• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.04a
• /
• pp.16-21
• /
• 1993

The study of recycled aggregate concrete in which demolition waste is utilized to produce aggregate for new concrete, can contribute to the solution of two problems. The first is the shortage of aggregate from river, and the second is the waste disposal problem. In comparison with natural aggregate concrete, recycled aggregate concrete shows reductions in compressive strength, tensile strength , vending strength, shear strength and increases in drying shrinkage and creep. Recycled aggregate concrete may also be less durable due to increase in porosity and permeability. Therefore, the purpose of this study is to analyze the applicability of recycled concrete in the influence of a substitute ratio of recycled sand gravel.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.7
• /
• pp.759-766
• /
• 1988

the effect of heat treatment in oxygen ambient on the nucleation and growth of oxidation induced stacking faults(OSF) in n-type(100)silicon wafer has been investigated. The growth of OSF is determind as a function of oxygen concentration in silicon wafer, heat treatment time and temperature, and the activation energy for the growth of OSF can be obtained from the growth kinetics. The activation energies are respectively 2.66 eV for dry oxidation and 2.37 eV for wet oxidation. In this paper, we have also studied the structural feature of OSF with the comparison of optical microscopic morphology and crystalline structure.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.3 no.2
• /
• pp.37-41
• /
• 1979

In order to obtain tasic information for solvent dyeing, polyethylene terephthalate (PET) films was pretreated with water, tetrachloroethylene (TCE) and water/TCE emulsion for three hours at $140^{\circ}C$ for stabilizing the substrate. By film roll cyliderical method, Disperse Red 60, Disperse Yellow 42, and Disperse Blue 27 were diffused in the films and examined dyeing properties. The results are summarized as follows; 1) Diffusion coefficient increases in the order, waterTCE>water/TCE 2) A linear relationship between diffusion coefficient and shrinkage was Observed 3) The temperature dependence of the diffusion coefficient can't be expressed by WLF equation.

• Journal of Korean Society for Quality Management
• /
• v.25 no.1
• /
• pp.135-141
• /
• 1997

The Copper-Clad Laminate (CCL) is a main electronic component of specialtype printed circuit boards (PCBs) such as Silver Through Hole PCB. This CCL should have high reliability under the aging test, and usually the test is done at a higher temperature (110-$150^{\circ}C$) than the normal. Then, this test condition of high temperature may cause such quality problems as hole eccentricity and reduction of distance between part holes. After measuring the CCL shrinkage affected by temperature, the correction factor of a press mold was a, pp.ied to solve these problems. The results showed that the tolerance of hole pitch(${\pm}$$100{\mu}m$) was satisfactory and the internal and external failure costs were reduced by 55%.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.4
• /
• pp.174-182
• /
• 2003

Recently, medical imaging has taken interest on CAD based solution for anatomical part fabrication or finite element analysis of human body. In principle, contours representing object boundary are obtained through image processing techniques. Surface models are then approximated by a skinning method. For this, various methods should be applied to medical images and contours. The major bottleneck of the reconstruction is to remove shape inconsistency between contours and to generate the branching surface. In order to solve these problems, bi-directional smoothing and the composite contour generation method are proposed. Bi-directional smoothing has advantage of removing the shape inconsistency between contours and minimizing shrinkage effect with a large number of iterations. The composite contour by the proposed method ensures smooth transition in branching region.

• Childhood Kidney Diseases
• /
• v.11 no.2
• /
• pp.145-151
• /
• 2007

Hypertonicity (hypernatremia) of extracellular fluid causes water movement out of cells, while hypotonicity(hyponatremia) causes water movement into cells, resulting in cellular shrinkage or cellular swelling, respectively. In most part of the body, the osmolality of extracellular fluid is maintained within narrow range($285-295 mOsm/kgH_2O$) and some deviations from this range are not problematic in most tissue of the body except brain. On the other hand, the osmolality in the human renal medulla fluctuates between 50 and $1,200 mOsm/kgH_2O$ in the process of urine dilution and concentration. The adaptation of renal medullary cells to the wide fluctuations in extracellular tonicity is crucial for the cell survival. This review will summarize the mechanisms of urine concentration and the adaptation of renal medullary cells to the hyper tonicity, which is mediated by TonEBP transcription factor and its target gene products(UT-A1 urea transporter etc.).

• Transactions of Materials Processing
• /
• v.10 no.5
• /
• pp.373-382
• /
• 2001

Die design by computer simulation has some advantages compared with the conventional method which has performed by designer's experiences and trials and errors. The die filling and solidification process of thixoforming process were simulated by MAGMAsoft/thixo module. Furthermore, the die design for thixoforming was performed with the various geometry shape. The effect of designed gate dimension on filling phenomenon was estimated by filling simulation. The calculated results was compared with experimental data. The free surface phenomenon obtained by experiment have good agreement with computer simulation results. The solidification effect much as prosity and shrinkage for designed semi-solid forging die had been predicted by computer simulation. The designed die for semi-solid forging had been applied to produce of the frame part which is used to airconditious system.

• Journal of Powder Materials
• /
• v.7 no.2
• /
• pp.102-109
• /
• 2000

With the emergence of the 3D CAD, it is possible to create a physical part directly from a digital model by accumulating layers of a given material. The technology is being widely used for checking designs, to create master models for rapid tooling, and for reverse engineering. However, in general, a model created by rapid prototyping technology is made of soft material that cannot be used as mass prouduction hard tool. Newly developed powder casting is suitable for rapid-manufacturing metallic tools. Powder casting can serve as a promising rapid tooling method because of high density characteristics and low dimensional shrinkage below 0.1% during sintering and infiltration. Through this process, we have realized significant time and cost savings eliminating the expense of conventional prototype tooling process.

• Design & Manufacturing
• /
• v.2 no.2
• /
• pp.33-37
• /
• 2008

This paper describes the optimization of injection molding conditions to minimize sink marks. Sink marks, which refer to a small depression on the surface opposite a thick wall thickness, are often encounted in injection molded plastic parts. Part geometry, material properties and processing conditions during injection molding can affect the sink mark depth. We designed the runner system which is possible balanced filling to cavities using CAE program and then obtained optimal processing conditions by Taguchi's Robust Design technique. By actual injection molding using optimized mold and molding conditions, it confirmed that sink mark depth decreased zero compared to 1mm level in the conventional mold and process.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.268-271
• /
• 2001

The die design of the liquid and semi-solid forming process is performed by CAE technology, The die design by the computer simulation has some advantages compared with the conventional method which has been performed by the designer's experiences in trials and emu. The defect zones such as porosity and shrinkage has been predicted by simulation results. The result of the numerical analysis for the proposed casting condition shows the characteristics of thixotropic flow, and was used to determine the geometry of the gating system and die cavity. The optimized production conditions were also proposed by result of computer aided engineering.