• KSBB Journal
• /
• v.10 no.1
• /
• pp.63-70
• /
• 1995

The effect of operating conditions on separation of soybean proteins in a home-made free-flow electrophoresis apparatus was investigated. Measurement of the pH, conductivity, and UV-absorbance(280 nm) were carried out at each run and the purity of the sample was tested with SDS-PAGE analysis. The soybean extract pretreated with Tris and boric acid was mixed with the amino acids composed of glutamic acid, histidine, arginine, glycine(1 mM each) with glycyl-glycine(2mM) and KCl(1mM). When the cellulose acetate was used as a compartment between the electrode and the buffer solution in the cell, pH distribution in the separation cell varied from 3.0 at the anodic side to 8.0 at the cathodic side and had two inflection point. The applied voltage was from 300V to 1000V and the separation was better at a higher voltage but the voltage was limited by the capability of the cooling system due to Joule heat. The proteins focused near the middle of the channel. From the change of pH and conductivity it was found that the ions in the channel moved out to the electrodes through the membrane. In the case when the concentration of the buffer solution was increased 5 times, proteins were focused at 300V. We could not increase up to the ten times of the concentration since the temperature difference between inlet and outlet was more than $25^{\circ}C$ and denaturation of proteins was expected. When ion-exchange membranes were used U-type pH distribution was set up due to the ionic polarization near the membrane. The commercial ampholytes, instead of the mixed amino acids showed not much improvements in purity of the separated sample.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.3
• /
• pp.82-87
• /
• 1997

Ion-Sensitive Field-Effect Transistors(ISFETs) with LPCVD silicon nitride as a sensitive gate were fabricated on the basis of a CMOS process. The silicon nitride was deposited directly on a poly silicon gate-electrode. Using a specially designed measuring cell, the hydrogen ions sensing properties of the ISFET in liquid could be investigated without any bonding or encapsulation. At first, th sensitivity was estimated by simualtions according to the site-binding theory and the experimental results were analysed and compared with simulated results. The measured dta were in good agreement with the simulated results. The silicon nitride based ISFET has good linearity evaluated from correlation factor ($\geq$0.9998) and a mean pH-sensitivity of 56.8mV/pH. The maximum hysteresis width between forward(pH=3\longrightarrowpH=11)- and backward(pH=11\longrightarrowpH=3) titration was 16.7mV at pH=6.54.

• Korean Journal of Microbiology
• /
• v.29 no.6
• /
• pp.387-391
• /
• 1991

Methylobacterium extorquens AM1 growing on methanol as a sole source of carbon and energy was found to grow most rapidly (t$t_{d}$ =6h) at 30.deg.C in a mineral medium (pH 7.0) containing 0.5% (v/v) methanol which was agitated at 200 rpm (optimal cultivation condition). Cells grown under the optimal cultivation condition contained more spermidine, but less putrescine, than the cells grown on 2.5%(v/v) ( $t_{d}$ =8h ) or at 20.deg.C ( $t_{d}$ =8h ). Cells cultivated under the optimal condition was found to contain more spermidine than the cells grown at pH 6.0 (( $t_{d}$ =7h ) and pH 8.0 ($t_{d}$ =7.3h). the cells growing at the stationary phase under the optimal condition accumulated more spermine or putrescine than the cells growing at the same phase on 2.5%(v/v) methanol or at pH 6.0 and pH 8.0, respectively. M. extorquens AM1 grown in a medium agitated at 100 rpm ( $t_{d}$ =8.8h ) contained less spermidine and spermine than the cells grown under the optimal cultivation condition.

• Honam Mathematical Journal
• /
• v.40 no.3
• /
• pp.549-559
• /
• 2018

In this paper, we consider the congruences involving harmonic numbers and the terms of the sequences {$U_{kn}$} and {$V_{kn}$}. For example, for an odd prime number p, $${\sum\limits_{i=1}^{p-1}}H_i{\frac{U_{k(i+m)}}{V^i_k}}{\equiv}{\frac{(-1)^kU_{k(m+1)}}{_pV^{p-1}_k}}(V^p_k-V_{kp})(mod\;p)$$, where $m{\in}{\mathbb{Z}}$ and $k{\in}{\mathbb{Z}}$ with $p{\nmid}V_k$.

