wood particle(10:90, 20:80, 30:70, and 40:60), three types of the resin adhesives(PMDI, urea and phenol resin) and three levels of the densities(0.60, 0.75 and 0.90) were designed to investigate the physical properties of Hanji(Korean paper) sludge wood particle composite. The linear expansion of Hanji(Korean paper) sludge wood particle composite was not always increased, compared to control boards. For thickness swelling, PMDI-bonded composites had the lowest value, and thickness swelling of composite was generally decreased with the increase of Hanji sludge. The water absorption of white sludge wood particle composite had no tendency, hut that of black sludge wood particle composite was decreased with an increase of mixing ratio of Hanji sludge.

• Journal of the Korean Society of Visualization
• /
• v.8 no.3
• /
• pp.49-55
• /
• 2010

Thermal flows inside a laser printer are affected by generated heat from a fuser and boards. Thus, the effect of fans has been investigated to control the thermal flows and behaviors of toners. In order to analyze the phenomena experimentally, a PIV (Particle Image Velocimetry) has been used, and then the flow inside the printer has been predicted by the CFD (Computational Fluid Dynamics) in this study to determine the efficient flow distribution by an optimum design of the printer. The determined optimum design has been confirmed by the developed PIV technique so that the efficiency of the laser printer can be improved by the proposed design.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.6
• /
• pp.723-731
• /
• 2014

Nondestructive evaluation (NDE) technique method using a resonance frequency mode was carried out for ceramics made by different carbonizing temperatures (600, 800, 1000, $1200^{\circ}C$) after impregnating the phenol resin with Miscanthus sinensis var. purpurascen particle boards. Dynamic modulus of elasticity increased with increasing carbonizing temperature. There were a close relationship of dynamic modulus of elasticity and static bending modulus of elasticity to modulus of rupture (MOR). However, the result indicated that correlation coefficient was higher in dynamic modulus of elasticity to MOR than that in static modulus of elasticity to MOR. Therefore, the dynamic modulus of elasticity using resonance frequency by free vibration mode is more useful as a nondestructive evaluation method for predicting the MOR of ceramics made by different carbonizing temperature for Miscanthus sinensis var. purpurascens particle boards.