• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제36권3호
• /
• pp.221-227
• /
• 2010

The most common local cause of active gingival bleeding is the vessel engorgement and erosion by severe inflammation. Abnormal gingival bleeding is also associated with the systemic disturbances. Hemorrhagic disorders in which abnormal gingival bleeding is encountered include the following: vascular abnormalities (vitamin C deficiency or allergy), platelet disorders, hypoprothrombinemia (vitamin K deficiency resulting from liver disease), and other coagulation defects (hemophilia, leukemia). There are many conventional methods for gingival bleeding control, such as, direct pressure, electrocoagulation, direct suture, drainage, application of hemostatic agents and crushing and packing. If the active continuous gingival bleeding is not stopped in spite of the application of all conventional bleeding control methods, the life of patient is threatened owing to upper airway obstruction, syncope, vomiting and hypovolemic shock. Therefore, the rapid and correct hemostatic method is very important in the emergency dental care. This is a case report of active gingival bleeding care via dental crown removal and emergency primary endodontic drainage as a last method in liver cirrhosis patient with advanced periodontitis.

• 자원리싸이클링
• /
• 제3권1호
• /
• pp.32-37
• /
• 1994

폐전지로부터 중금속 및 유가금속을 효과적으로 분리, 회수하기 위한 물리적, 화학적 처리기술을 개발함으로써 환경오염문제를 극소화하고 폐자원을 재활용하여 자원의 지속적인 확보와 공급에 기여하고자 이에 대한 기초연구로서 폐수은 전지의 수은제거를 위한 증류실험을 행하였다. 감압 증류실험시 폐전지내 수은은 노 내부온도 $150^{\circ}C$에서 증발되기 시작하여 이를 폐전지로부터 분리, 회수할 수 있었으며 $400^{\circ}C$ 이상에서는 유기물으 열분해가 진행되어 전지내 개스킷 등이 제거되었다. 폐전지의 증류시 내부압력, 반응온도 및 반응시간 등을 변화시키면서 그 영향을 조사하였으며 내부압력 20torr, $250^{\circ}C$에서 8시간 이상 증류실험한 결과 용출액의 수은 함량이 5ppb이하로 환경기준을 만족시켰고, 폐전지내 수은의 99.9%를 회수 할 수 있었다. 또한 전지의 사전 폐쇄없이 온도 증가속도를 $15^{\circ}C$/mm 이상으로, 가열하는 경우 내부 압력의 급격한 증가로 인하여 전지의 파열이 발생하였다.

• 비파괴검사학회지
• /
• 제28권4호
• /
• pp.315-322
• /
• 2008

발전소 밸브는 장시간 동안 고온고압하의 기혹한 조건으로 운전됨에 따라 밸브 시트(seat)면의 이물질 삽입, 시트의 균열, 스템(stem) 패킹(parking) 또는 용접부위 결함 및 피로균열 둥에 의해 누설손상이 발생하고 있다. 이러한 밸브 내부누설 상태를 정밀하게 진단하고 평가하기 위해서는 음향방출기술의 적용이 필요하며, 본 논문은 현장적용이 가능한 연구를 수행하고 그 결과를 소개하고자 한다. 또한 실제 발전소에서 운전되는 다양한 밸브 조건을 토대로 실험실 실험에 의해 주변잡음, 밸브누설시의 음향레벨 및 스펙트럼 특성을 분석하고, 발전소 현장실험 결과와의 비교분석을 통하여, 밸브 누설상태에 따른 주변잡음, 음향신호 및 측정 가능한 최소 누설검출량 등의 평가방법에 대해 고찰하였다. 실험실 실험 및 현장적용 연구결과로부터 밸브누설 여부를 포함한 상태 평가와 최소 측정가능 누설검출량 평가가 가능하였으며, 향후 본 연구는 발전설비 안전운전과 밸브누설로 인한 에너지 손실 예방에 크게 기여할 것으로 기대된다.

• 대한두개안면성형외과학회지
• /
• 제14권1호
• /
• pp.50-52
• /
• 2013

Povidone-iodine (PVP-I, Betadine) has many advantages as a disinfectant solution for preoperative preparations, especially for oral surgery. It is widely used because of its low toxicity and excellent bactericidal effect. The authors report a case of pneumonia secondary due to the aspiration of PVP-I, which was used as an oral disinfectant. We present a case of aspiration pneumonia that resulted from the careless use of PVP-I during preoperative preparation. The patient was a 10-month-old female scheduled for elective surgery to correct a complete cleft of secondary palate. During the preparation of the oral cavity for that cleft palate patient, PVP-I was incidentally aspirated to the airway. The lung resistance was noted with positive pressure and pneumonic infiltration on chest radiograph was seen. The operation was postponed and the patient underwent respiratory care. Three months later, elective palatoplasty under general anesthesia was performed without complication. Based on the experiences of this case, the authors advise that throat-packing should be placed before oral preparation to prevent serious pulmonary complications.

