• Journal of the Korean institute of surface engineering
• /
• v.33 no.2
• /
• pp.77-86
• /
• 2000

In this study effects of La starting compounds and substrates on the densification of (P $b_{0.92}$L $a_{0.05}$)Ti $O_3$ thin films were investigated. After the heat treatment on platinized silicon at $650^{\circ}C$ for 30min thickness of PLT(i) thin films (from La-isopropoxide) shrank by 27%, while 33% reduction occurred for PLT (a) thin films (from La-acetate). These PLT(i) films showed less densified surface microstructure compared to the PLT (a) . Lower shrinkage of the films on platinized silicon than on bare silicon (41% and 40% for PLT (i) and PLT (a) respectively) is attributed to the earlier development of crystallinity in the film, which arrests film densification. In order to maximize sintering before crystallization, heat treatment at $400^{\circ}C$ for 3 hours followed by $650^{\circ}C$ for 30 min was attempted. This method increased the shrinkage of the PLT (i) and PLT (a) films two times and 1.5 times as much as that observed for the films heat treated at $650^{\circ}C$ for 30min, respectively. FTIR results indicated that first pyrolysis in the film is associated with the burning of acetate ligands. Condensation reaction between OHs was found to occur preferentially between $350^{\circ}C$ and $450^{\circ}C$, whereas majority of polycondensation between ROH-OH appears to occur until $300^{\circ}C$ and be completed below $450^{\circ}C$.EX>.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.3
• /
• pp.75-80
• /
• 2019

Silicon solar cells have been widely used as a most promising renewable energy source due to eco-friendliness and high efficiency. As modules of silicon solar cells are connected in series for a practical electricity generation, a large voltage of 500-1,500 V is applied to the modules inevitably. Potential-induced degradation (PID), a deterioration of the efficiency and maximum power output by the continuously applied high voltage between the module frames and solar cells, has been regarded as the major cause that reduces the lifetime of silicon solar cells. In particular, the migration of the $Na^+$ ions from the front glass into Si through the anti-reflection coating and the accumulation of $Na^+$ ions at stacking faults inside Si have been reported as the reason of PID. In this research, the thickness effect of $SiO_x$ layer that can block the migration of $Na^+$ ions on the reduction of PID is investigated as it is incorporated between anti-reflection coating and p-n junction in p-type PERC solar cells. From the measurement of shunt resistance, efficiency, and maximum power output after the continuous application of 1,000 V for 96 hours, it is revealed that the thickness of $SiO_x$ layer should be larger than 7-8 nm to reduce PID effectively.

• Journal of the Korean institute of surface engineering
• /
• v.25 no.4
• /
• pp.189-206
• /
• 1992

The effect of activation and electroless nickel plating conditions on contact properties was investi-gated for selective electroless nickel plating of Si wafers in order to obtain an optimum condition of con-tact hole filling. According to RCA prosess, p-type silicon (100) surface was cleaned out and activated. The effects of temperature, DMAB concentration, time, and strirring were investigated for activation of p-type Si(100) surface. The optimal activation condition was 0.2M HF, 1mM PdCl2, 2mM EDTA,$ 70^{\circ}C$, and 90sec under ultrasonic vibration. In electroless nickel plating, the effect of temperature, DMAB concentra-tion, pH, and plating time were studied. The optimal plating condition found was 0.10M NiSO4.H2O, 0.11M Citrate, pH 6.8, $60^{\circ}C$, 30minutes. The contact resistance of films was comparatively low. It took 30minutes to obtain 1$\mu\textrm{m}$ thick film with 8mM DMAB concentration. The film surface roughness was improved with decreasing temperature and decreasing pH of the plating solution. The best quality of the film was obtained at the condition of temperature $60^{\circ}C$ and pH 6.0. The micro-vickers hardness of film was about 800Hv. Plating rate of nickel on the hole pattern was slower than that of nickel on the line pattern.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.167-167
• /
• 2009

