• Structural Monitoring and Maintenance
• /
• v.10 no.2
• /
• pp.155-174
• /
• 2023

High performance concrete (HPC) has been extensively used in thin overlay for repair purpose due to its excellent strength and durability. This paper presents an experiment, where the sensor-instrumented HPC overlays have been followed by dynamic strain and moisture content monitoring for 1 year, under normal traffic. The vibrating wire and soil moisture sensors were embedded in overlay before construction. Four given HPC mixes (2 original mixes and their shrinkage-modified mixes) were used for overlays to contrast the strain and moisture results. A calibration method to accurately measure the moisture content for a given concrete mixture using soil moisture sensor was established. The monitoring results indicated that the modified mixes performed much better than the original mixes in shrinkage cracking control. Weather condition and concrete maturity at early age greatly affected the strain in concrete. The strain in HPC overlay was primarily in longitudinal direction, leading to transverse cracks. Additionally, the most moisture loss in concrete occurred at early age. Its rate was very dependent on weather. After one year, cracking survey was carried out by vision to verify the strain direction and no cracks observed in shrinkage modified mixes.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.1
• /
• pp.39-47
• /
• 2016

Repair methods of aging concrete pavement are generally used composite structure pavements, such a composite structure is subjected to a large impact on the mechanical behavior and ensure long-term commonality integrated under vehicle loads, environmental loads of the public in accordance with the bond strength between old and new concrete. A common of bonded concrete overlays that are currently available is Interface arrangements using a variety of equipment to ensure the excellent bond strength between old and new concrete than standard concrete, mixed with a material such as a polymer in order to improve the adhesion with the material itself. However, these method of constructions are being applied, depending on the developer site presents no special specifications apply when a specific application criteria objectively, this is due to the situation of each individual method, which is based on the difficulty in quality control of the site manager. In this study by performing a field test for polymer content via the variables that contribute most significantly to ensure bond strength and the field element core of the interface processing method and materials to ensure bond strength between the old and the new concrete, it was to derive the construction site construction method that can improve the performance of the bond strength through a review of the construction around the correlations and the bond strength according to the effective performance analysis of the conventional surface treatment process and variation of polymer volume fraction.

• Proceedings of the KWS Conference
• /
• 2001.05a
• /
• pp.245-247
• /
• 2001

In this study, the effects of dilution on the wear behavior of PTAW (Plasma Transferred Arc Welding) Inconel 625, Inconel 718 and Stellite 6 overlays on Nimonic 80A were investigated. Inorder to evaluate the wear performance, two-body and three-body abrasive wear test, and dry sliding wear test were performed. According to wear tests, the wear rate of deposit with dilution 30% was higher than that of dilution 10% by 10%, and it was also found the plastic deformation near worn surface.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.28 no.1
• /
• pp.143-152
• /
• 2010

These days, we can't confirm cadastre information about stereoscopic digital map that was consist of 2 dimensions and more difficult to understand of detailed parcel boundary, area, land using for 3 dimensions. An each local government providing three-dimensional that are connected to an aerial photograph with cadastre maps. Satisfaction is high for citizens but, this service additional cost for purchase of an aerial photograph order to provide of it. So far, in various ways are under study about three dimensions using Google Earth which is possible to provides 3 dimensional information by real time for individual parcel situation. The purpose of this study was analyzed an accuracy of overlapping between cadstre maps and an image on Google Earth Web in the each different coordinates system. Also, this paper could be provided for use possibility of 3 dimensions information service with an indicator of using or a guideline of direction for local government which provide 3 dimensions information oneday.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.1
• /
• pp.223-232
• /
• 2014

The feasibility of a virtual colored overlay is based on constraints of computer and user preference and it is evaluated for people with Scotopic Sensitivity Syndrome. We draw ${\alpha}$ and chromaticities of virtual colored overlay which will be implemented on IT devices by measuring optical characteristics of 2 representative film overlays and simulating them. We analyzed the influence of two illuminating conditions on the virtual colored overlay. We find that it is possible to get the multiple combinations of alpha and source RGB values to match a chromaticity which is presented in CIE-Luv color space under ideal white condition of display, a user can select one among them with respect to clarity and comfort. Under 100 lx difference of illumination conditions, the changes of chromaticities are negligible, but luminances are increased $37.8cd/m^2$ average(std 2.006) at high illumination condition.