• 한국세라믹학회지
• /
• 제56권1호
• /
• pp.71-76
• /
• 2019

Monochromatic amber phosphor in glasses (PiGs) for automotive LED applications were fabricated with $YAG:Ce^{3+}$, $CaAlSiN_3:Eu^{2+}$ phosphors and Pb-free silicate glass. After synthesis and thickness-thinning process, PiGs were mounted on high-power blue LED to make monochromatic amber LEDs. PiGs were simple mixtures of 566 nm yellow YAG, 615 nm red $CaAlSiN_3:Eu^{2+}$ phosphor and transparent glass frit. The powders were uniaxially pressed and treated again through CIP (cold isostatic pressing) at 200 MPa for 20 min to increase packing density. After conventional thermal treatment at $550^{\circ}C$ for 30 min, PiGs were applied by using GPS (gas pressure sintering) to obtain a fully dense PiG plate. As the phosphor content increased, the density of the sintered body decreased and PiGs containing 30 wt% phosphor had full sintered density. Changes in photoluminescence spectra and color coordination were investigated by varying the ratio of $YAG/CaAlSiN_3$ and the thickness of the plates. Considering the optical spectrum and color coordinates, PiG plates with $240{\mu}m$ thickness showed a color purity of 98% and a wavelength of about 605 nm. Plates exhibit suitable optical characteristics as amber light-converting material for automotive LED applications.

• 한국기계가공학회지
• /
• 제20권12호
• /
• pp.129-135
• /
• 2021

Injection molding is a manufacturing method of melting the polymer resin and injecting it into a mold to molding it into the desired form. Due to the short molding time and outstanding formability, complex products can be shaped with high precision and it is the most widely used polymer molding method. However, there may be areas that are not filled depending on the location of the injection gate where polymer resin is injected. Formability is determined by deformation and surface precision due to the impact of residual stress after molding. Hence, choosing the location of the injection gate is very important and molding analysis of injection molding is essential to reduce the cost of the mold. This study evaluated the injection formability based on the location of the injection gate of the vertical machining center ATC tool port using injection molding analysis and the results were compared and analyzed. Injection molding analysis was conducted on filling, packing, and deformation according to the location of the gate of the ATC tool port. From each injection gate location, filling time, pressure, and maximum deformation were compared. At gate 2, conditions of molding time and the location of the gate were far superior in production and quality. Gate 2 produced the smallest deformation of 0.779mm with the best quality.

• 한국기계가공학회지
• /
• 제21권7호
• /
• pp.84-90
• /
• 2022

The purpose of the cover housing component of a car door is to protect the terminals of the plug housing that connects the electric control unit on the door side to the car body. Therefore, for a smooth assembly with the plug housing and to prevent contaminants from penetrating into the gaps that occur after assembly, the warpage of the cover housing should be minimized. In this study, to minimize the warpage of the cover housing, optimization was performed for design factors related to the mold and processes based on the injection molding simulation. These design factors include gate location, gate diameter, injection time, resin temperature, mold temperature, and packing pressure. To optimize the design factors, Taguchi's approach to the design of experiments was adopted. The optimal combination of the design factors and levels that minimize warpage was predicted through L₁₈-orthogonal array experiments and main effects analysis. Moreover, the warpage under the optimal design was estimated by the additive model, and it was confirmed through the simulation experiment that the estimated result was quite consistent with the experimental result. Additionally, it was found that the warpage under the optimal design was significantly improved compared to both the warpage under the initial design and the best warpage among the orthogonal array experimental results, which numerically decreased by 36.9% and 23.4%, respectively.

• FOCUS: LIFE SCIENCE
• /
• 제1호
• /
• pp.1.1-1.4
• /
• 2024

This article provides comprehensive guidance on the maintenance, cleaning, regeneration, and storage of silica-based HPLC (High-Performance Liquid Chromatography) columns. The general considerations emphasize the importance of using in-line filters and guard cartridges to protect columns from blockage and irreversible sample adsorption. While these measures help, contamination by strongly adsorbed sample components can still occur over time, leading to an increase in back pressure, loss of efficiency, and other issues. To maximize column lifetime, especially with UHPLC (Ultra-High Performance Liquid Chromatography) columns, it is advisable to use ultra-pure solvents, freshly prepared aqueous mobile phases, and to filter all samples, standards, and mobile phases. Additionally, an in-line filter system and sample clean-up on dirty samples are recommended. However, in cases of irreversible compound adsorption or column voiding, regeneration may not be possible. The document also provides specific recommendations for column cleaning procedures, including the flushing procedures for various types of columns such as reversed phase, unbonded silica, bonded normal phase, anion exchange, cation exchange, and size exclusion columns for proteins. The flushing procedures involve using specific solvents in a series to clean and regenerate the columns. It is emphasized that the flow rate during flushing should not exceed the specified limit for the particular column, and the last solvent used should be compatible with the mobile phase. Furthermore, the article outlines the storage conditions for silica based HPLC columns, highlighting the impact of storage conditions on the column's lifetime. It is recommended to flush all buffers, salts, and ion-pairing reagents from the column before storage. The storage solvent should ideally match the one used in the initial column test chromatogram provided by the manufacturer, and column end plugs should be fitted to prevent solvent evaporation and drying out of the packing bed.

