• Transactions on Electrical and Electronic Materials
• /
• v.9 no.6
• /
• pp.260-264
• /
• 2008

The operational characteristics of superconducting amplifier using vortex flux flow were analyzed from an equivalent circuit in which its current-voltage characteristics for the vortex motion in YBCO microbridge were reflected. For the analysis of operation as an amplifier, dc bias operational point for the superconducting amplifier is determined and then ac operational characteristics for the designed superconducting amplifier were investigated. The variation of transresistance, which describes the operational characteristics of superconducting amplifier, was estimated with respect to conditions of dc bias. The current and the voltage gains, which can be derived from the circuit for small signal analysis, were calculated at each operational point and compared with the results obtained from the numerical analysis for the small signal circuit. From our paper, the characteristics of amplification for superconducting flux flow transistor (SFFT) could be confirmed. The development of the superconducting amplifier applicable to various devices is expected.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.6
• /
• pp.271-277
• /
• 2003

It is important to control layer current distributions of coaxial multi-layer HTS cables, because a homogeneous layer current distribution decreases AC loss and can supply the largest operational current. We have extended the theory that treat the operational current more than the critical current by considering V-I nonlinear characteristics of HTS tapes including flux flow resistance and contacting resistance between the cable and terminals. It is important to investigate the current distribution under the condition of operational current more than the critical current of cable, because the cable has experiences of fault current. In order to verify the extended theory, we have fabricated a two layers cable with the same twisting layer pitch. It was observed that almost all the operational current less than the critical current flowed on the outer layer because of its lower inductance. In case of operational current more than critical currents of layers, the flux flow resistances affect strongly current waveform and thereby the currents of layers were determined by the flux flow resistances. And we investigated breakdown characteristics in $LN_{2}$/paper composite insulation system for the application to a HTS cable. In this experiment, we got some information out of that the electrical characteristics of the insulation materials depends on the condition of butt gap.

• Journal of Sensor Science and Technology
• /
• v.1 no.1
• /
• pp.13-21
• /
• 1992

We have constructed the magneto-operational amplifier(MOP) using the advantages of Hall device and an operational amplifier. The MOP necessarily requires a high impedance circuit, a differential-to-single-ended convert-sion circuit and feedback-input-element for operational amplifier characteristics. We have presented a new differential-to-single-ended conversion operational amplifier(DSCOP) having such characteristics. We have designed the MOP using the DSCOP and Hall device and simulated its characteristics, and finally we have constructed the system with discrete elements, and measured its magnetic characteristics.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.1
• /
• pp.1171-1177
• /
• 2001

This paper provides a guideline for specifying the operational compliance characteristics considering the location of compliance center and the grasp points in assembly tasks using robot hands. Through various assembly tasks, we analyze the conditions of the achievable operational stiffness matrix with respect to the location of compliance center and the grasp points. Also, we show that some of coupling stiffness elements in the operational space cannot be planned arbitrarily. As a result it is concluded that the location of compliance center on the grasped object and the grasp points play important roles for successful assembly tasks and also the operational stiffness matrix should be carefully specified by considering those conditions.

• Structural Engineering and Mechanics
• /
• v.74 no.1
• /
• pp.121-128
• /
• 2020

This paper presents an experimental study on the dynamic characteristics of infilled reinforced concrete (RC) frames. A 1/3-scaled, one-bay, three-storey RC frame was produced and tested by using operational modal analysis (OMA). The experiments were performed on five specimens: one reference frame with no infill walls and four frames with infill walls. The RC frame systems included infill walls made of hollow clay brick, which were constructed in four different patterns. The dynamic characteristics of the patterns, including the frequency, mode shapes and damping ratios in the in-plane direction, were obtained by 6 accelerometers. Twenty-minute records under ambient vibration were collected for each model, and the dynamic characteristics were determined using the ambient vibration testing and modal identification software (ARTeMIS). The experimental studies showed that the infill walls significantly affected the frequency value, rigidity and damping ratio of the RC frame system.

