• Korean Journal of Social Welfare
• /
• v.44
• /
• pp.7-35
• /
• 2001

Little empirical study has been conducted concerning board function effectiveness and organizational performance in nonprofit nongovernmental human service organizations in Korea. Using the evaluations of 107 board members and 17 executive directors in Korean Community Chest and 16 regional community chests, this study attempted to examine the level of board function effectiveness and its relationship with organizational performance in these community chests. This study used board function scale developed by Holland and Jackson (1998) to measure board function effectiveness in the following 6 dimensions: contextual dimension: educational dimension: interpersonal dimension: analytical dimension: political dimension: and strategic dimension. This study showed that using 4 points scale, mean of overall board function effectiveness evaluated by board members is 2.62 and mean of overall board function effectiveness evaluated by executive directors is 2.73. That is, it showed that means of overall board function effectiveness are located in the middle point between negative evaluation and positive evaluation. On the other hand, using parametric correlation analysis method, it was found that in these community chests the association between board function effectiveness and organizational performance measured by fund-raising growth rate in $1999{\sim}2000\;and\;1998{\sim}2000$ is very weak and statistically nonsignificant. This study also revealed that using nonparametric correlation analysis method, the association between consensus level in evaluation by board members and executive directors about board function effectiveness, and organizational performance is still very weak and statistically nonsignificant. Finally, this study discussed the direction of future research in board function effectiveness and its relationship with organizational performance and the areas of board management that requires substantial efforts for promoting effectiveness of nonprofit human service organizations in Korea.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.101-109
• /
• 2010

This paper reports active control of clamped beams using acceleration feedback controllers (AF). The equations of motion of clamped beam under force and moment pairs were derived and the equations of AF controllers were formulated. The effect of the parameters - gain and damping ratio - of the AF controllers on the open loop transfer function was investigated mainly in terms of the system stability. Increasing the gain of the AF controller tuned at a mode, the magnitude of the open loop transfer function is increased at all frequencies. The increase of the damping ratio of the AF controller leads to decrease the magnitude of the open loop transfer function and modifies its phase characteristics to be more stable. Three AF controllers connected in parallel were then proposed. Each AF controller is tuned at the $2^{nd}$, $3^{rd}$ and $4^{th}$ modes, respectively. Their parameters were determined to remain the system to be stable based on the results of the parametric study. A significant reduction in vibration at the 3 modes can be obtained.

• Smart Structures and Systems
• /
• v.20 no.1
• /
• pp.23-33
• /
• 2017

Variable Curvature Friction Pendulum (VCFP) bearing is one of the alternatives to control excessive induced responses of isolated structures subjected to near-fault ground motions. The curvature of sliding surface in this isolator is varying with displacement and its function is non-spherical. Selecting the most appropriate function for the sliding surface depends on the design objectives and ground motion characteristics. To date, few polynomial functions have been experimentally tested for VCFP however it needs comprehensive parametric study to find out which one provides the most effective behavior. Herein, seismic performance of the isolated structure mounted on VCFP is investigated with two different polynomial functions of the sliding surface (Order 4 and 6). By variation of the constants in these functions through changing design parameters, 120 cases of isolators are evaluated and the most proper function is explored to minimize floor acceleration and/or isolator displacement under different hazard levels. Beside representing the desire sliding surface with adaptive behavior, it was shown that the polynomial function with order 6 has least possible floor acceleration under seven near-field ground motions in different levels.

• Journal of the Korean Society of Physical Medicine
• /
• v.8 no.4
• /
• pp.513-523
• /
• 2013

PURPOSE: The purpose of this study was to investigate characteristics of the forced pulmonary function test effect and abdominal muscles activation by combined complex exercise with abdominal drawing-in maneuver training of chronic stroke patients. METHODS: 14 post stroke patients(10 males and 4 females) involved voluntary this study and we divided two groups into CEG(complex exercise group) and CEAG (complex exercise and abdominal drawing-in maneuver group).(n=7, per goup). Each groups implicated the 2 times, 30minute exercises for 6 weeks a day. The CEAG performed the complex exercise 15 minutes and 15 minutes of abdominal drawing-in maneuver. For data analysis, the mean and standard deviation were estimated; non-parametric independent t-test was carried out. RESULTS: According to the study, in the combined complex exercise with abdominal drawing-in maneuver group, FVC and activation of transversus abdominis/internal oblique were statistically significant difference compared to the complex exercise group. CONCLUSION: These results indicate that the combined complex with abdominal drawing-in maneuver was efficient in enhancing abdominal muscles activation and pulmonary function of chronic stroke patients.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.527-535
• /
• 2012

This paper reports the active vibration control of plates using positive position feedback controller (PPF). The equations of motion of the plate under force and moment pairs were derived and the equations of PPF controllers were formulated. The effect of the parameters - gain and damping ratio - of the PPF controllers on the open loop transfer function was investigated mainly in terms of the system stability. Increasing the gain of the PPF controller tuned at a mode, the magnitude of the open loop transfer function is increased at all frequencies without changing the phase behavior. The increase of the damping ratio of the PPF controller leads to decrease the magnitude of the open loop transfer function and to modify its phase characteristics to be more stable. Two PPF controllers connected in parallel, Each PPF controller is tuned at the $1^{st}$ and $2^{nd}$ modes, respectively. Their parameters were determined to remain the system to be stable based on the results of the parametric study. A significant reduction in vibration at the 2 modes can be obtained.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.7
• /
• pp.1104-1113
• /
• 2015

