• 한국소음진동공학회논문집
• /
• 제20권5호
• /
• pp.502-509
• /
• 2010

A test facility which can simultaneously measure turbocharger operating condition variables and vibro-acoustic emission in the situations that are quite similar to real internal combustion engine operating conditions has been introduced. Using this facility, a new method sweeping from full open throttle to deep surge region along constant speed curves can be utilized instead of the stationary method that has been traditionally used to obtain turbocharger compressor maps. Data covering an extensive range of the compressor performance map have been collected and analyzed. An experimental study is performed to define a noise diagram that correlates vibro-acoustic measurements to aerothermodynamic operating conditions. An instrumentation set in the facility allows the automatic definition of the operating point on the turbine and compressor map of the turbocharger. Also, radiated sound pressure and casing vibration data corresponding to the point are obtained by a microphone in the vicinity of the compressor casing and an accelerometer on the casing. The major source(s) of noise at specific operating point on the map can be easily identified with these maps. Also, acoustic characteristics of a given turbocharger at the vicinity of the surge as well as in the surge are also defined. Finally, the possibility to define mild surge region of a turbocharger using vibro-acoustic measurements is studied.

• 대한수학회지
• /
• 제42권6호
• /
• pp.1251-1264
• /
• 2005

Let D be an acyclic digraph. The competition graph of D has the same set of vertices as D and an edge between vertices u and v if and only if there is a vertex x in D such that (u, x) and (v, x) are arcs of D. The competition number of a graph G, denoted by k(G), is the smallest number k such that G together with k isolated vertices is the competition graph of an acyclic digraph. It is known to be difficult to compute the competition number of a graph in general. Even characterizing the graphs with competition number one looks hard. In this paper, we continue the work done by Cho and Kim[3] to characterize the graphs with one hole and competition number one. We give a sufficient condition for a graph with one hole to have competition number one. This generates a huge class of graphs with one hole and competition number one. Then we completely characterize the graphs with one hole and competition number one that do not have a vertex adjacent to all the vertices of the hole. Also we show that deleting pendant vertices from a connected graph does not change the competition number of the original graph as long as the resulting graph is not trivial, and this allows us to construct infinitely many graph having the same competition number. Finally we pose an interesting open problem.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.11-19
• /
• 2004

When pile foundation constructed by driving method, it is desirable to perform monitoring and estimation of pile drivability and bearing capacity using some suitable tools. Dynamic Pile Monitoring yields information regarding the hammer, driving system, and pile and soil behaviour that can be used to confirm the assumptions of wave equation analysis. Dynamic Pile Monitoring is performed with the Pile Driving Analyser. The Pile Driving Analyser (PDA) uses wave propagation theory to compute numerous variables that fully describe the condition of the hammer-pile-soil system in real time, following each hammer impact. This approach allows immediate field verification of hammer performance, driving efficiency, and an estimate of pile capacity. The PDA has been used widely as a most effective control method of pile installations. A set of PDA test was performed at the site of Donghea-1 Gas Platform Jacket which is located east of Ulsan. The drilling core sediments of location of jacket subsoil are composed of mud and sand, silt. In this case study, the results of PDA test which was applied to measurement and estimation of large diameter open ended steel pipe pile driven by underwater hydraulic hammer, MHU-800S, at the marine sediments were summarized.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.556-560
• /
• 2011

The seawater lift pump system is responsible for maintaining the open canal level to provide the suction flow of circulating water pump at the set point. The objective of this paper is to design a 2-stage mixed flow pump(for seawater lifting) by inverse design and to evaluate the overall performance and the local flow fields of the pump by using a commercial CFD code. Rotating speed of the impeller is 1,750 rpm with the flow rate of 2,700 $m^3/h$. Finite volume method with structured mesh and Realizable ${\kappa}-{\varepsilon}$ turbulent model is used to guaranty more accurate prediction of turbulent flow in the pump impeller. The numerical results such as static head brake horse power and efficiency of the mixed flow pump are compared with the reference data. Also, the periodic condition calculation method for the mixed flow pump was carried out in order to investigate the pump performance characteristics with the modification of impeller geometry.

• Ocean Systems Engineering
• /
• 제1권1호
• /
• pp.17-28
• /
• 2011

The purpose of this paper is to demonstrate the efficacy of modeling a surface effect ship's air-cushion flexible seal utilizing a two-dimensional beam under steady state conditions. This effort is the initial phase of developing a more complex three-dimensional model of the air-seal-water fluid-structure interaction. The beam model incorporates the seal flexural rigidity and mass with large deformations while assuming linear elastic material response. The hydrodynamic pressure is derived utilizing the OpenFOAM computational fluid dynamic (CFD) solver for a given set of steady-state flow condition. The pressure distribution derived by the CFD solver is compared with the pressure required to deform the seal beam model. The air pressure, flow conditions and seal geometry are obtained from experimental analysis. The experimental data was derived from large-scale experimental tests utilizing a test apparatus of a canonical surface effect ship's flexible seal in a towing tank over a variety of test conditions.