• Clean Technology
• /
• v.10 no.1
• /
• pp.47-51
• /
• 2004

현재 반도체 공정에서 사용되는 세정기술은 대부분이 1970년대 개발된 RCA 세정법인 과산화수소를 근간으로 하는 습식 세정으로, 표면의 입자를 제거하기 위한 SC-1 세정액은 강력한 산화제인 과산화수소에 의한 표면과 입자의 산화와 암모니아에 의한 표면의 에칭이 동시에 일어나 입자를 표면으로부터 분리시킨다. 금속 불순물을 제거하기 위한 SC-2 세정액은 염산과 과산화수소 혼합액을 사용하며 금속 불순물을 용해시켜 알칼리나 금속 이온을 형성하거나 용해 가능한 화합물을 형성시켜 제거한다. 또한 황산과 과산화수소를 혼합한 Piranha 세정액은 효과적인 유기물 제거제로서 웨이퍼에 오염된 유기물을 용해 가능한 화합물로 만들거나 과산화수소에 의해 형성되는 산화막내에 오염물을 포함시켜 불산 용액으로 산화막을 제거할 때 함께 제거된다. 최근 금속과 산화막을 동시에 제거하기 위해 희석시킨 불산에 과산화수소를 첨가한 세정공정이 사용되고 있으며 불산에 의해 표면의 산화막이 제거될 때 산화막내에 포함된 금속 불순물을 동시에 제거시킬 수 있다. 그러나 이와 같이 습식세정액 내에 공통적으로 포함되어 있는 과산화수소의 분해는 그만큼 가속화되어 사용되는 화학 약품의 양이 그만큼 증가하게 되고 조작하기 어려운 단점도 있다. 이를 해결하기 위해 환경친화적인 관점으로 화학약품의 사용을 최소화하는 등 RCA세정을 보완하는 연구가 계속 진행되고 있다. 본 연구에서는 RCA세정법을 환경적으로 대체할 수 있는 세정에 사용되는 전리수의 pH변화에 따른 전리수 분석을 하였다. 전리수의 제조를 위하여 전해질로는 NH4CI (HCI:H2O:NH4OH=1:1:1)를 사용하였다. pH 11 이상, ORP -700mV~-850mV인 환원수와 pH 3 이하, ORP 1000mV~1200mV인 산화수를 제조하였으며, 초순수를 첨가하여 pH 7.2와 ORP 351.1mV상태까지 조절하였다. 이렇게 만들어진 산화수와 환원수를 시간 변화와 pH 변화에 따라 Clean Room 안에서 FT-IR과 접촉각 측정기로 실험하였다. FT-IR분석에서 산화수는 pH가 높아질수록, 환원수는 낮아질수록 흡수율이 낮아졌다. 접촉각 실험에서는 산화수의 pH가 높아질수록 환원수의 pH가 낮아질수록 접촉각이 커짐을 확인하였다. 결론적으로 전리수를 이용하여 세정을 하면, 접촉성을 조절할 수 있어 반도체 세정을 가능하게 할 수 있으며, 환경친화적인 결과를 도출할 것으로 전망된다.

• Analytical Science and Technology
• /
• v.8 no.4
• /
• pp.793-798
• /
• 1995

A new chromoionophore sym-(decyl)(2-hydroxy-5-nitrobenzyloxy)-dibenzo-16-crown-5 (1) has been synthesized for $Na^+$ photometry in aqueous media. Apparent $pK_a$ values of 1 in the presence of 0.10 M LiCl, NaCl, and KCl were measured by spectrophotometry in 50% 1,4-dioxane-50% water (v/v) and compared with the $pK_a$ of 8.68 in the presence of 0.10 M TMACl. A significant $pK_a$ shift to a lower pH was only observed for $Na^+$ (${\Delta}pH=1.31$) due to selective binding of 1 with $Na^+$. Based upon this $pK_a$ shift, chromoionophore 1 was found to selectively respond to $Na^+$ with a detection limit of $10^{-3}M$ and no interference from $K^+$ up to 0.05 M for detection of 10.0 mM $Na^+$ in 50% 1,4-dioxane-50% water (v/v).

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.9
• /
• pp.33-40
• /
• 2022

Sedimentation and pH neutralization has been investigated as preteatment of acid contaminate water. The settling and neutralizing process derive more effective degradation efficiency as the pre-treatment process before the removal process of adsorption, volatile, biodegradation, or oxidation. Settling velocity, uniformity coefficient, coefficient of curvature, and grain size index can define in the sedimentation process for characteristics of the soil. The stainless steel sieve has been used to separate each particle size of the dry soil by assembling in order of 4, 10, 20, 40, 80, 100, and 200 mesh sizes. The soil from Gamcheon Port in Busan drops upper side of the sieve and shakes back and forth to separate each different size of the particle. The 1L of Imhoff cone and 200 mL of the mass cylinder were used as settling tanks to calculate settling velocity. Stokes' equation was used to figure out the average density of dry soil with a value from settling velocity. In the results, the average particle density and lowest settling velocity were 1.93 g/cm³ and 0.11 cm/s, respectively. These values can detect the range of settling points of sediment to prevent chemical accidents. In pH neutralization, the initial pH of 2, 3, 4, and 5 of nitric acid and sulfuric acid are used as an acid solution; 0.1, 0.01, and 0.001 M of sodium hydroxide and calcium hydroxide are used as a base solution. The main goal of this experiment is to figure out the volume percentage of the acid solution becomes pH 7. The concentration of 0.001 M of base solution exceeds all the conditions, 0.01 M exceeds partially, and 0.1 M does not exceed 5 v/v% except pH 2. Calcium hydroxide present less volume than sodium hydroxide at pH neutralization both sulfuric and nitric acid.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.5
• /
• pp.448-454
• /
• 2000