• Journal of the Korea Concrete Institute
• /
• v.28 no.5
• /
• pp.571-579
• /
• 2016

RS-LMC (Rapid Setting Latex Modified Concrete) has been widely used as repair material for bridge deck overlay or rehabilitation, because the overlaid pavement could be opened to the traffic after 3 hours of curing. Although the field performance of RS-LMC generally indicates that it has an excellent bonding to the substrate and shows a long term performance, the crack by vibration of vehicles have been happened on the overlay of bridges in technical reports. In this study, experimental research was carried out to evaluate the vibration properties of RS-LMC overlays by using P.S.T (Pavement Shaking Table). Total 12 specimens were tested and the variables are Latex-cement ratio (L/C) and amplitude of vibration. The result shows that the number of cracks and the total length of cracks are reduced as the increase of Latex-cement ratio (L/C) until 15%. And the crack occurs at a very small strain than the proposed values by Walter, D, G and design codes.

• The Journal of the Korean dental association
• /
• v.50 no.7
• /
• pp.384-393
• /
• 2012

Successful treatment of a badly broken down tooth with pulpal disease depends not only on good endodontic therapy, but also on good prosthetic reconstruction of the tooth after endodontic therapy is completed. The ideal treatment of endodontically treated teeth has been widely and controversially discussed. Endocrown is a restorative option for endodontically treated teeth. Endocrown design incorporates the core and short post into the crown as a single restoration. The preparation of endocrown consists of a circular equigingival butt-joint margin and central retention cavity of the entire pulp chamber instead of employing intraradicular posts. This design significantly increases the surface area of the preparation available for cementation. It is particularly useful in young patient teeth for long-term provisional restoration and in teeth with short clinical crowns. This technique represents a promising and conservative method for the treatment of endodontically treated teeth that require long-term protection and stability. Endocrown can be considered as a feasible alternative to full crowns or composite overlays for the restoration of non vital teeth.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.7
• /
• pp.591-596
• /
• 2014

Augmented reality is a novel human-machine interaction that overlays virtual computer-generated information on a real world environment. It has found good potential applications in many fields, such as training, surgery, entertainment, maintenance, assembly, product design and other manufacturing operations. In this study, a smartphone-based augmented reality system was developed for the purpose of monitoring and managing injection molding production lines. Required management items were drawn from a management content analysis, and then the items were divided into two broad management categories: line management and equipment management. Effective work management was enabled by providing those working on the shop floor with management content information combined with the actual images of an injection molding production line through augmented reality.

• Journal of Biosystems Engineering
• /
• v.24 no.6
• /
• pp.473-478
• /
• 1999

Recently, it is necessary fir surface materials to be low cost and to keep well endurable and wear in machinery field. Since most good materials with endurance and wear are expensive, they are being studied hard to modify to surface materials with endurance and wear, which overlay with the surface membrane completely. One of them is PTA(Plasma Transferred Arc Overlaying Process) method, which gets into the spotlight. It is thought to be an optimum method, since this method of overlays properly materials with about 3∼5cm surface membrane. It is necessity for the modified materials with endurance and wear to improve within the agricultural environment. Therefore, this research was used the PTA method to endure and wear a material. This method proved to be a reliable method for overlaying the membrane on the materials of an economical agricultural machinery.

• Journal of Welding and Joining
• /
• v.19 no.5
• /
• pp.540-547
• /
• 2001

This study has evaluated the wear behavior of PTA (Plasma Transferred Arc) Inconel 625 and Stellite 6 overlays on Nimonic 80A substrate. Nimonic 80A alloy was also included for comparison. In order to evaluate the wear performance, three-body abrasive wear test and pin-on-disk dry sliding wear test were performed. Microstructural development during the solidification of deposits is also discussed. Wear test results show that the wear rate of Stellite 6 deposit is lower than that of Inconel 625 deposit and Nimonic 80A. The sliding wear resistance of overlay deposits follows a similar trend to the abrasive wear resistance, but for Nimonic 80A. The main wear mechanisms were abrasive wear for Inconel 625 deposit, adhesive wear and delamination for Stellite 6 deposit in pin-on-disk dry sliding wear test and ploughing in three-body abrasive wear test. Cross sectional examinations of the worn surface of pin specimens after pin-on-disk dry sliding wear test implies that the plastic deformation near worn surface has occurred during the wear testing.