• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.669-672
• /
• 2001

Generally, previous converter is divided into two categories to get high power factor and good output regulation. These two categories can be combined a category with a main switch. These converter is called Single Stage PFC Converter. This approach has good electrical characteristics of high power factor and fast output voltage regulation. The cost and size are important factor to design the converter in low power system. Even single stage can reduce the size and cost, but this approach needs to have additional circuit like control, PWM circuit. To improve these demerits, Top switch is one of good choice In reduce and size in low power single stage converter. Because it has the ability of current limit, thermal protection, oscillator, control circuit as well as a main switch ability.

• Journal of Power Electronics
• /
• v.7 no.3
• /
• pp.203-212
• /
• 2007

In this paper, a proposed approach to improve the power factor of three-phase rectifiers and to stabilize the output voltage against load change is presented. The elements of the given control strategy are small size, low cost, high performance, and simplicity. The proposed control strategy of switches is based on a prototype of three bi-directional switched consisting of four diodes and one IGBT. A control technique and operational procedure are also developed, both theoretically and experimentally. The experimental results clearly verify the theoretical analysis from the prototype connected to grid unity.

• Journal of Power Electronics
• /
• v.12 no.5
• /
• pp.708-714
• /
• 2012

This paper presents a new interleaved pulse-width modulation (PWM) boost-flyback converter to achieve power factor correction (PFC) and regulate DC bus voltage. The adopted boost-flyback converter has a high voltage conversion ratio to overcome the limit of conventional boost or buck-boost converter with narrow turn-off period. The proposed converter has wide turn-off period compared with a conventional boost converter. Thus, the higher output voltage can be achieved in the proposed converter. The interleaved PWM can further reduce the input and output ripple currents such that the sizes of inductor and capacitor are reduced. Since boundary conduction mode (BCM) is adopted to achieve power factor correction, power switches are turned on at zero current switching (ZCS) and switching losses are reduced. The circuit configuration, principle operation, system analysis, and design consideration of the proposed converter are presented in detail. Finally, experiments conducted on a laboratory prototype rated at 500W were presented to verify the effectiveness of the converter.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.850-852
• /
• 1993

A buck-boost zero current switched(ZCS) series resonant AC to DC converter for the DC output voltage regulation together with high power factor is proposed. A dynamic model for this AC to DC converter is developed and an analysis for the internal operational characteristics is explored. With the proposed control technique, the unity power factor and the DC output voltage regulation without a current overshoot can be obtained.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.6
• /
• pp.539-546
• /
• 1999

A new integrated single-stage zero current switched(ZCS) quasi resonant convertedQRC) for the IX)wer f factor correction(PFCl converter is introduced in this paper. The power factor correction can be achieved by t the discontinuous conduction mod$\varepsilon$(DCM) operation of an input current. The proposed converter has the c characteristics of the good IX)wer factor, 10씨 line current harmonics, and tight output regulation. Furthern10re, t the ringing effect due to the output capacitance of the main switch can be eliminated by use of‘ active clamp c circuit. Therefore, the proIX)sed converter is expecttc'(] to be suitable for a compact power converter with a t tightly regulated output voltage requiring a switching frequency of more than several hundrtc'(]s kHz.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.3
• /
• pp.66-73
• /
• 2019

Recently, FDM-type 3D printer technology has been developed, and efforts have been made to improve the output formability and characteristics further. Through this, 3D printers are used in various fields, and printer technologies are suggested according to usage, such as FDM, SLA, DLP, and SLM. In particular, the FDM method is the most widely used, and the FDM method technology is being developed further. The characteristics of the output are produced by the FDM-type 3D printer, which is determined by various factors, and particularly the perspective of the Inter-Layer Fill Factor, which is the volume ratio of the laminated material that exerts a direct influence. In this study, the Inter-Layer Fill Factor is theoretically obtained by presenting the internal space between each layer according to the laminate thickness as a cross-sectional shape model, and the cross section of the actual laminated sample is compared with the theoretical model through experiments. Then, the equation for the theoretical model is defined, and the strength change according to each condition (tensile strength of material, reduction slope, strength reduction rate, and output strength) is confirmed. In addition, we investigated the influence on the correlation and strength between laminate thickness and the Inter-Layer Fill Factor.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.8
• /
• pp.115-122
• /
• 2017