In this paper, we propose Two-Dimensional Robust Face Recognition System Realized with the Aid of Facial Symmetry with Illumination Variation. Preprocessing process is carried out to obtain mirror image which means new image rearranged by using difference between light and shade of right and left face based on a vertical axis of original face image. After image preprocessing, high dimensional image data is transformed to low-dimensional feature data through 2-directional and 2-dimensional Principal Component Analysis (2D)2PCA, which is one of dimensional reduction techniques. Polynomial-based Radial Basis Function Neural Network pattern classifier is used for face recognition. While FCM clustering is applied in the hidden layer, connection weights are defined as a linear polynomial function. In addition, the coefficients of linear function are learned through Weighted Least Square Estimation(WLSE). The Structural as well as parametric factors of the proposed classifier are optimized by using Particle Swarm Optimization(PSO). In the experiment, Yale B data is employed in order to confirm the advantage of the proposed methodology designed in the diverse illumination variation

• Communications for Statistical Applications and Methods
• /
• v.21 no.6
• /
• pp.487-500
• /
• 2014

A new method to calculate the transmittable prevalence of an epidemic disease is proposed based on a back-calculation formula. We calculated the probabilities of reactivation and of parasitemia as well as transmittable prevalence (the number of persons with parasitemia in the incubation period) of malaria in South Korea using incidence of 12 years(2001-2012). For this computation, a new probability function of transmittable condition is obtained. The probability of reactivation is estimated by the least squares method for the back-calculated longterm incubation period. The probability of parasitemia is calculated by a convolution of the survival function of the short-term incubation function and the probability of reactivation. Transmittable prevalence is computed by a convolution of the infected numbers and the probabilities of transmission. Confidence intervals are calculated using the parametric bootstrap method. The method proposed is applicable to other epidemic diseases in other countries where incidence and a long incubation period are available. We found the estimated transmittable prevalence in South Korea was concentrated in the summer with 276 cases on a peak at the $31^{st}$ week and with about a 60% reduction in the peak from the naive prevalence. The statistics of transmittable prevalence can be used for malaria prevention programs and to select blood transfusion donors.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.12
• /
• pp.1190-1199
• /
• 2010

This paper reports active control of clamped beams using acceleration feedback controllers (AF). The equations of motion of clamped beam under force and moment pairs were derived and the equations of AF controllers were formulated. The effect of the parameters - gain and damping ratio - of the AF controllers on the open loop transfer function was investigated mainly in terms of the system stability. Increasing the gain of the AF controller tuned at a mode, the magnitude of the open loop transfer function is increased at all frequencies. The increase of the damping ratio of the AF controller leads to decrease the magnitude of the open loop transfer function and modifies its phase characteristics to be more stable. Three AF controllers connected in parallel were then proposed. Each AF controller is tuned at the 2nd, 3rd and 4th modes, respectively. Their parameters were determined to remain the system to be stable based on the results of the parametric study. A significant reduction in vibration at the 3 modes can be obtained.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.1
• /
• pp.56-64
• /
• 2013

Turbulent boundary layer noise is already a significant contributor to sonar self noise. For developing acoustic window of sonar system to reduce self noise, a parametric study of design factors of acoustic window is presented. Distance of sensor array from acoustic window, materials of acoustic window and characteristics of damping layer are studied as design factors to influence in the characteristics of the transfer function of self noise. As the result, these design factors make change the characteristics of transfer function slightly. Among design factors the location of sensor array is most important parameter in the self noise reduction

• Structural Engineering and Mechanics
• /
• v.74 no.1
• /
• pp.83-90
• /
• 2020

Several classical and higher order plate theories were used to study the buckling of functionally graded material (FGM) plates. In the great majority of research, a power function is used to represent metal and ceramic material transverse distribution (P-FGM). Therefore, the effect of having other transverse variation of material properties on the buckling behavior of thick rectangular FGM plates was not properly addressed. In the present work, this effect is investigated using the Third order Shear Deformable Theory (TSDT) for the case of simply supported FGM plate. Both a sigmoid function and an exponential functions are used to represent the transverse gradual property variation. The plate governing equations are combined with a Navier type expanded solution of the unknown displacements to derive the buckling equation in terms of the pre-buckling in-plane loads. Finally, the critical in-plane load is calculated for the different buckling modes. The model is verified by a comparison of the calculated buckling loads with available published results of Al-SiC P-FGM plates. The conducted parametric study shows that manufacturing FGM plates with sigmoid variation of properties in the thickness direction increases the buckling load considerably. This improvement is found to be more significant for the case of thick plates than that of thin plates. Results also show that this stiffening-like effect of the sigmoid function profile is more evident for cases where the in-plane loads are applied along the shorter edge of the plate.