• KSBB Journal
• /
• 제20권6호
• /
• pp.458-463
• /
• 2005

Polyurethane foam이 충진된 trickle bed reactor에서 통성혐기성 미생물인 Citrobacter amalonaticus Y19을 이용하여 일산화탄소와 물로부터 연속적인 수소생산을 살펴보았다. C. amalonaticus Y19은 설탕을 탄소원으로 할 때 호기적 조건에서 13 g/L까지 성장하였고 혐기조건에서 CO 가스를 주입하였을 때 약 60시간만에 최대 수소 생산 활성을 나타내었다. TBR 반응기에서 유입가스의 CO의 분압이 증가할수록 혹은 기체 체류시간이 감소할수록 수소 생성속도가 증가하였으나 CO의 전환율은 반대로 감소하였다. 그러나 액상의 유속변화는 반응기 운전 결과에 큰 영향을 주지 못했다. 본 실험에서 얻은 최대 수소 생성속도는 기체 체류시간 25분, 유입 CO 압력 0.4 atm에서 16 mmol/L/hr(전환율 33%)이었다. 이 값은 비슷한 반응기에 대해 보고된 Cowger의 결과보다 약 2배 이상 높은 값으로 통성혐기성균주의 고농도 배양과 다공성 충진물의 사용에 의한 높은 기-액 물질 전달 속도가 그 원인으로 추정되었다.

• 동아시아식생활학회지
• /
• 제18권5호
• /
• pp.692-701
• /
• 2008

This study was conducted with 150 adults of 20 years or older, all of whom lived in Seoul. The awareness of traditional Hangwa (Korean cookies) was shown to be relatively low, with 2.9 points on average, and the intake of traditional Hangwa for a month was 2.1 times. For the reason that traditional Hangwa couldn't become popular, and the opinion that the reason was because the price is expensive was the highest, at 3.8. The next highest reasons given were because it is difficult to buy, and because it is inconvenient to eat, at 3.0. The traditional Hangwa was shown to enjoy positive awareness as opposed to negative awareness, while the manufacturing sanitation was also recognized to be relatively clean, with 2.6 points assigned to the opinion that it doesn't taste good, and 2.7 points assigned to the opinion that the manufacturing sanitation is unclean. With regard to the excellence of traditional Hangwa, the response that 'our tradition can be handed down' was the most often encountered, with a score of 3.9. The traditional Hangwa was appraised as excellent, with 3.6 points assigned to the opinion 'it suits our body because it is made with our agricultural products' and 3.4% for each opinion 'safe ingredients are used' and 'all ingredients are good for health'. With regard to the level of agreement for the development of functional traditional Hangwa, the positive group was higher than 25.3% of the negative group, with 27.3% for 'agree very much' and 22.0% for 'agree'. When converted into a 5-point scale for the development of functional traditional Hangwa, the group that was positive toward its development was high, with 3.4 points on average. All categories of excellence awareness were correlated with the level of agreement for the development of a functional food product (p<0.001). Consumer awareness toward the addition of traditional Hangwa functionality was generally positive, with 3.3 points or higher on average, and awareness of the aging suppression and diabetes control effects of Hangwa was also high, with 3.5 points. Next were Hangwa for diet, Hangwa for blood pressure control, Hangwa for mineral supple-mentation and vitamin additive-type Hangwa, with 3.4 for each, and Hangwa for health preservation, with 3.3 in order. With regard to the degree of interest toward functional traditional Hangwa for the treatment of diseases, obese patients cited aging suppression, at 3.2, and vitamin additive Hangwa, at 3.0, while Hangwa for dieting was assigned 2.8 points. Patients with high blood pressure, blood circulation, and diabetes were all shown as having a high degree of interest in all items, while evidencing particular interest toward Hangwa for diabetes control and Hangwa for blood pressure control. With regard to intention to purchase while developing functional traditional Hangwa, the group asserting intention to purchase was higher than 60% for all items except for Hangwa for diabetes control (58.7%). The Hangwa for aging suppression was highest, at 68.6%, and shown as having intention to purchase during development in the order of vitamin additive Hangwa at 68.0%, Hangwa for mineral supplementation at 64.6%, each of Hangwa for health preservation and Hangwa for blood pressure control at 62.7%, Hangwa for diet at 62.6% and Hangwa for diabetes control at 58.7%. The considerations during the development of functional traditional Hangwa were in the following order: storage at 4.1 points, taste and level of function at 3.9 points, size at 3.5 points, and packing at 3.4 points.