This study was to examine the physicochemical characteristics of coagulation reaction between ignited oyster shell powder (IOSP) and red tide organisms (RTO), and its feasibility, in developing a technology for the removal of RTO bloom in coastal sea,IOSP was made from oyster shell and its physicochemical characteristics were examined for particle size distribution, surface characteristic by scanning electron microscope, zeta potential, and alkalinity and pH variations in sea water. Two kinds of RTO that were used in this study, Cylindrotheca closterium and Skeletonema costatum, were sampled in Masan bay and were cultured in laboratory. Coagulation experiments were conducted using various c(Incentrations of IOSP, RTO, and a jar tester. The supernatant and RTO culture solution were analyzed for pH, alkalinity, RTO cell number, IOSP showed positive zeta potentials of $11.1{\~}50.1\;mV\;at\;pH\;6.2{\~}12.7$, A positive zeta potential of IOSP slowly decreased with decreasing pNa 4,0 to 2,0. When pNa reached zero, the zeta potential approached zero, When a pMg value was decreased, the positive zeta potential of IOSP increased until pMg 3.0 and decreased below pMg 3.0. IOSP showed 4.8 mV of positive zeta potential while RTO showed -9.2 mV of negative zeta potential in sea water. A positive-negative EDL (electrical double-layer) interaction occurred between $Mg(OH)_2$ adsorption layer of IOSP and RTO in sea water so that EDL attractive force always worked between them. Hence, their coagulation reaction occurred at primary minimum on which an extreme attractive force acted because of charge neutralization by $Mg(OH)_2$ adsorption layer of IOSP. As a result, the coagulation reaction was rapidly processed and was irreversible according to DLVO (Deriaguin-Landau-Verwey-Overbeek) theory. Removal rates of RTO were exponentially increased with increasing both IOSP concentration and G-value. The removal rates were steeply increased until 50 mg/l of IOSP and reached $100{\%}\;at\;400\;mg/l$ of IOSP. Removal rates of RTO were $70.5,\;70.5,\;81.7,\;85.3{\%}$ for G-values of $1,\;6,\;29,\;139\;sec^(-1)$at IOSP 100 mg/l, respectively. This indicated that mixing (i.e., collision among particles) was very important for a coagulation reaction.

• Journal of the Korean Chemical Society
• /
• v.38 no.3
• /
• pp.200-207
• /
• 1994

A biosensor for the measurement of L-glutamine has been constructed by immobilizing the slice of Wistar rat kidney and it's organelle on $NH_3$ gas-sensing electrode. The effects of pH, buffer solution, temperature and thickness of slice were investigated in order to optimize electrode response. The tissue sensor had the linearity in the range of L-glutamine concentration $8.0{\times}10^{-5}{\sim}1.0{\times}10^{-2} M$ with a slope of 53.8 mV/decade in 0.05 M phosphate buffer solution, pH 7.8 at $30^{\circ}C$, and optimum thickness of slice and response time were 30 ${\mu}m$ and 3∼5 min, respectively. The organelle sensor showed the linearity within L-glutamine concentration range of $1.2{\times}10^{-4}{\sim}5.0{\times}10^{-3} M$ with a slope of 54.0 mV/decade in 0.05 M phosphate buffer solution, pH 7.8 at $30^{\circ}C$, and response time was 6∼7 min, respectively. Thus, it is clear that the tissue and organelle sensor will be useful for L-glutamine measurements.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.200-203
• /
• 2007

Devices of junction barrier schottky(JBS) structure using 4H-SiC substrates with wide energy band gaps was designed and fabricated. As a measurement results, the device of reverse I-V characteristics was shown as more than 1000 V, its design optimum length of p-grid was $3{\mu}m$ space. In this paper, I-V characteristics was modeled by using of device fabricated process conditions parameters and it was extracted that the I-V property parameters, and it was compared and analyzed with between device parameters and model parameters.