• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1985.10a
• /
• pp.157-160
• /
• 1985

• The KIPS Transactions:PartB
• /
• v.10B no.4
• /
• pp.373-380
• /
• 2003

Most of low cost digital cameras reveal relatively high lens distortion. The purpose of this research is to compensate the degradation of image quality due to the geometrical distortion of a lens system. The proposed method consists of two stages : calculation of a lens distortion coefficient by a simplified version of Tsai´s camera calibration and subsequent image warping of the original distorted image to remove geometrical distortion based on the calculated lens distortion coefficient. In the lens distortion coefficient calculation stage, a practical method for handling scale factor ratio and image center is proposed, after which its feasibility is shown by measuring the performance of distortion correction using a quantitative image quality measure. On the other hand, in order to apply image warping via inverse spatial mapping using the result of the lens distortion coefficient calculation stage, a cubic polynomial derived from an adopted radial distortion lens model must be solved. In this paper, for the purpose of real-time operation, which is essential for embedding into an information device, an approximated solution to the cubic polynomial is proposed in the form of a solution to a quadratic equation. In the experiment, potential for real-time implementation and equivalence in performance as compared with that from cubic polynomial solution are shown.

• Journal of Biomedical Engineering Research
• /
• v.12 no.1
• /
• pp.49-56
• /
• 1991

In this paper, a method for camera position estimation in gasher using elechoendoscopic image sequence is proposed. In orders to obtain proper image sequences, the gasser in divided into three sections. It Is presented thats camera position modeling for 3D information extvac lion and image distortion due to the endoscopic lenses is corrected. The feature points are represented with respect to the reference coordinate system below 10 percents error rate. The faster distortion correction algorithm is proposed in this paper. This algorithm uses error table which is faster than coordinate transform method using n -th order polynomials.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.10 s.352
• /
• pp.97-103
• /
• 2006

This paper presents the method of improving second order intermodulation distortion(IMD2) and dc-offset problems in down-conversion mixer. A simple analysis reveals the IMD2 and dc-offset can be eliminated by controlling the duty cycles of local oscillator(LO) inputs. A mixer with the proposed method has been simulated with a $0.13{\mu}m$ RF CMOS technology with 5% mismatch in the load resistance, the mixer shows 2.04dBm IIP2 and 22mnV input referred DC-offset. By controlling two duty cycles of LO inputs, IIP2 and DC-offset can be improved to 38.8dBm and $777{\mu}V$, respectively.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.4
• /
• pp.1044-1047
• /
• 1998

Non-destructive x-ray inspection system needs image intensifier to obtain the x-ray image. Captured image from image intensifier is distorted because the input plate of image intensifier has a spherical surface. In the research, in order to compensate this image distortion, we created the model of image intensifier and show mathematically that the image distortion was compensated. To show the performance of the proposed method, experiment was performed in real x-ray inspection system.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.100-109
• /
• 2017

This paper proposes performance improvement schemes for sensorless PMSM control drive using a four-switch three-phase inverter (so-called B4 inverter). In the proposed scheme, the back-EMF estimation-based sensorless control algorithm is used to control the brushless PMSM without position sensors. In order to have stable operation, this paper presents a gain adjustment scheme that compensates the reduction of stable sensorless operation range as long as the rotor speed increases. In B4 topology, the center point of dc-link capacitors is connected to 3-phase load, and it is prone to have the load current distortion. Hence, to mitigate this problem, a distortion compensation scheme by modifying voltage commands using measured dc-link potentials is proposed in this paper. The validity of the proposed method is evaluated by simulations and experiments.

• Journal of the Korea Computer Industry Society
• /
• v.7 no.5
• /
• pp.513-520
• /
• 2006

In this paper, we propose a novel real-time frame-layer rate control algorithm using sliding window method for low bit rate video coding. The proposed rate control method performs bit allocation at the frame level to minimize the average distortion over an entire sequence as well as variations in distortion between frames. A new frame-layer rate-distortion model is derived, and a non-iterative optimization method is used for low computational complexity. In order to reduce the quality fluctuation, we use a sliding window scheme which does not require the pre-analysis process. Therefore, the proposed algorithm does not produce time delay from encoding, and is suitable for real-time low-complexity video encoder. Experimental results indicate that the proposed control method provides better visual and PSNR performance than the existing TMN8 rate control method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.28-38
• /
• 2003

Finite element analysis of cylinder heat/block compound under assembly, thermal and firing condition were performed. FE model including two cylinders with gasket, head bolts, liners and valve seats was used. FE modeling method and boundary conditions were introduced. Stress distribution and deformation of cylinder head and block under each loading condition were presented. Gasket pressure distribution and bore distortion level were predicted. Measured data of bore distortion was compared with the analysis results. The analysis result showed similar trends with the experimental data. High cycle fatigue analysis on the basis of this result has been performed in order to find the critical areas of the engine assembly.

• Steel and Composite Structures
• /
• v.4 no.1
• /
• pp.23-36
• /
• 2004

The inelastic lateral-distortional buckling of doubly-symmetric hot-rolled I-section beam-columns subjected to a concentric axial force and uniform bending with elastic restraint which produce single curvature is investigated in this paper. The numerical model adopted in this paper is an energy-based method which leads to the incremental and iterative solution of a fourth-order eigenproblem, with very rapid solutions being obtained. The elastic restraint considered in this paper is full restraint against translation, but torsional restraint is permitted at the tension flange. Hitherto, a numerical method to analyse the elastic and inelastic lateral-distortional buckling of restrained or unrestrained beam-columns is unavailable. The prediction of the inelastic lateral-distortional buckling load obtained in this study is compared with the inelastic lateral-distortional buckling of restrained beams and the inelastic lateral-torsional buckling solution, by suppressing the out-of-plane web distortion, is published elsewhere and they agree reasonable well. The method is then extended to the lateral-distortional buckling of continuously restrained doubly symmetric I-sections to illustrate the effect of web distortion.

• Transactions of Materials Processing
• /
• v.23 no.8
• /
• pp.475-481
• /
• 2014

Water quenching is one method of cooling after hot forming, which is presently being used for the manufacturing of automobile parts. The formed parts at room temperature are heated and then cooled rapidly in a water bath to produce high strength. The formed parts may undergo excessive thermal distortion during the water quench. In order to predict the distortion during water quenching, a coupled thermo-mechanical simulation is needed. In the current study, the simulation of heating and cooling of boron steel cylinders was performed. The material properties for the simulation were calculated from JMatPro, and the convective heat transfer coefficient was obtained from experimental tests. The results show that the thermal distortion and the residual stresses are well predicted by the coupled simulation.