• 한국해안해양공학회지
• /
• 제6권3호
• /
• pp.260-265
• /
• 1994

대규모 흐름이 존재하는 불규칙한 해역에서 새로운 타원형 파동방정식을 유도하고, 유한차분법을 이용한 효율적인 수치모형을 개발하였다. 이때 청원형 방정식은 초기식 문제의 해법과 유사한 방법을 사용하여 해를 구하였다. 이 방법은 불규칙파의 변형을 계산하는 데 특히 효과적이며 수리모형 실험결과(Hiraishi, 1991)와 잘 일치하였다. 마지막으로 수중천퇴가 존재하는 완경사 해역에서 파랑과 흐름의 상호작용에 의한 수치해를 예시하였다.

• 한국안전학회지
• /
• 제18권3호
• /
• pp.101-108
• /
• 2003

Polymeric positive temperature coefficient(PTC) composites have been prepared by incorporating carbon black(CB) into high density polyethylene(HDPE), polyphenylene sulfide(PPS) and polybutylene terephthalate(PBT) matrices. A PTC effect was observed in the composite, caused by the large thermal expansion due to He consecutive melting of HDPE, PPS and PBT crystallites. This theory is based upon the premise that the PTC phenomenon is due to a critical separation distance between carbon particles in the polymer matrix at the higher temperature. The influence of PTC characteristics of the PPS/CB composite can be explained by DSC result. HDPE, one of prepared composition, exhibit the higher performance PTC behavior that decreaseing of negative temperature coefficient(NTC) effect and improved reproducibility by chemically crosslinking. Also, PBT/CB and PPS/CB composites exhibit the higher PTC peack temperature than HDPE/CB PTC composite, individually $200^{\circ}C$ and $230^{\circ}C$. These PTC composite put to good use in a number of safety application, such as self$.$controlled heater, over-current protectors, auto resettable switch, high temperature proctection sensor, etc.

• 물과 미래
• /
• 제21권2호
• /
• pp.183-192
• /
• 1988

육붕상의 유동현상을 상세하게 해상시키기 위해 기 보고된 동지나해의 2차원 비선형조석모형(최, 1980)을 위도상 4분, 경도상 5분의 격자간격을 갖는 유한차분격자체계로 개선시켰다. 수립된 세격자모형은 동지나해의 $M_2$ 조석 및 $M_4$조석을 재현시키는데 일차적으로 이용되었는데 산정된 조석체계의 신뢰성은 모형산정치와 황해동측의 조석관측 결과와의 전반적인 일치로서 입증되었다. 육붕전체에 걸친 해저최대마찰응력 및 조석항류의 분포가 제시되었으며 또한 토의되었다.

• Journal of the korean society of oceanography
• /
• 제37권3호
• /
• pp.144-153
• /
• 2002

This is a review paper, assessing progress reported in a Special Issue (Prandle and Lane, 2000) of Coastal Engineering focusing on simulation of SPM in the North Sea, against issues over a diverse range of shelf seas and their coastal margins. The broad objectives of reproducing the characteristics of sediment fluxes off an open coast and relating these to tidal and wave forcing were achieved. However, accurate computation of these fluxes remains sensitive to largely empirical coefficients used in determining erosion and deposition rates. Bed roughness strongly influences both these coefficients and the associated near-bed current magnitudes (including wave impact thereon). Bed roughness can change significantly over a tidal cycle and dramatically over seasons or in the course of a major event. Accurate simulation of sediment fluxes on a day-to-day basis is constrained by dependency on the initial distribution of mobile sediments. The latter depends on rates and locations of original sources and the time history of preceding events. Remote sensing via aircraft could provide data for assimilation into such models to circumvent these constraints. The approaches described here can be readily applied to other coastal regions to indicate the likely distributions and pathways of known sediment sources. However quantitative simulations will require an associated observational programme. A subsequent stage is to understand the evolving balance between the forecasted sediment movement - the resulting morphological adjustments and thence modifications to the prevailing tidal current and wave regimes.