• Korean journal of food and cookery science
• /
• v.11 no.3
• /
• pp.295-302
• /
• 1995

The purposes of the study were to identify the operational characteristics in employee feeding facilities, and to examine the correlations of productivity and these characteristics. A questionnaire was developed and mailed the 500 dietitians in employee feeding facilities in Seoul and Kyoungki Do. Usable questionnaires were received from 117 respondents for a response rate of 23.4％. The questionnaire was designed to determine the productivity index and to investigate the relationship between operational characteristics and productivity index. The questionnaire was contained 2 parts with a total of 16 statements. Data were analyzed for descriptive statistics and Pearson correlation analysis using SPSS/PC programs. The average productivity indices of 117 facilities were 6.91 meals/hr. Total meals served/week was significantly correlated to the productivity index (r=0.441, p < 0.001). No of average servings per meal, percentage of convenience food use, average minutes for service/day, and employment in professional practice of dietitian were also positively correlated, while food cost was negatively correlated to the productivity.

• Computers and Concrete
• /
• v.12 no.1
• /
• pp.79-90
• /
• 2013

In this study, dynamic characteristics such as natural frequencies, mode shapes and damping ratios of RC frame is determined for different construction stages using Operational Modal Analyses method under ambient vibration. Full scaled, one bay and one story RC frames are selected as an application for different construction stages such as plane, brick in-filled and brick in-filled with plaster. The RC frame is vibrated by natural excitations with small impact effects and the response signals are measured using sensitive accelerometers during ambient vibration tests. Measurement time-frequency span and effective mode number are determined by considering similar studies in literature. Sensitive seismic accelerometers are used to collect signals obtained from the experimental tests. To obtain experimental dynamic characteristics, output-only system identification technique is employed namely; Enhanced Frequency Domain Decomposition technique in the frequency domain. It is demonstrated that the ambient vibration measurements are enough to identify the most significant modes of RC frames.

• Journal of National Security and Military Science
• /
• s.3
• /
• pp.73-120
• /
• 2005

Today's world is generation of Transformation. The Term "Transformation" is widely used in many nations and international organizations such as U.S. and NATO to describe the course of change undertaken by militaries to respond to the new and emerging security environment. Transformation involves all elements of the defense enterprise including Operational Environment, Operational Concepts, Doctrine, Structure and Technologies, within a supportive Cultures context. An Operational Environment is defined as "a composite of conditions, circumstances, and influences that affect the employment of military forces and bear on the decisions of the unit commander." The context for developing future military concept and capability lies essentially within the anticipated boundaries of the operational environment in a collective sense. The joint operational environment is essential to the nation's defense. It describes volatile, complex, and dangerous environment in which the military personnel. organizations, and material will operate. Implications coming forth from joint Operational Environment are but a starting point - many others exist. More and better Implications will come forth as people think about massages of Operational Environment, experiment its characteristics, learn to deal with its threats and scenarios, apply their experience and judgement, and then consider what is required of Korean military doctrine, organizations, training and education, material development, and leadership for operations in the joint Operational Environment.

• Journal of Korea Port Economic Association
• /
• v.27 no.3
• /
• pp.13-39
• /
• 2011

Many previous studies on the subject of supply chain have consistently claimed that they need collaboration among the partners of supply chains in order to enhance supply chain performance. The purpose of research is to examine the causal linkages among relational characteristics, collaboration, performance in the logistics firm and this research focuses on two types collaboration(operational collaboration and strategic collaboration) as the mediation variable between relational characteristics and supply chain performance. To test the above research questions, we collected data from logistics firm(N=164). The proposed structural model was tested using the PLS(Partial Least Square) statistical program. The research results are as follows. Trust, and information sharing have positive influences on operational collaboration, and operational collaboration have also positive influences on supply chain performance. Duration and information sharing have positive influences on strategic collaboration. However, strategic collaboration has non-positive influences on supply chain performance. The effect of relational characteristics on supply chain performance is mediated by operational collaboration.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.27 no.1
• /
• pp.107-113
• /
• 2017

The dynamic characteristics including natural frequencies and excitation frequencies are evaluated for a small 10 kW vertical axis wind turbine. Acceleration responses were measured at 12 distributed locations for impact vibration tests, ambient vibration tests during non-operational and operational conditions, and braking tests during operational condition. The natural frequencies for the lowest 2 bending modes and the first torsional mode were estimated and also the excitation frequencies, i.e. 1P, 2P, 4P, were also estimated according to the rotational speed using the responses under operational conditions (i.e. power generation condition).