• 설비공학논문집
• /
• 제25권2호
• /
• pp.79-84
• /
• 2013

In this study, a cold aisle containment system was proposed among various strategies to reduce the energy waste by recirculation air from the hot aisle. To verify the effectiveness of the cold aisle containment system, a test bed which is similar to an actually existing server room was set up in the Internet Data Center(IDC) building. Comparative experiments, conventional open type cooling system and cold aisle containment system were carried out under actual conditions. The result revealed that the range of inlet temperature of the server system was $20{\sim}25^{\circ}C$ in an existing cooling system and the range of inlet temperature dropped below $20^{\circ}C$ by the cold aisle containment system. After all, cold aisle containment system was proved to be the solution for energy saving cooling system.

• 대한수학회논문집
• /
• 제26권1호
• /
• pp.135-149
• /
• 2011

Using (r, s)-preopen sets [14] and pre-${\omega}_t$-closures [6], a new kind of covering property $P^t_{({\omega}_r,s)}$-closedness is introduced in a bitopological space and several characterizations via filter bases, nets and grills [30] along with various properties of such concept are investigated. Two new types of cluster sets, namely pre-(${\omega}_r$, s)t-${\theta}_f$-cluster sets and (r, s)t-${\theta}_f$-precluster sets of functions and multifunctions between two bitopological spaces are introduced. Several properties of pre-(${\omega}_r$, s)t-${\theta}_f$-cluster sets are investigated and using the degeneracy of such cluster sets, some new characterizations of some separation axioms in topological spaces or in bitopological spaces are obtained. A sufficient condition for $P^t_{({\omega}_r,s)}$-closedness has also been established in terms of pre-(${\omega}_r$, s)t-${\theta}_f$-cluster sets.

• 화약ㆍ발파
• /
• 제22권3호
• /
• pp.1-12
• /
• 2004

암석 파쇄도는 노천의 벤치발파에서 생산성을 좌우하는 요소이다. 벤치발파에서 암석 파쇄도는 여러 가지 조건의 영향을 받게 되는데, 특히 암반의 불연속면 조건과 자연상태 암반 블록의 크기는 큰 영향을 미치는 것으로 알려져 있다. 이 연구에서는 석회석을 생산하는 3개 노천광산에서 발파조건 뿐 아니라 암반의 불연속면 조건과 자연상태 암반 블록크기를 면밀히 조사하여 이들 조건이 암석 파쇄도에 미치는 영향을 검토하였다. 분석 결과 암반의 불연속면 조건과 발파조건은 복합적인 상호작용에 의해 영향을 미치는 것으로 밝혀졌으며, 특히 자연상태 암반 블록의 크기는 암석 파쇄도에 가장 큰 영향을 미치는 것으로 나타났다. 암석 파쇄도는 암반의 불연속면 조건 중 주절리군의 방향에 의해서도 영향을 받는 것으로 확인되었는데, 주절리군의 방향이 벤치 앞쪽 자유면과 $30^{\circ}$의 경사를 이룰 때 파쇄물의 평균크기가 가장 작게 되는 것으로 나타났다. 이런 현상은 발파로 만들어진 탄성파의 전파경로 차이에 기인하는 것으로 판단된다.

• 한국의류산업학회지
• /
• 제22권3호
• /
• pp.335-348
• /
• 2020

This study examines the cultural differences in Korea and the United Kingdom, and how they affect consumer complaint behavior(CCB). Technological advances allow consumers to easily access information anywhere in the world using the internet thus they demand even higher expectations from the sellers. Consumers from different cultural backgrounds, especially the millennial generation, have different ways of expressing a dissatisfying shopping experience. For this comparative study, in-depth interviews were conducted based on the methodology set by grounded theory. The results of the axial coding produced by recombining the data from open coding were visualized as a paradigm model. The main phenomenon of attitude towards complaining was formed following the causal conditions of dissatisfaction that occurred after purchasing fashion products online. The contextual condition, which is the cultural factors, affects the formation of the attitude towards complaining; and the intervening conditions, which are personal value and amplifications of dissatisfaction, had a moderating effect between the causal condition and the main phenomenon. Complaining costs, the likelihood of successful complaint, attribution, and the importance of the product were the determinants of the complaining behavior after the attitude towards complaining was formed. As a result, there were three classifications of consumer complaining behavior: no action, private action, and public action. This research will serve as a guide for online companies that wish to enter the UK fashion industry with a competitive edge.

• 대한조선학회논문집
• /
• 제50권5호
• /
• pp.282-290
• /
• 2013

The effects of the combination of blade number for forward and after propeller on the propeller shaft forces of a contra-rotating propeller (CRP) system are presented in the paper. The research is performed through the numerical simulations based on the Reynolds-Averaged Navier-Stokes equations (RANS). The simulation results of the present method in open water condition are validated comparing with the experimental data as well as the other numerical simulation results based on the potential method for 4-0-4 CRP (3686+3687A) and 4-0-5 CRP (3686+3849) of DTNSRDC. Two sets of CRP are designed and simulated to study the effect of the combination of blade number in behind-hull condition. One set consists of 3-blade and 4-blade, while the other is 4-blade and 4-blade. A full hull body submerged under the free surface is modeled in the computational domain to simulate directly the wake field of the ship at the propeller plane. From the simulation results, the fluctuations of axial force and moment are dominant in the case of same blade numbers for forward and after propellers, whereas the fluctuations of horizontal and vertical forces and moments are very large in the case of different blade numbers.