• Journal of Mechanical Science and Technology
• /
• v.20 no.12
• /
• pp.2203-2208
• /
• 2006

Both 1-D and 2-D analytic methods are used for a rectangular fin optimization. Optimum heat loss is taken as 98% of the maximum heat loss. Temperature profile using 2-D analytic method and relative error of temperature along the fin length between 1-D and 2-D analytic methods are presented. Increasing rate of the optimum heat loss with the variation of Biot number and decreasing rate of that with the variation of the fin base length are listed. Optimum fin tip length using 2-D analytic method and relative error of that between 1-D and 2-D analytic methods are presented as a function of Biot numbers ratio.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.4A
• /
• pp.487-495
• /
• 2008

The behavior of nose-deck system during launch was examined by three dimensionless launching parameters, such as the relative flexural stiffness, the relative nose weight, and the relative nose length. The techniques of optimizing the launching nose were illustrated and equations of relationship between relative nose weight and relative nose length were derived under minimum conditions of the launching negative and positive moment. Equations of maximum positive and negative moment were suggested under the conditions. The optimum design method of the launching nose was proposed in launched continuous girder bridges. It was found that the ideal launching nose was to design that with the relative nose weight of 0.167 and the relative nose length of 0.836 to minimize absolute values of the positive and negative moment during launch.

• Journal of Mechanical Science and Technology
• /
• v.16 no.10
• /
• pp.1211-1221
• /
• 2002

A shape optimization of stiffener was conducted to increase buckling load or failure load with stiffened laminated composite panel of I-type under compression loading. Design variables are cap length, web length, and/or thickness under the constraint of volume constancy. The objective function is buckling load and failure load of post-buckling based on Tsai-Hill theory using ABAQUS 5.8 for analysis and Optimizer on Broydon-Fletcher Goldfarb-Sharno Method and Augmented Lagrange Multiplier Method. The effects of relative length of a web and a cap of stiffener on buckling load and failure load of post-buckling were investigated with the results of optimum design.

• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.2
• /
• pp.159-163
• /
• 2004

Data pertaining to first lactation records of 316 Murrah buffaloes, progeny of 47 sires, maintained at NDRI Farm for a period of 18 years were analysed to construct selection indices and to examine their robustness by changing the relative economic values of different economic traits. A total of 120 selection indices were constructed for three sets of relative economic values ( 40 for each set) considering different combinations of seven first lactation traits viz. age at first calving (AFC), first lactation 305 day or less milk yield (FLMY), first lactation length (FLL), first calving interval (FCI), milk yield per day of first lactation length (MY/FLL), milk yield per day of first calving interval (MY/FCI) and milk yield per day age at second calving (MY/ASC). The three sets of relative economic values were based on economic values of different traits, 1% standard deviation of different traits and regression of different traits on FLMY. The 'optimum' indices for the first two sets had five traits each namely AFC, FLMY, FLL, FCI and MY/ASC giving improvement in aggregate genotype of Rupees 269.11 and Rs. 174.88, respectively. The accuracy of selection from both indices was 70.79 and 69.39%, respectively. The 'best' selection index from the third set of data again had five traits (AFC, FLMY, FLL, FCI and MY/FLL) giving genetic gain of Rs. 124.16 and accuracy of selection of 71.81%. The critcal levels or break-even points for FLMY for varying levels of AFC and FCI estimated from the "optimum index" suggested the need of enhancement of present production level of the herd or reduction of AFC or FCI. It was concluded that economic values of various first lactation traits were the most appropriate to construct selection indices as compared to other criteria of assigning relative economic weights in Murrah buffaloes.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.4
• /
• pp.317-326
• /
• 2017

Comparative fishing experiments were conducted in the eastern coastal waters near Uljin, Korea from 2002 to 2004, using the experimental trammel nets to estimate the selectivity for spinyhead sculpin Dasycottus setiger. The inner panels of the nets were made of nylon monofilament with four mesh sizes (82.2, 89.4, 104.8, and 120.2 mm) while its two outer panels were made of twisted nylon multifilament with a mesh size of 510 mm. The SELECT (Share Each Length's Catch Total) procedure with maximum likelihood method was applied to obtain a master selection curve. The different functional models (normal, lognormal, bi-normal, and logistic model) were fitted to the catch data. The lognormal model with the fixed relative fishing intensity was chosen as the best-fitted selection curve through comparison of model deviance and AIC (Akaike's Information Criterion). The optimum relative length (the ratio of fish total length to mesh size) with the maximum relative efficiency was obtained as 2.492.