• Journal of the korean society of oceanography
• /
• 제38권2호
• /
• pp.60-67
• /
• 2003

Typhoon Rusa passed over the East China Sea and crossed over the Korea Peninsula on August 31, 2002. The core of the typhoon passed directly over a data buoy mooring site at ($127^{\circ}45'E,\;34^{\circ}25'\;N$) and several ARGOS-tracked drifters capable of measuring salinity. Peak hourly mean wind speed reached 28 m/s at the mooring site and wind pattern in the East China Sea changed from southerly wind to northwesterly wind after the typhoon passage. Two or three days before the typhoon tile drifter displacement changed significantly and the region-wide circulation pattern changed from a northeastward current to a westward current one week after the typhoon had passed. The surface water in the East China Sea was cooled to about $4^{\circ}C$ under the typhoon core and a general cooling occurred in most of the East China Sea with the exception of the Chinese coast. The salinity as observed by the drifters in the East China Sea increased about 2 psu but the near-shore water along the Korean coast observed by the mooring was freshened about 3 psu. The freshening of near-shore water was caused by an intrusion of off-shore water rather than local freshening by typhoon precipitation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.958-960
• /
• 2002

High Temperature Superconducting (HTS) devices make it possible to operate with no electrical loss by resistance. If, however, the applied current is over its critical current, the phase of HTS devices is changed to normal state, so called, quench. In this case, since resistance of HTS is increased abruptly, it can not be avoidable to damage the whole apparatus. In this study, quench detector to protect HTS devices was proposed. We designed the quench detecting circuit and tested the performance of the circuit. The detecting circuit was consisted of Op-Amp and low pass filter etc, to detect very low voltage around $1{\mu}V$. The circuit detected effectively the low voltage when over current is applied to HTS tapes. At the next step, we are going to apply and test the circuit to protect the prototype HTS cable.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1088-1092
• /
• 1995

In this paper, we evaluated the sputter-deposited Cr/Cu thin film fuses on $Al_2O_3$ substrates by the adhesive, breaking and repetitive over-current test as a function of temperature on them. Each Cr and Cu was deposited $1700{\pm}300{\AA},\;3700{\pm}300{\AA}$ using RF sputtering unit. The electroplated Cu of $25{\mu}m$ thickness was added in order to make sensitive thin film fuse of the normal current 15[A]. The adhesive strength and the number of repetition were Increasing and then decreasing with the temperature. The maximum adhesive strength of over $9kgf/9mm^2$ was obtained at $400^{\circ}C$. In the breaking test, the post-arc time characteristic was better than any other factor.

• 한국산업융합학회 논문집
• /
• 제20권4호
• /
• pp.265-273
• /
• 2017

Major industries in Gyeongnam area include robot and automobile manufacturing, shipbuilding, and aviation. According to the research, the mechanical part of the products has been advanced, but awareness over the improvement of quality of the software still lacks. The quality performance test presently conducted by the companies in Gyeongnam is mostly the manual performance test performed by the program manager. In order to systematize this and extend the range of using software testing tools, the current study intends to suggest the necessity for conducting a survey on demand to improve performance and securing testing tools such as measured data analysis. Accordingly, this study is going to investigate 33 companies in Gyeongnam related with software in each of the major business areas centering around the actual field and examine activities related to software quality. And after figuring out the current status of retaining testing tools, the study will suggest the ways to enhance recognition over software quality and propose ultimate solutions to solve the problems on the current stage by finding out how to share information as much as possible in order to lay the foundation for extending the range of activity for the sake of software quality.

• 한국포장학회지
• /
• 제22권3호
• /
• pp.49-58
• /
• 2016

Corrugated board provides packaging for most diverse industries with a share of over 50%, due to the numerous advantages they offer a good protection of the products. In other hand corrugated board fails in environmental conditions, indicating that relative humidity or temperature is higher. These effects directly damage the product packaged. To overcome on this problem recently corrugated boards produced with functional material, "functional corrugated boards," have become more available in the current market. A number of commercialized forms of functional material are coated or composited products with inorganic materials, for example "Nano clay" as representative. However, although the use of functional materials is increasing in corrugated boards, the several concerns such as over cost, environmental friendly materials, recycling, and toxicity affect consumer perceptions and acceptance. In the past, number of researcher focused on process of box compression and the utility of box compression testing etc., best of our knowledge there is no review paper which focus on the functional corrugated boards used in food packaging applications. This paper aims to review the availability of functional corrugated boards in the current market, past research studies on functional material and present the current status of functional corrugated boards in leading countries.

• 조명전기설비학회논문지
• /
• 제26권12호
• /
• pp.1-8
• /
• 2012

The performance and lighting characteristics of the LED depend on cooling condition because the power LED generates lots of heat. In this paper, the effect of the generated heat from power LED module on lighting characteristics and performance is measured and evaluated. For experiments, the transient temperature of a power LED module with cooling condition is measured. In addition, the temperature and lighting characteristics of the LED module are measured during the steady state. As a result, the cooling condition is less effective on the lighting characteristics of the LED module at rated current but the cooling condition extremely affects those of the LED module over the rated current. Because high temperature of the power LED module causes the low phosphor conversion, luminance efficiency becomes low and color temperature becomes high. When power LED module are driven over the rated condition, higher temperature is directly related to lighting characteristics and performance of the LED module rather than higher current.