• Journal of Magnetics
• /
• v.9 no.2
• /
• pp.47-51
• /
• 2004

Giant magneto-impedance (GMI) effect in zero-magnetostrictive Co-based amorphous ribbons samples in their as-quenched and stress-released states as well as with intentionally induced magnetic anisotropy were investigated. Magnetic and impedance properties of the samples exhibiting different anisotropy were compared and the optimum operation conditions for the studied samples from the view-point of their utilization as a sensor element have been determined. A design of a model of magnetic field sensor and characteristics of the constructed prototype are presented.

• Journal of Magnetics
• /
• v.20 no.3
• /
• pp.322-329
• /
• 2015

This paper presents a new overlapped coilgun configuration to launch medium weight projectiles. The proposed configuration consists of a two-stage coilgun with overlapped coil covers with spacing between them. The theoretical operation of a multi-stage coilgun is introduced, and a transient simulation was conducted for projectile motion through the launcher by using a commercial transient finite element software, ANSOFT MAXWELL. The excitation circuit design for each coilgun is reported, and the results indicate that the overlapped configuration increased the exit velocity relative to a non-overlapped configuration. Different configurations in terms of the optimum length and switching time were attempted for the proposed structure, and all of these cases exhibited an increase in the exit velocity. The exit velocity tends to increase by 27.2% relative to that of a non-overlapped coilgun of the same length.

• Journal of the Korean Society for Railway
• /
• v.9 no.5 s.36
• /
• pp.550-554
• /
• 2006

In the early stage of operation of KTX, passengers complained of the excessive cabin noise as the passes the tunnel. The noise is caused partly by wheel-rail contact and partly by airflow around the carbody. In this study, to reduce the cabin noise, the effect of the mud-flaps located between the cars is investigated. A series of tests was conducted to clarify the influences of the type and length of mud-flap, and train speed on the cabin noise. The optimum length of mud-flap was found. The shedding vortices around the mud-flap is thought to be the cause of the aerodynamic noise. Strouhal number and the resonant shedding frequency around the mud-flap correlated well with the cabin noise level.

• Journal of Fisheries and Marine Sciences Education
• /
• v.26 no.4
• /
• pp.894-901
• /
• 2014

This study concerns the performance of condensation heat transfer in two-phase loop thermosyphons. In the present work, R134a has been used as the working fluid. Liquid fill charge ratio defined by the ratio of working fluid volume to total internal volume of thermosyphon, heat flux and wind speed of condensation have been used as the experimental parameters. The results show that the filling rate of working fluid and heat flux are very important factors for the operation of two-phase loop thermosyphons. The optimum liquid fill charge ratio for the best condensation heat transfer rate was 80%.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.573-578
• /
• 2009

Survey shows that temperature accounts for 90.6% of dissatisfaction in general hospital environment. In order to improve this situation, operation and thermal data of S hospital collected in 2006 are analyzed. The objective of this study is to find optimum fiducial temperature that minimizes occupants' complaints using 6 sigma method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.427-428
• /
• 2009

In the manufacture process of refrigerator cabinet, polyurethane(PU) liquid firstly is injected between outer plate and inner case in high temperature about $40^{\circ}C$, and PU foam is generated and solidified to the room temperature. There will be great residual stress in the PU foam, especially at the corners after the whole refrigerator is completely assembled. The stress condition will become more complicated under operating condition because of the large temperature difference between the freezing room and outer plate. And also, there are great differences of properties for plastic and steel which would cause different deformation under temperature gradient. The steel outer plate would expand compared to the PU foam or ABS material under operation condition, which induces a thermally bowing deformation in the refrigerator cabinet. The objective of this paper is to design an optimum bead structure or to use reinforcement in the refrigerator except for improving material properties in order to decrease the deformation.

• Journal of environmental and Sanitary engineering
• /
• v.15 no.4
• /
• pp.98-104
• /
• 2000

Commercial rubber(IR, NR, BR), SBR, and tire were degraded by thermal degradation process. The oil yield of rubbers and tire ranges about 37~86%, it was increased with increase of operation temperature in pyrolysis. And the yield of pyrolytic oil was increased with increase of heating rate. The maximum oil yields of IR, NR, BR, SBR, and tire were 80, 73, 83, 86 and 55% each at $700^{\circ}C$ with a heating rate of $20^{\circ}C$/min, respectively. The pyrolytic oil components were consisted of about 50 aromatic compounds. The calorific value of purolytic oil of commercial rubber, SBR, and tire was measured by calorimeter, it was 39~40 kJ/g. The BET surface area of pyroblack was $47~63m^2/g$. The optimum condition of pyrolysis was operating temperature of $700^{\circ}C$ with heating rate of $20^{\circ}C$. Therefore, the pyrolytic oil and pyroblack are possible to alternative fuel and carbon black.

• Korean journal of food and cookery science
• /
• v.11 no.3
• /
• pp.220-225
• /
• 1995

This study was attempted to standardize preparation methods of Korean foods; Chigae (Stew) such as Deonjang chigae (soybean stew) and Kimchi chigae (Kimchi stew). We followed cooking methods by using cookbooks, food service operation recipes, materials distributed by commercial food restaurants from their own experimental kitchens, and home recipes. Before this recipes were standardized, we thoroughly analyzed and modified them. The total yield and portions were determined together with material weights and procedures. And we evaluated food made by standardized recipes for acceptability, by taste panels from Sookmyung Women＇s University. It concluded that yield volune for doenjang chigae and kimchi chigae after cooking for 10 persons was 3 kg, optimum service temperature was 7$0^{\circ}C$, preparation time was 50 minutes, service volumes by one person was 300 g. This presentantion for the above on food materials and material weights, preparation methods as well as cautions and references are attached in this research paper.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.20 no.5
• /
• pp.43-49
• /
• 1983

In this paper, an architecture for high-speed RNS multiplier were proposed by using com-binational logic circuit. The optimum conditions of moduli set which could be saved hardware and operation time were also considered. In the case of RRNS multiplier, output translation could be achieved effectively by means of the modified CRT with magnitude index. It is shown that the estimated multiplication time is about 31.7 ns in NRNS, whereas 47.95 ns in RRNS, respectively.

• Journal of Environmental Science International
• /
• v.4 no.5
• /
• pp.509-516
• /
• 1995

The treatment performances of anaerobic-aerobic activated sludge process were investigated under various operation conditions. The treatment system proposed in this study gave a relatively stable performance against hourly change of the flow rate and showed a satisfactory removal of nitrogen and phosphorus compounds under experimental conditions. The recycle ratio of mixed liquor from aerobic to anaerobic region and peak coefficient primarily controlled the extent of nitrogen removal. The recycle ratio had the optimum values which were determined by the microbial activities of nitrification and denitrification. The behavior of the treatment unit could be simulated by using the kinetic equations and reactor models which considered the treatment units as complete mixing tanks.