• Membrane Journal
• /
• v.5 no.4
• /
• pp.137-144
• /
• 1995

This studies concern the separation of aqueous boric acid solution and same solution containing silica using cellulose acetate RO S/W 4040 module manufactured by Hydranautics Co. The operating conditions of the applied pressures, temperatures, and feed flow rate are also investigated to characterize the permeabilities, biroc acid recovery, and silica rejection, so that the optimum operating conditions would be found out. In the case where the operating conditions are the temperature 35$^{\circ}$C, The pressure 20atm, and the feed flow rate 2.82 l/min, for the boric acid aqueous solution, the boric acid recovery 58.7% and the permeation rate 2.82 l/min were obtained. And also the results showed the boric acid recovery 68.1% and the permeation rate 1.56 l/min at the operating conditions, 35$^{\circ}$C and 10atm. For the boric acid solution containing silica, when the feed solution are at the conditions of 35$^{\circ}$C and 3.2atm, the boric acid recovery 69.7%, the silica rejection 97.5% and the permeation rate 0.47 l/min were obtained. And the operating conditions were at 35$^{\circ}$C, 20atm and the feed flow rate 2.92 l/min, the results showed the boric acid recovery 56.4%, the silica rejection 96.1% and the permeation rate 2.72 l/min.

• Journal of the Korean Society for Railway
• /
• v.18 no.3
• /
• pp.252-260
• /
• 2015

Ballasted track on an asphalt roadbed can be beneficial for its various effects such as (i) decreasing of roadbed thickness by dispersing train load; (ii) prevention of both strength reduction and weakening in roadbed system by preventing rainwater penetration; and (iii) reducing maintenance cost by preventing roadbed mud-pumping and frostbite. With these beneficial effects, ballasted track on asphalt roadbed has been widely used in Europe and Japan, and relevant research for applying such ballasted track on asphalt roadbed systems in Korea is ongoing. In this study, full-scale static and dynamic train load tests were performed to compare the performance of ballasted track on asphalt roadbed and ballasted track. The optimum thickness levels of asphalt and reinforced roadbeds, corresponding to the design criteria for reinforced roadbed of high-speed railway, was estimated using the FEM program ABAQUS. Test results show that the earth pressure on reinforced roadbed of ballasted track on the asphalt roadbed was relatively low compared with that of simple ballasted track. The elastic and plastic displacements of simple ballasted track on the asphalt roadbed were also lower than those of ballasted track. These test results may indicate that the use of ballasted track on asphalt roadbed is an advantageous system in view of long-term maintenance.

• Restorative Dentistry and Endodontics
• /
• v.26 no.5
• /
• pp.418-435
• /
• 2001

Root canal preparation process is of utmost importance in successful treatment of root canal. Also, one of the most important purpose of the root canal preparation is to enlarge the root canal three dimensionally without changing the curvature of the root canal However as the curvature of the root canal increases, there are many difficulties involved in formation of optimum root canal. Therefore in order to solve the above mentioned problems, new developments in methods of root canal preparation and equipments for such purposes were made. Recently, vigorous studies about newly introduced engine-driven nickel-ti-tanium rotary file are conducted. As shown in research results to dates, it is well established that the use of nickel-titanium file is better suited for curved root canal than stainless steel file in maintaining the curvature or root canal and reducing the deformation of root canal. However it is also acknowledged that there are a few discrepancies in research results according to protocol, due to failure to remove variables in experiments. In addition, although it is recommended by the manufacturer that the GT rotary file should maintain a low rotational speed of 150~350rpm and 'light pressure' as light as not to break the lead of a pencil, academic studies about the vertical force which is not yet standardized are not sufficiently explored. Therefore, this research devised and utilized a special research equipment to standardize the appropriate range of vertical force for GT rotary file through experiments by breaking of the lead of a pencil as expressed by the manufacturer and to accurately measure factors involved through repeating and recreating the environment of root canal preparation. Forming nine experimental groups by varying the vertical forces (150g. 220g, 300g) and rpm (150rpm, 250rpm, 350rpm), the effects of changing vertical forces and rpm on working efficiency were measured in terms of time expended in root canal preparation by crown-down method using a transparent resin block with 35 degree curvature and GT rotary file (z-test). The following research using this special research equipment that involved nine experimental groups and varying the vertical force for root canal preparation from 300g which is within the normal vertical force range to 700g and 1000g which fall outside the normal rpm range. The results were as follows : 1. Analysis of the experiment results revealed that the time spent in root canal preparation decreased as the vertical forces and rpm increased (p<0.05). Also, the effects of rpm were greater than those of the vertical forces within the normal vertical force range ($\beta$-weight test). 2. Observation of the deformation of GT rotary file revealed that deformation increases in a direct correlation with the vertical force increase and in a reverse correlation with the rpm decrease. In the case of the vertical forces close to the normal range, the probability of GT rotary file deformation were quite different depending on the rpm changes. In the case of greater vertical forces, the occurrences of deformation of the file were more frequent regardless of the rpm changes. 3. Deformation and breakage of file were also commonly observed in the expended time measurement experiments and GT rotary file deformation experiments in which low speed rpm (150rpm) was used and at the curved portion of the resin block.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.16 no.3
• /
• pp.27-34
• /
• 1987