결정질실리콘 태양전지를 제조함에 있어 실리콘 기판 내의 금속 불순물들은 소자제작 시에 성능 저하의 원인으로 작용한다. 따라서 본 연구에서는 실리콘 기판에 Cr, Cu, Ni 불순물을 강제 오염시킨 후 태양전지를 제작하여 각각의 불순물에 대한 특성을 조사 하였다. p-type 실리콘 기판을 오염시키기 위해 일정 시간동안 표준용액에 담근 후 질소 분위기에서 열처리 하여 불순물을 확산시켰다. 이후 상용 공정을 이용하여 태양전지를 제작하고 기판내 금속불순물 농도에 따른 태양전지의 동작특성을 분석하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.4
• /
• pp.343-350
• /
• 1995

A Abstract Systematic studies of the effects of crystalline forms of starting powders and p processing variables on the texture of hot - pressed silicon carbide are described. The results I indicate that hot - pressing of $\beta$ - SiC can produce strong textures and composite type duplex microstructure due to the ${\beta} {\rightarrow} {\alpha}$ phase transformation of SiC. The texture variations d during post - annealing have been observed. In the case of using a - SiC as starting pow¬d ders, the degree of preferred orientation by hot - pressing is relatively weak.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04b
• /
• pp.38-41
• /
• 2002

The variation of photoluminescence(PL) properties of Si thin films was investigated by changing deposition temperatures, Si-rich silicon oxide films on p-type (100) Si substrate have been fabricated by pulsed laser deposition(PLD) technique using a Nd:YAG laser. During deposition, the substrates were kept at the temperature range of room temperature(RT) to $400^{\circ}C$. After deposition, samples were annealed at $800^{\circ}C$ in nitrogen ambient, Strong Blue PL has been observed on RT-deposited Si nanocrystallites. When the deposition temperature was increased over $100^{\circ}C$, PL intensities abruptly decreased. The experimental results show the growing mechanism of Si nanocrystallites by PLD.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.3
• /
• pp.307-314
• /
• 1988

The thin, square-diaphragm silicon pressure sensor utilizing shear piezoresistance effect was designed and fabricated and its characteristics were examined. The sensor has only one diffused resistor, whereas conventional full-bridge sensor has four. Sensitivity is somewhat lower but temperature compensation is easier than the latter. The proposed sensor was fabricated with only one p-type diffused resistor of the dimension of 113x85\ulcorner\ulcornerlocated near the center of the edge of the diaphragm. The resistor was at 45\ulcornerwith the edge of the diaphragm. The sensitivity of the sensor was 36\ulcorner/V\ulcornermHg and was linear in the pressure range from 0 to 300 mmHg. The temperature coefficient without temperature compensation was 55 ppm/\ulcorner and it was decreased to about 0.17 mmHg/\ulcorner with compensation in the range from 10 to 60\ulcorner.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.328-331
• /
• 1988

Sealed Interface Local Oxidation (SILO) technology has been investigated using a nitride/oxide/nitride three-layered sandwich structure. P-type silicon substrate was either nitrided by rapid thermal processing, or silicon nitride was deposited by LPCVD method. A three-layered sandwich structure was patterned either by reactive ion etch (RIE) mode or by plasma mode. Sacrificial oxidation conditions were also varied. Physical characterization such as cross-section analysis of field oxide, and electrical characterization such as gate oxide integrity, junction leakage and transistor behavior were carried out. It was found that bird's beak was nearly zero or below 0.1um, and the junction leakages in plasma mode were low compared to devices of the same geometry patterned in RIE mode, and gate oxide integrity and transistor behavior were comparable. Conclusively, SILO process is compatible with conventional local oxidation process.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.566-567
• /
• 2009

We have examined the silicon nitride ($SiN_x$) as gate insulator with the ammonia ($NH_3$) plamsa treatment for the soluble derivatives of polythiophene as p-type channel materials of organic thin film transistors (OTFTs). Fabrications of the jetting-processed OTFTs with $SiN_x$ as gate insulator by $NH_3$ plasma treatment can be similar to performance of OTFTs with silicon dioxide ($SiO_2$) insulator.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.4
• /
• pp.506-514
• /
• 1986

Experimental results are reported concerning temperture effects from room temperature to 100\ulcorner on the optical properties of N-and P-type hydrogenated amorphous silicon films prepared by RF glow discharege. Optical absorption coefficient and optical bandgap have been measured and analyzed as a function of temperature. Optical absorption coefficient increase monotonically with temperature, while the optical bandgape of doped amorphous silicons decrease linearly by about 4-7x10**-4 [ev/k].