In this paper, we propose a novel power factor compensation system using slidac. The proposed power factor compensation system compensates the power factor by adjusting the output voltage of the slidac. In the conventional power factor compensation system using capacitor bank method, the power factor compensation error occurs depending on the load condition due to the limitation of the compensation capacitor capacity. However, the proposed system can finely change slidac output voltage applied to the capacitor, therefore power factor can be compensated up to 100% without error. We compare the proposed system with the conventional system, and confirm that the proposed system has excellent power factor compensation performance through simulations and experiments. If the proposed power factor compensation system is applied to an industrial field, a power factor compensation performance can be maximized. As a result, it is possible to reduce of electricity prices, reduce of line loss, increase of load capacity, ensure the transmission margin capacity, and reduce the amount of power generation.

• Progress in Medical Physics
• /
• v.13 no.1
• /
• pp.21-26
• /
• 2002

A practical calculation algorithm which calculates the relative output factor(ROF) for irregular shaped electron field has been developed and evaluated the accuracy of the algorithm. The algorithm adapted two-source model, which assumes that the electron dose can be express as sum of the primary source component and the scattered component from the shielding block. Original two-source model has been modified in order to make the algorithm simpler and to reduce the number of parameters needed in the calculation, while the calculation error remains within clinical tolerance range. The primary source is assumed to have Gaussian distribution, while the scattered component follows the inverse square law. Depth and angular dependency of the primary and the scattered are ignored ROF can be calculated with three parameters such as, the effective source distance, the variance of primary source, and the scattering power of the block. The coefficients are obtained from the square shaped-block measurements and the algorithm is confirmed from the rectangular or irregular shaped-fields used in the clinic. The results showed less than 1.0 ％ difference between the calculation and measurements for most cases. None of cases which have bigger than 2.1 ％ have been found. By improving the algorithm for the aperture region which shows the largest error, the algorithm could be practically used in the clinic, since one can acquire the 1011 parameter's with minimum measurements(5∼6 measurements per cones) and generates accurate results within the clinically acceptable range.

• Journal of Korea Multimedia Society
• /
• v.24 no.8
• /
• pp.1076-1089
• /
• 2021

Among the currently used knowledge-based authentication methods for smartphones, text and graphic-based authentication methods, such as PIN and pattern methods, use a display unit and a touch function of the display unit for input/output of secret information. Recently released smartphone form factors are trying to transform into various forms, away from the conventional bar and slate types because of the material change of the display unit used in the existing smartphone and the increased flexibility of the display unit. However, as mentioned in the study of D. Choi [1], the structural change of the display unit may directly or indirectly affect the authentication method using the display unit as the main input/output device for confidential information, resulting in unexpected security vulnerabilities. In this paper, we analyze the security vulnerabilities of the current mobile user authentication methods that is applied atypical form factor. According to the analysis results, it seems that the existing display-dependent mobile user authentication methods do not consider emerging security threats at all. Furthermore, it is easily affected by changes in the form factor of smartphones. Finally, we propose countermeasures for security vulnerabilities expected when applying conventional authentication methods to atypical form factor-based smartphones.

• Journal of Korea Technology Innovation Society
• /
• v.6 no.3
• /
• pp.328-344
• /
• 2003

This paper is aimed at analyzing the effect of Information Technology (IT) investment on the output growth and Total Factor Productivity (TFP) of Korean stock industry. Data on 24 stock firms for the eleven years (1991-2001) are used for the analysis. It is identified that there are both direct and indirect impacts of IT investment of the Korean stock industry on output growth. The total effect on output growth is 1.34 percentage point per year, which divided into a direct effect of investment in IT on the output growth is 1.97 and an indirect effect on the TFP is -0.63 percentage points per year. Results show that IT investment cannot contribute to increased stock industry productivity. Therefore, the Korean stock industry has not benefited from increased investment on IT in increasing productivity, implying the so-called productivity paradox has existed during the period.