• Environmental and Resource Economics Review
• /
• v.19 no.4
• /
• pp.733-752
• /
• 2010

This study applies the Luenberger indicator approach to estimate productivity of the Korean fossil-fueled power plants. A panel data set of 25 power plants was used. The method incorporates $CO_2$ emission as an undesirable output and shows that ignoring $CO_2$ emission overestimates the productivity change. There are two sources of overestimation. First, the usual method estimates productivity change ignoring the increase in $CO_2$ emission that occurred during the study period. Second, the productivity change estimated by the usual method that does not incorporate $CO_2$ emission is very sensitively affected by the change in operation rate. The paper decomposes the productivity change into the efficiency change and the technical change. The results show that the two sources contribute to the productivity change almost equally. It is also shown that the size and the pattern of productivity change are dependent on the plants' fuel types. Non-LNG power plants which saved their energy consumption and thereby reduced their $CO_2$ emission have achieved relatively high rate of productivity improvement.

• Applied Biological Chemistry
• /
• v.41 no.2
• /
• pp.181-186
• /
• 1998

The effects of sewage treatment on characteristics of sludge as a composting material were investigated for a year during the initial operation at the full-scale Chunan sewage treatment plant. Due to the shortage of design capacity of belt press, a sludge dewatering unit, non-volatile solids were recirculating and concentrating in the treatment plant, resulting in an increase of MLSS and a decrease in F/M ratio at the activated sludge system. Special attention is required for long term operations since the increase of non-volatile solids in the plant would deteriorates the treatment efficiency. The sewage sludge of the Chunan sewage treatment plant showed 79.5% of water content, 11.6% of organic content, and C/N ratio of 6.1, and contained As 1.8 mg/kg, Cd 27 mg/kg, Hg <0.1 mg/kg, Pb 54 mg/kg, T-Cr 370 mg/kg, and Cu 1,100mg/kg of heavy metals. In order to be used as raw material for optimum composting, the sewage sludge requires bulking agents for moistrure/porosity control and a carbon source for adjusting C/N ratio. However, the sewage sludge is not adequate as a soil conditioner after composing due to a high content of heavy metals. If the sewage sludge has to he used as a soil conditioner after composting, it as required to identify and remove tire industrial wastewater portions in tire influent of the plant since heavy metals in the influent were mostly concentrated in dewatered sludge.

• Journal of Engineering Education Research
• /
• v.4 no.1
• /
• pp.57-78
• /
• 2001

Due to developments in information technology and ensuing changes in the concept of time and space, the significance of national boundaries has been weakened, bringing to attention the heightened competition among nations. In order to respond to these transformations, the Korean government is increasing its efforts to raise the authenticity of the National Technology Qualification System(NTQS) by closely linking NTQS testing method and procedure to practical knowledge and skills in the industry field. This initiative is based on the recognition that the human resources development is a crucial factor in determining a nation's competitiveness. This study aimed, first of all, to diagnose the problems directly and indirectly affecting the testing method in the current NTQS. And then, differentiated solutions according to grade and improvements in the testing infrastructure were suggested. The ultimate purpose was to provide a blueprint for enhancing national competitiveness through increased authenticity and efficiency of the NTQS. Research methods applied during this study include: the collection and review of qualification-related literature; a series of conferences with leading experts; interviews with vocational educators and researchers from qualification-related institutes; a survey of national qualification holders from a variety of professions and industries; and participatory observation at qualification exam centers. This research suggested policy recommendations as follows; First, measures to improve for testing method of professional engineer Second, measures to improve for testing method of Master craftsman Third, measures to improve for testing method of Engineer, Industrial Engineer, Craftsman Fourth, plans for the establishment of operation system for a computerized testing Fifth, institutional perspective on establishing qualification infrastructure Sixth, operational perspective on establishing qualification infrastructure

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.100-105
• /
• 2016

The use of 3D scanners has increased gradually according to increasing 3D printer applications. The precision inspection of car parts or electronic components is an important issue not only in the field of mass production, but also in small-scale production. Recently, 3D scanner equipment efficiency and recognition technology has been improved continuously. On the other hand, the spraying time to prepare 3D scanning is time-consuming and has environmental problems. Therefore, an automatic spray system has been in demand by the manufacturing industry. Automatic spray equipment was newly developed for the preparation of a 3D scanner. In this research, the automatic spray system guarantees uniform spray operation. To determine the optimal spray parameters, various spraying methods, solutions and conditions were tested and compared with the experiments. The preparation time for 3D scanning was reduced to 1/10 compared to the manual spraying time, and indicates the optimal spraying conditions through a comparison of various spray coating conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.5
• /
• pp.1573-1579
• /
• 2010

In this paper, we studied efficient design of wireless transmission system for unified data transmission in a subway and railway. It is increased that need of broadband multimedia service to make useful environment for users and to support the operation of railway system. High bandwidth is better if we need more services. But, high bandwidth requires more cost at tunnel of subway. And more bandwidth makes received antenna sensitivity bad. So it needs more wireless stations. We deduced best bandwidth for subway wireless transmission system using the cost of installation and efficiency of system. Consequently, we proposed efficient service model for broadband wireless system at a subway. Subway broadband wireless transmission system is testing and extended to province subway. The cost of subway broadband wireless transmission system is saved, because the system can be efficiently designed using proposed service model. Therefore, the effectiveness of it will be expected to be very big.

