• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.5
• /
• pp.2069-2074
• /
• 2013

The use of the electromagnetic clutch water pump for internal combustion engine vehicles saves fuel and leads to a reduction in emissions. The clutch water pump allows the engine cooling system to select the optimum operation condition by using coolant flow rate on/off control. This study investigated the characteristics of fuel consumption and emissions of the diesel engine cooling system using the clutch water pump. The electromagnetic clutch operation reduced by about 49% of engine warm up period at idle condition and controlled the optimum high coolant temperature at driving condition. Therefore, fuel consumption was enhanced by about 5%, and emissions such as HC, CO and $CO_2$ were also reduced to a certain degree even though NOx increased a little bit, compared to those of the conventional water pump under NEDC mode which represents the real driving pattern.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.5
• /
• pp.445-453
• /
• 2020

The use of tugboats for the safe berthing/unberthing of ships is the most crucial factor in the safe and efficient operation of the harbor. However, the adequate number and size of tugboats that should be held based on the characteristics of the port have not been investigated in detail, which causes disputes between involved parties. Therefore, the suitable number of tugboats and the ratio of the tugboat horsepower were determined in this study using simulation techniques, with focus on Ulsan Port. First, the ship and tugboat-operating models were designed for simulation application. Next, the input variables defined in the model design were standardized in an inputtable form using ARENA software. In addition, the arrival and division process of the ship was designed and simulated as an ARENA model. Finally, the simulation results for six scenarios showed that an effective tugboat operation could be achieved when 42 tugboats were held at Ulsan Port.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.11
• /
• pp.803-808
• /
• 2013

The purpose of this study was performed to investigate the optimum conditions of pH, concrete sludge, seed dosage, mixing intensity, operation time in treating fluoride-containing wastewater as $CaF_2$ using the ready-mixed concrete sludge. Considering fluoride removal, water content, that pH 6, concrete sludge dosage of 10 g/L, Seed dosage ($CaF_2$) of 2 g/L, mixing intensity of 100 rpm and operation time of 60 min were found to be optimum. Correspondingly, removal of fluoride and water content was about 85% and 64%, respectively. Increase in amount of seed dosage did not affect fluoride removal efficiency. but the result that the water content is decreased was shown up in occuring the solid-liquid separation well.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.10
• /
• pp.2231-2238
• /
• 2011

In this paper, the extract method of eye and eye-line from picture of a person is proposed. Most of existing papers are to extract the position of eyeball but in this paper, by extracting not only the position of eyeball but also eye-line, it can be applied to the face application program variously. The experimental data of the input picture is a full face photograph taken by smart phone, basically the picture is limited to the face of one person and back ground can be taken from every where and no restriction of race. The proposed method is to extract face candidated area by using Harr Classifier and set up the candidate area of eye position from face candidate area. To extract high value from eye candidate area using dilate operation, and proposed the method to classify eye and eyelash by local thresholding of the picture. After that, using thresholding image from eyemapC that Hsu's suggested, and separated the area with eye and without eye. Finally extract the contour of eye and detect eye-line using optimum ellipse estimation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.10a
• /
• pp.757-758
• /
• 2010

At the time of medical treatment and surgical operation, halogen lamp and plasma lamp were mainly used as luminous source for lighting. These two luminous sources have drawbacks that the life of lamps are not long, various problems are brought about due to excessive heat generation and its volume is very big because of cooling device. Accordingly, in this research a ring light was developed so that a partial shadowless shooting for the patient's affected area at the medical treatment room and surgical operation room using high luminance LED for which attention is being paid as new lighting parts for medical purpose. LED which was applied to the development used high luminance three color LED for full color for which various color materialization and the adjustment of radiation intensity are possible and we can get white light in order to emphasize the delicate expression for generic tone of shooting object, strong highlight, simple shadow and three dimensional effect at the time of close-up shadowless shooting of the affected area.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.40-40
• /
• 2008

