• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.24-27
• /
• 2008

For high voltage DC-DC converters, the parallel operation of several high voltage source modules is necessary to reduce the material cost. In the conventional parallel operation with HDC module control unit, it is difficult to repair the HDC system for the failure of control unit. To overcome these problems, new parallel operating algorithm for high voltage DC-DC converter is presented. The proposed algorithm has no main control unit and each module can be selected as the master according to the operating conditions. Therefore, one of modules can be replaced as the master immediately when the previous master module is failed. In addition, the extension of extra modules can be simple.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.1
• /
• pp.109-116
• /
• 1998

This paper is concerned with effective operating method of pneumatic on-off valves for improving position control accuracy, valve life-time and position settling time using modified pulse width modulation with dead-zone (MPWMD). The pneumatic system using on-off valves has advantage of simple construction and low cost compared with a system with servo-valves. The performance of the proposed control method is investigated experimentally for the position control of a pneumatic cylinder using on-off valves. Experimental results show that the proposed algorithm for valve operation can be used to obtain fast and accurate position control compared to the conventional PWMD algorithm. It is also shown that the use of the proposed MPWMD algorithm for the position control significantly reduces the number of valve switching and noise.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.3
• /
• pp.585-591
• /
• 2016

DOCR can be used to efficiently increase the reliability and to protect the bi-directional D/L(Distribution Lines). As more DG(Distributed Generation)s attempt to connect the bi-directional D/L, there is an increasing need for studies of how to use DOCR installed in the D/L. This paper investigates the operating principles of DOCR and presents the results an effect of sequence and fault impedance in L-L(Line to Line) fault. An advanced DOCR operating algorithm is proposed to reduce the mal-operation of conventional DOCR. The proposed algorithm is applied to the bi-directional power flow system and shows that it decreases the mal-operation of DOCR through the computer simulation.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.449-451
• /
• 2001

This study presents a study on modified algorithm to operating train simulation of AT feeding systems. In this study equivalent impedance is constructed by $Z_c,\;Z_r,\;Z_f,\;Z_{cr},\;Z_{rf},\;Z_{fc}$. The train current flows through the all auto-transformer corresponding to track impedance. To calculate train voltage from analyzing the railway systems, the algorithm is based on the K. C. L, K. V. L, superposition and circuit separation method. Multi-train's voltages are determined by calculating the catenary voltage at each train's position and adding up these train's voltage drop. Case studies use a field operational data, show that the proposed method is easily applied.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.4
• /
• pp.571-579
• /
• 1990

A dynamic relocation algorithm for non-deterministic process graph in distributed computer systems is proposed. A method is represented for determining the optimal policy for processing a process tree. A general database query request is modelled by a process tree which represent a set of subprocesses together with their precedence relationship. The process allocation model is based on operating cost which is a function fo selection of site for processing operation, data reduction function and file size. By using expected values of parameters for non-deterministic process tree, the process graph and optimal policy that yield minimum operating cost are determined. As process is relocated according to threshold value and new information of parameters after the execution of low level process for non-deterministic process graph, the assigned state that approximate to optiaml solution is obtained. The proposed algorihtm is heuristic By performing algorithm for sample problems, it is shown that the proposed algorithm is good in obtaining optimal solution.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.299-303
• /
• 2011

This paper proposes a novel sensorless maximum power point tracking (11PPT) algorithm for PV systems. The method is based on dividing the operating time into several intervals in which the PV terminals are short circuited in one interval and the calculated short-current of the PV is obtained and used to determine the optimum operating point where the maximum output power can be obtained. The proposed MPPT algorithm has been introduced into a current-controlled boost converter whose duty ratio is controlled to the maintain MPP condition. The same sequence is then repeated regularly capturing the PV maximum power. The main advantage of this method is eliminating the current sensor. Meanwhile, this MPPT algorithm reduces the power oscillations around the peak power point which occurs with perturbation and observation algorithms. In addition, the total cost will decrease by removing the current sensor from the PV side. Finally, simulation results confirm the accuracy of the proposed method.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2007.04a
• /
• pp.74-77
• /
• 2007

In this paper, we propose a system which can display panoramic-stereopic image for tele-operating excavator. the system was implemented by using center-viewpoint corresponding algorithm and image mosaic process. We could obtain remarkable result from the survey among the ex-pert of excavator. We also design a control station with RF transfer module, H.264 codec module and suggested algorithm. Especially, our system shows a superb performance on cubic effect and presence sense of a field of excavating work.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.20 no.43
• /
• pp.139-144
• /
• 1997

The objective of this study is to establish an actual optimization strategy for the traditional multi-stage distribution system which consists of factory warehouse, central distribution warehouse, and regional distribution warehouse under the basic assumption of distribution system. A minimization algorithm of total operating cost in a multi-stage distribution system was developed by expanding the previously existing algorithm through consideration of additional transportation environment. Alternative non-linear transportation costs for the same travel distance can be applied for the multi-stage distribution system by estimating the corresponding characteristic values through the collection of the actual data representing the change of transportation circumstances.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.325-327
• /
• 2007

This paper proposes a novel sensorless fault detection algorithm for a brushless DC(BLDC) motor drive system. This proposed method is configured without the additional sensor for fault detection and identification. The fault detection and identification are achieved by a simple algorithm using the operating characteristic of the BLDC motor. This proposed method can also be embedded into existing BLDC motor drive systems as a subroutine without excessive computational effort. The feasibility of a novel sensorless fault detection algorithm is validated in simulation.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.443-444
• /
• 2014

Using the ESS(Energy Storage System) as a UPS(Uninterruptible Power Supply) is being studied recently. When the system is operating at UPS mode in integrated ESS and UPS system, the grid supplying power is disconnected and power from PV generation and battery are supplying to load. Operating in UPS mode, when PV generation power is diminished by partial or total clouded situation, DC-link voltage fluctuates. The fluctuation of DC-link voltage influences the load and system as sensitive loads may malfunction. This paper suggests the DC-link ripple voltage compensation algorithm in bi-directional converter. The algorithm stabilize the DC-link and load voltage.