• Geomechanics and Engineering
• /
• v.8 no.4
• /
• pp.595-613
• /
• 2015

An experimental investigation into the uplift capacity of horizontal square plate anchors in sand with and without geogrid reinforcement is reported. The parameters investigated are the effect of the depth of the single layer of geogrid, vertical spacing of geogrid layers, number of geogrid layers, length of geogrid layers, the effects of embedment depth, and relative density of sand. A series of three dimensional finite element analyses model was established and confirmed to be effective in capturing the behaviour of plate anchor-reinforced sand by comparing its predictions with experimental results. The results showed that the geogrid reinforcement had a considerable effect on the uplift capacity of horizontal square plate anchors in sand. The improvement in uplift capacity was found to be strongly dependent on the embedment depth and relative density of sand. A satisfactory agreement between the experimental and numerical results on general trend of behaviour and optimum geometry of reinforcement placement is observed. Based on the model test results and the finite element analyses, optimum values of the geogrid parameters for maximum reinforcing effect are discussed and suggested.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.52 no.4
• /
• pp.281-289
• /
• 2016

Spinyhead sculpin Dasycottus setiger, a species of cold water fish, is distributed along the eastern coastal waters of Korea. A series of fishing experiments was carried out in the waters near Uljin from June, 2002 to November, 2004, using the experimental monofilament gill nets of different mesh sizes (82.2, 89.4, 104.8, and 120.2 mm) to describe the selectivity of the gill net for the fish. The SELECT (Share Each Length's Catch Total) analysis with maximum likelihood method was applied to fit the different functional models (normal, lognormal, and bi-normal models) for selection curves to the catch data. The bi-normal model with the fixed relative fishing intensity was selected as the best-fit selection curve by AIC (Akaike's Information Criterion) comparison. For the best-fit selection curve, the optimum relative length (the ratio of fish total length to mesh size) with the maximum efficiency and the selection range ($R_{50%,large}-R_{50%,small}$) of 50% retention were obtained as 2.363 and 0.851, respectively. The ratios of body girth to mesh perimeter at 100% retention where the selection curve of each mesh size represented the optimum total length were calculated as the range of 0.86 ~ 0.87.

• Journal of Magnetics
• /
• v.20 no.3
• /
• pp.322-329
• /
• 2015

This paper presents a new overlapped coilgun configuration to launch medium weight projectiles. The proposed configuration consists of a two-stage coilgun with overlapped coil covers with spacing between them. The theoretical operation of a multi-stage coilgun is introduced, and a transient simulation was conducted for projectile motion through the launcher by using a commercial transient finite element software, ANSOFT MAXWELL. The excitation circuit design for each coilgun is reported, and the results indicate that the overlapped configuration increased the exit velocity relative to a non-overlapped configuration. Different configurations in terms of the optimum length and switching time were attempted for the proposed structure, and all of these cases exhibited an increase in the exit velocity. The exit velocity tends to increase by 27.2% relative to that of a non-overlapped coilgun of the same length.

• Asian-Australasian Journal of Animal Sciences
• /
• v.21 no.6
• /
• pp.769-775
• /
• 2008

This study was on the relative net income (RNI) for 18,286 Iranian Holstein cows from 799 herds, with first freshening between 1991 and 2000. Two kinds of production system, which differed mainly in milk pricing system and feed cost, were considered. Four different models adopted from the literature were examined to find the optimum model. They differed by the cost of rearing and growth after first calving and they needed different amounts of economic data at the farm level. Results showed that four measures of RNI were highly correlated (>0.96) and could be used equally to measure lifetime profitability of cows. Therefore, in herds without a regular system for recording economic and management data, use of the simplest model is recommended. Multiple regression analysis revealed that RNI was affected by age at first freshening, milk yield and days of productive life (DPL), regardless of production system, and a similar breeding goal could be defined for the two systems. Multiple regression analysis of RNI showed that in order to obtain an unbiased estimate of economic value for DPL, the per day milk yield, not total lifetime milk yield, should be included in the regression model along with DPL. Regression analysis suggested that it is possible to predict RNI using information on age at first freshening along with the length of first lactation and per day milk yield with a coefficient of determination ranging from 0.44 to 0.47.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.1
• /
• pp.106-114
• /
• 2001

In this study, a shape optimization of stiffener was conducted to increase buckling load or failure load in each case with a different design value and a different objective function for stiffened laminated composite panel of I-type under compression loading. Regarding each of buckling load or failure load as objective function, optimum design was carried out. In respect of optimum design, the effects of relative length of web and cab of stiffener on buckling load or failure load of postbuckling were investigated.