$InGaZnO_4$ based thin film transistors (TFTs) are of interest for large area and low cost electronics. The TFTs have strong potential for application in flat panel displays and portable electronics due to their high field effect mobility, high on/off current ratios, and high optical transparency. The application of such room temperature processed transistors, however, is often limited by the operation voltage and long-tenn stability. Therefore, attaining an optimum thickness is necessary. We investigated the thickness dependence of a room temperature grown $MgO_{0.3}BST_{0.7}$ composite gate dielectric and an $InGaZnO_4$ (IGZO) active semiconductor on the electrical characteristics of thin film transistors fabricated on a polyethylene terephthalate (PET) substrate. The TFT characteristics were changed markedly with variation of the gate dielectric and semiconductor thickness. The optimum gate dielectric and active semiconductor thickness were 300 nm and 30 nm, respectively. The TFT showed low operating voltage of less than 4 V, field effect mobility of 21.34 cm2/$V{\cdot}s$, an on/off ratio of $8.27\times10^6$, threshold voltage of 2.2 V, and a subthreshold swing of 0.42 V/dec.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.4 no.3
• /
• pp.27-42
• /
• 1984

The complexity and expensiveness of water resources projects have made optimum operation and design by computer-based techniques of increasing interest in recent years. Water resources problems in real world need many decisions under numerous constraints. In addition there are nonlinearities in the state and return function. This mathematical and technical troublesome must be overcome so that the optimum operation polices are determined. Then traditional dynamic optimization method encountered two major-cruxes: variable discretization and appearance of constraints. Even several recent methods which based on the Differential Dynamic Programming(DDP) have some difficulties in handling of constraints. This paper has presented New DDP which is applicable to multi-reservoir control. It is intended that the method suggested here is superior to abailable alternatives. This belief is supported by analysis and experiments(New DDT does not suffer course of dimensionality and requires no discretization and is able to handle easily all constraints nonlinearity).

• Journal of Life Science
• /
• v.20 no.11
• /
• pp.1656-1661
• /
• 2010

Alkaline protease for the hydrolysis of egg yolk protein was immobilized on five carriers - Duolite A568, Celite R640, Dowex-1, Dowex 50W and Silica gel R60. Duolite A568 showed a maximum immobilization yield of 24.7%. Optimum pH for the free and immobilized enzyme was pH 8 and 9, respectively. However, no change was observed in optimum temperature ($50^{\circ}C$). Thermal stability was observed in immobilized enzymes compared to free enzymes. The immobilized enzyme retained 86% activity after 10 cycle operations in a repeated batch process. The effect of flow rate on the stability of enzyme activity in continuous packed-bed reactor was investigated. Lowering flow rate increased the stability of the immobilized enzyme. After 96 hr of continuous operation in a packed-bed reactor, the immobilized enzyme retained 83 and 61% activity when casein and egg yolk were used as a raw materials, respectively.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.2
• /
• pp.325-335
• /
• 1992

In this work, direct contact 4-stage fluidized bed heat exchanger is experimentally studied to develop a new type of heat exchanger which recovers the energy contained in the high temperature waste gas exhausted from the industrial furnaces. A sand is used as a heat transfer medium in this experiment. To determine the optimum operating condition, 11 different perforated plates which have a different free area ratio with different hole diameter are used in the experiment. From the room temperature experiment, the pressure drop which is caused by fluidized bed formation is observed. The high temperature experiment is carried out to seek the optimum operating condition of high heat efficiency at low heat exchanger operation cost. The results of experiment are as following. The pressure drop in the high temperature condition can be predicted from the results of the room temperature experiment. And Nusselt number becomes smaller due to the increased interference between sand particles as Reynolds number increases when the dilute phase fluidized beds are formed in nigh temperature condition. But heat transfer amount through the total sand surface area become larger due to the large resident amount of sand. Considering the heat transfer amount and the heat exchanger operation cost, perforated plates which have either a 30% or 35% of free area ratio with 15mm of hole diameter are best fitted for our goal of this work. The values of .phi. which is a dimensionless number representing the absorption heat amount per unit sand rate are in the range from 0.4 to 0.5, when Reynolds number of waste gas ranges from 25-30 with these perforated plates.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.2
• /
• pp.167-172
• /
• 2010

CANDU spent fuel is to be disposed of at repository finally rather than recycled because of its low fissile nuclide concentration. But the difficult situation of finding a repository site can not help introducing a interim storage in the short term. It is required to find an optimum timing of geological disposal of CANDU spent fuels related to the interim storage operation period. The major factors for determining the disposal starting time are considered as safety, economics, and public acceptance. Safety factor is compared in terms of the decay heat and non-proliferation. Economics factor is compared from the point of the operation cost, and public acceptance factor is reviewed from the point of retrievability and inter-generation ethics. This paper recommended the best solution for the disposal starting time by analyzing the above factors. It is concluded that the optimum timing for the CANDU spent fuel disposal is around 2041 and that the sooner disposal time, the better from the point of technical and safety aspects.