The present paper was attempted to obtain the basic date concerning a reasonable preparing method and optimum fermentation conditions of Kochujang (Red pepper paste). To establish the standard quality of Kochujang, the chemical compositions and the volatile components of Kochujang was discussed. The native Kochujang collected from 80 households contained 40.51% of moisture, 6.00% of salts, 3.25 % of crude fat, 10.30 % of crude ash, pH 4.79, 9.28ml of tillable acidity. 19.60% of reducing sugar, 179.51 mg/100g of amino nitrogen and 4.43% of total nitrogen. The volatiles of Kochujang were extracted by a steam-distillation under the reduced pressure and determined by gas chromatography-mass spectrometry (GC-MS). Total volatile components identified in the native Kochujang were 46 components, i. e., 30 components in neutral fraction, 8 components in phenolic fraction and 8 components in acidic fraction, respectively. But no components were detected basic fraction.

• Geotechnical Engineering
• /
• v.8 no.2
• /
• pp.5-20
• /
• 1992

The physical-based and lumped-parameter hydrologic groundwater flow model for predicting the rainfall-triggered rise of groundwater levels in hillside slopes is developed in this paper to assess the risk of landslides. The developed model consists of a vertical infiltration model for unsaturated zone linked to a linear storage reservoir model(LSRM) for saturated zone. The groundwater flow model has uncertain constants like soil depttL slope angle, saturated permeability, and potential evapotranspiration and four free model parameters like a, b, c, and K. The free model parameters could be estimated from known input-output records. The BARD algorithm is uses as the parameter estimation technique which is based on a linearization of the proposed model by Gauss -Newton method and Taylor series expansion. The application to examine the capacity of prediction shows that the developed model has a potential of use in forecast systems of predicting landslides and that the optimal estimate of potential 'a' in infiltration model is the most important in the global optimum analysis because small variation of it results in the large change of the objective function, the sum of squares of deviations of the observed and computed groundwater levels. 본 논문에서는 가파른 산사면에서 산사태의 발생을 예측하기 위한 수문학적 인 지하수 흐름 모델을 개발하였다. 이 모델은 물리적인 개념에 기본하였으며, Lumped-parameter를 이용하였다. 개발된 지하수 흐름 모델은 두 모델을 조합하여 구성되어 있으며, 비포화대 흐름을 위해서는 수정된 abcd 모델을, 포화대 흐름에 대해서는 시간 지체 효과를 고려할 수 있는 선형 저수지 모델을 이용하였다. 지하수 흐름 모델은 토층의 두께, 산사면의 경사각, 포화투수계수, 잠재 증발산 량과 같은 불확실한 상수들과 a, b, c, 그리고 K와 같은 자유모델변수들을 가진다. 자유모델변수들은 유입-유출 자료들로부터 평가할 수 있으며, 이를 위해서 본 논문에서는 Gauss-Newton 방법을 이용한 Bard 알고리즘을 사용하였다. 서울 구로구 시흥동 산사태 발생 지역의 산사면에 대하여 개발된 모델을 적용하여 예제 해석을 수행함으로써, 지하수 흐름 모델이 산사태 발생 예측을 위하여 이용할 수 있음을 입증하였다. 또한, 매개변수분석 연구를 통하여, 변수 a값은 작은 변화에 대하여 목적함수값에 큰 변화를 일으키므로 a의 값에 대한 최적값을 구하는 것이 가장 중요한 요소라는 결론을 얻었다.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.5
• /
• pp.417-423
• /
• 2020