• Journal of Energy Engineering
• /
• v.26 no.4
• /
• pp.29-34
• /
• 2017

Factors of Zero-Energy Building are divided into active and passive factor. Passive factor means insulation, heat bridge of building like insulation, windows and doors, awning, outside etc. and active factor means energy output and efficiency coefficient. Energy output of active factor is achieved by new generating energy. This study anticipated how many effects will be produced when not new generating energy but Vehicle to Building; V2B, bi-directional charging and discharging technology, is applied to Zero-Energy Building. In new generating energy, power generation will be anticipated by geography and climate, but in V2B, several input variable like user's discharging intention and number of usable charger etc. should be considered. We can check how much V2B contribute to the Zero-Energy Building by anticipated results, and that results should be anticipated by using probabilitic method because there is few statistical data. This study anticipate change of charging and discharging pattern, based by Demand Response slot, by using monte carlo method among the probabilitic methods.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.39 no.4
• /
• pp.326-336
• /
• 2003

In order to modify the construction of gizzard shad coastal purse seine net with possible to the laborsaving of fishing operation in the coastal small fishing vessels, the model experiments were carried out on the model nets for several conventional nets using in the field and the experimental nets was manufactured as 1/100 and 1/60 of the full scale net. The results obtained are summarized as follows；1. In the case of the conventional net and reduction rate 75% in conventional net with purse line the fishing efficiency decreased, the lead line was upward for the surface and the pursing depth of pursing line was very shallow to 2∼3m. 2. In the case of the net having maximum depth in center part designed in this study, the length of float and lead line was 60% of conventional net, the depth of net was fixed 20m to selvage line of the both of the end and extend gradually with 50m, 40m, 30m to the center. Among the these net, depth of pursing line was 20∼23m for 50m and 7∼15m for 40m, 30m the depth of net. These results were suitable for interception of fish school in fishing ground, but several problems will be caused by the depth and current of fishing ground.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.47 no.2
• /
• pp.79-87
• /
• 2011

A fishing lamp is fishing gear to gather fish in the night. But the cost of oil which is used to a light fishing lamp, goes significantly up to almost one hundred million won for 50 tonnage vessels and forty million won in case of vessels less than 10 tonnages. This cost has almost taken 30.40% of total fishing costs. As oil price increases, the business condition of the fishery gets worse and worse. Therefore, it is very urgent to develop an economical fishing lamp, to solve the problem of fishery's business difficulty. This research aims at developing a fishing lamp for squid jigging fishery and hairtail angling fishery using the LED, which has excellent efficiency and durability. One fishing lamp has about 160Watt capacity and five fishing lamps are installed one aluminium panel in which sea water flows to emit generated heat from LED to outside. Developed fishing lamp lights to an effective direction of jigging and angling operation. This fishing lamp can be controlled to light the direction of fish shoal because the aluminium panel can be controlled to up and down direction. The wave length of fishing lamp has white and blue color. White color light is to gather fish shoal of horizontal direction and blue color light is to gather fish shoal of vertical direction. After development of this fishing lamp, 60.110 units are established on the boat, and operated fishing. Consequently, in the case of squid jigging, spent energy was reduced to 39%, in the case of hairtail angling, 68% of spent energy was reduced. And the catch was more than another boat.

• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.575-580
• /
• 2020

In this study, we simulated an amine regeneration process with heat-stable salts removal unit. We derived the optimal operating conditions considering the flow rate of waste, the removal rate of heat-stable salts, and the loss rate of MDEA (methyl diethanolamine). In the amine regeneration process that absorbs and removes acid gas, heat-stable salt impairs the absorption efficiency of process equipment and amine solution. An ion exchange resin method is to remove heat-stable salts through neutralization by using a strong base solution such as NaOH. The acid gas removal process was established using the Radfrac model, and the equilibrium constant of the reaction was calculated using Gibbs free energy. The removed amine solution is separated and flows to the heat-stable salts remover which is modeled by using the Rstoic model with neutralization reaction. Actual operation data and simulation results were compared and verified, and also a case study was conducted by adjusting the inflow mass of removal unit followed by suggesting optimal conditions.

• Korean Journal of Food Science and Technology
• /
• v.7 no.1
• /
• pp.30-36
• /
• 1975

The extraction efficiency of orange-yellow pigment from the Gardenia was greatly depended upon the extraction time, extraction temperature, volume of solvent used and fat contents of the Gardenia. From the experimental results, the amounts of extracted pigment (P) was proportional to the $log\;t^{\;1{\cdot}15}$ of extraction time$(t;\;0{\sim}60\;min.)$, the $log\;T^{3{\cdot}73}$ of extraction temperature$(T;\;5{\sim}60^{\circ}C)$, the $log\;S^{3{\cdot}7}$ of volume of solvent$(S;\;5{\sim}50\;ml)$, and the -4X of fat contexts of sample $(X;\;0{\sim}0.\;15)$ at $18^{\circ}C$ for 10 minutes. Finally, the modified empirical equation was derived as follow; $P{\simeq}1.15\;log\;t+3.73\;log\;T+3.7\;log\;S-4X-6.4$ In addition to that, the most optimum conditions of pigment extraction were determined as 30 minutes of operation time, $40^{\circ}C$ of temperature. Deffated Gardenia was more productive than natural Gardenia in the pigment extraction.