• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.1
• /
• pp.8-15
• /
• 2015

This paper includes a method for estimating the parameter of a synchronous generator and exciter using the modified particle swarm optimization. A solid round rotor synchronous generator and exciter have been modeled with the saturation function. They are regarded as state of being cooperative to a infinite bus. The behavior characteristic of all particles assigned to a parameter needs to be reflected in the PSO algorithm to fine out more close result to the optimal solution. The results of the simulation to estimate the parameters of the synchronous generator and exciter in the modified PSO algorithm are described.

• Communications for Statistical Applications and Methods
• /
• v.24 no.1
• /
• pp.15-27
• /
• 2017

This paper introduces a two-parameter discrete distribution based on a continuous two-parameter bathtub distribution. It is the only two-parameter discrete distribution that shows a bathtub-shaped hazard function. Some statistical properties of the distribution are discussed. Three different methods are used to estimate its two unknown parameters. The point estimators of the parameters have no closed form. The bootstrap method is used to estimate the distributions of these point estimators. Different approximations of the interval estimations for the two-parameters are discussed. Real data sets are analyzed to show how this distribution works in practice. A simulation study is performed to investigate the properties of the estimations obtained and compare their performances.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.9 s.180
• /
• pp.2353-2360
• /
• 2000

Statistical fatigue properties of metallic materials are increasingly required for reliability design purpose. In this study, static and fatigue tests were conducted and the normal, log-normal, two -parameter Weibull distributions at the 5% significance level are compared using the Kolmogorov-Smirnov goodness-of-fit test. Parameter estimation were compared with experimental results using the maximum likelihood method and least square method. It is found that two-parameter Weibull distribution and maximum likelihood method provide a good fit for static and fatigue life data. Therefore, it is applicable to the static and fatigue life analysis of the spheroidal graphite cast iron. The P-S-N curves were evaluated using log-normal distribution, which showed fatigue life behavior very well.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.304-308
• /
• 2000

In this work, an equation of J-integral for a penny-shaped crack at the end of the cord embedded in rubber matrix is proposed. The dimensional analysis is applied to derived to the equation of J-integral. We assume that the energy Parameter J is separated into the deformation and the geometry function, and which is proved using by separation parameter.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.194-199
• /
• 2000

The creep rate is affected by the temperature and in fact. if the temperature above $T_M/2(T_M:melting\;point)$. The aim of the present investigation is to study the relationship of static creep and cyclic creep behavior of pure copper and the formulation of these phenomena with the special attention to the instantaneous strain. strain rate from time and number of cycles have the same inclination Steady state creep rate depend upon maximum stress and can be expressed as linear function according to Power law creep equations Creep rupture time has relation with creep rate. and it make a group represented as the same direct line regardless of max stress, stress ratio and the temperature. Initial strain effect on continuous creep deformation. and have guantitative relationship between elastic and Plastic strain. LMP have similar tendency than OSDP and MHP according to temperature

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.3
• /
• pp.8-13
• /
• 2008

The paper proposes a model-based measurement of unsteady flow rate by using distributed parameter pipeline model and the measured pressure values at two distant points along the pipeline. The distributed parameter model of hydraulic pipeline is applied with consideration of frequency dependent viscosity friction and unsteady velocity distribution at a cross section of a pipeline. By using the self-diagnostics functions of the measurement method, the validity is investigated by comparison with the measured and estimated pressure and flow rate wave forms at the halfway section on the pipeline. The results show good agreement between the estimated flow rate wave forms and theoretical those under unsteady laminar flow conditions. The method proposed here is useful in estimating unsteady flow rate through an arbitrary cross section in hydraulic pipeline and components without installing an instantaneous flowmeter.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.4
• /
• pp.303-311
• /
• 2005

The problem of conjugate laminar film condensation of the pure saturated vapor in forced flow over a flat plate has been investigated as boundary layer solutions. A simple and efficient numerical method is proposed for its solution. The interfacial temperature is obtained as a root of 3rd order polynomial for laminar film condensation, and it is presented as a function of the conjugate parameter. The momentum and energy balance equations are reduced to a nonlinear system of ordinary differential equations with four parameters: the Prandtl number, Pr, Jacob number, $Ja^{\ast}$, defined by an overall temperature difference, a property ratio R and the conjugate parameter ${\zeta}$. The approximate solutions thus obtained reveal the effects of the conjugate parameter.

• Journal of Ocean Engineering and Technology
• /
• v.18 no.2
• /
• pp.64-69
• /
• 2004

The characteristics of the probability distribution for mechanical properties, e.g. tensile strength, reduction of area, and elongation, for STS304 stainless steel in elevated temperature are investigated. Tensile test is performed by constant crosshead speed controls with 1mm/min. The probability distribution function of measured mechanical properties seems to follow $\alpha$ 3-parameter Weibull, and shows a slight dependence on the temperature. When the temperature is raised, the shape parameter a is increased, but both the scale parameter $\beta$ and location parameter v are decreased.

• Journal of the Korea Safety Management & Science
• /
• v.9 no.5
• /
• pp.43-48
• /
• 2007

This paper is to present linkage parameter to integrate statistical models and physical models for accelerated life test. Statistical models represent the relationship of probability distribution and life. Physical models show the relationship of life and stress. Moreover, this study proposes the four steps for construction of integrated models for accelerated life test using linkage parameter. Finally, this paper develops new integrated models such as extreme value distribution-general Eyring, linearly increasing failure rate function-general Eyring, etc., and estimates various reliability measures.

• Journal of the Korea Safety Management & Science
• /
• v.13 no.1
• /
• pp.203-209
• /
• 2011

This study develops three new models that are practically applicable to three stages of Taguchi's robust design, which includes system design, parameter design and tolerance design. In system design, the Multiple Loss Function Analysis(MLFA) and Overall Loss Index(OLI) which reflect upon weight of characteristics and importance of specification are developed. Moreover parameter design presents Process Capability Index(PCI), $C_{PUK}$ and $C_{PLK}$, in order to segregate Signal-To-Noise Ratio(SNR) into accuracy and precision for an evaluation of relative comparison. In addition, tolerance design presents the new model of allowance computation for assembled product which is primarily derived from safety margin(SM) considering functional limit and specification. The guideline of those three new models, which include systematic charts and applicable illustrations, offers convenience for practitioners in the field. Hence, the practical applications could be made with the steps of robust designs such as system design, parameter design and specification allowance design.