In order to reduce cooling and heating, which is 40% of the energy consumption of buildings, it is important to improve the insulation of the skin. In order to improve the existing insulation, research is being conducted to apply a vacuum insulation panel(VIP) to buildings. However, VIP cannot be repaired, so we considered the metal vacuum insulation panel. Since the core of the metal vacuum pressure and have low thermal conductivity, foam concrete is adopted. However, preliminary experiments confirmed that the time to reach 0.001torr differs depending on the amount and nature of the bubbles. This effect is determined by the type of foaming agent and the density of the bubble slurry, the vacuum delivery time is determined to be the optimum foam concrete conditions are necessary. Therfore, this study aims to present basic data applicable to core materials by measuring vacuum delivery time and thermal conductivity change according to the foaming agent type and foam slurry density of foam large concrete which is core material of metal vacuum insulation panel. Experimental results and analysis show that compressive strength can be used regardless of the type of foam, In terms of thermal conductivity, it is stable to use vegetable foaming agents at 0.9g/㎤ or less. In terms of the vacuum delivery time, the foaming agent appeared similar regardless of the type of foaming agent, but it is considered suitable to use vegetable foaming agent based on compressive strength and thermal conductivity.

• Journal of Life Science
• /
• v.16 no.4
• /
• pp.640-646
• /
• 2006

The present investigation was carried out particularly to optimize the extraction process of Poncirus trifoliata and Prunus mume to develop a functional foodstuff having antibacterial activity against Vibrio parahaemolyticus. The extracts were prepared from the fruits under various conditions, and then optimum extraction conditions were decided in case maximal antibacterial activity was obtained. In extraction process by using hot water, the best antibacterial activity of Poncirus trifoliata was achieved at $80{\sim}100^{\circ}C$ for 30 min, while that of Prunus mume was achieved at $100^{\circ}C$ for 30 min, as showing 14.8 and 16.6 mm of inhibition diameter, respectively. The extraction process with addition of NaOH increased the activity of Prunus mume, but addition of $K_2CO_3$ and $NaHCO_3$ drastically decreased the activity. In the processes at high temperature up to $120^{\circ}C$ by using pressure extractor and with various concentrations of NaOH, the maximum activity was observed in the extract of Prunus mume at $120^{\circ}C$ for 30 min with 0.05 N NaOH. The fermented ethanol extract of the fruits showed less activity than those of the extracts with water and NaOH solution.

• Korean Chemical Engineering Research
• /
• v.56 no.1
• /
• pp.119-124
• /
• 2018

The production of methyl N-phenyl carbamate by an oxidative carbonylation method of aniline and methanol is of great interest as an environmentally friendly process that can replace the monomer production process of a polymer produce using conventional phosgene. In this study, heterogeneous catalysts were prepared by using Y-zeolite, $SiO_2$, $Al_2O_3$ as support, and oxidative carbonylation continuous operation from aniline and methanol was attempted using the prepared heterogeneous catalyst. Batch reactor was used to determine the support, and various reaction conditions such as reaction temperature, reaction pressure, and effect of promoter were established using palladium catalyst. A reaction kinetics study was conducted under optimum reaction conditions. The basic data for carbamate process development were obtained by performing continuous operation for a long time under established reaction condition.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.468-473
• /
• 2016

The aim of this study was to measure the opening force of an access door of a pressurized smoke control zone and verify the reliability of the opening force. For the access door opening force, the opening load of the access door was measured before and after pressurized air had entered the smoke control zone. The reliability of the measured values was verified using the Anderson Darling's statistical analysis method of the Minitab Program. Because the analyzed P values were greater than 0.05 except for some floors before and after the operation of the smoke control equipment, the opening force was found to have 95% reliability. The normal distribution of the measured values showed no relationship with the operation of the smoke control equipment and the precision of the force gauge was believed to be reliable. The major factors for the optimal design of the pressurized smoke control equipment include the precision and reliability of the force gauge, the correct posture of the measuring person, and the same conditions for access doors. Therefore, a digital force gauge is believed to be suitable for measuring the opening force of the access door of a pressurized smoke control zone. In addition, standardization of the posture of a measuring person, the setup of the initial opening force of an access door, etc., are major variables for effective measurements of the door opening force of an access door.

• Analytical Science and Technology
• /
• v.15 no.6
• /
• pp.502-508
• /
• 2002

See-through hollow cathode glow discharge cell has been developed for the trace analysis of metal ions. The systems consists of new glow discharge cell improved the cooling system. In the case of previous type of hollow cathode glow discharge cell, it had been utilized for the trace analysis of metal ions but it had a problem that the plasma becomes unstable by air-cooled device. In this study, the modified hollow cathode glow discharge cell has been developed in order to minimize the problem associated with the air-cooled device. thus the stability of the plasma with water-cooling device has been improved and also the higher plasma temperature has been measured. The fundamental characteristics of modified systems have been investigated. And the discharge parameters, such as discharge pressure, material, and diameter of cathode, have been studied to find optimum discharge conditions.